REPEATIT Trinity-323 Kurzanleitung

Trinity-300

Series

Installation and

Operational Guide

Repeatit AB

Tel: +46 8 570 106 66

Hamngatan 33 Fax: +46 8 570 106 67

172 66 Sundbyberg

E-mail: info@repeatit.se

Sweden

www.repeatit.se

Quickstart

Before proceeding with the installation, verify that the

equipment

works on the ground. Power up both units and put

them between

your computer and network access, you should

have full communication within a few minutes of powering up

the units. (If the

units have no internal antenna make sure you

place the antenna

connectors directly opposite each other.)

Both the units are pre-configured in Master mode with the same

IP address, user name and password:

IPaddress

Username

Password

10.0.0.1

admin

public

Client mode so they connect to each other.

Installing the link

•

Mount the first unit and point it towards the site of the

second

unit. Power it up and make sure the Power LED is lit

and the

status LED blinks slowly.

•

Mount the second unit. Power it up and adjust it for best signal

using the status LED see section 1.9 for details .

electricity/safety competence and who is familiar with

•

Adjust the first unit for best signal using the Status LED.

Trinity-300 Series

•

Make sure all cables are secured and connect the link to the

network.

•

Configure the distance parameters at the master unit to

reflect the correct distance between the units.

Note Make sure that the polarization on both units is the

same. Unaligned polarization will significantly reduce

the

signal strength. For more information about antenna

polarization and how to successfully tune the links for good

performance, refer to Repeatits’Deployment Guideline

document.

Contents

Installation Guide 4

1.1

Who should use this guide ...................................................... 4

1.2

Package contents......................................................................

1.3

Additional toolsrequired .......................................................5

1.4

Unit description ....................................................................... 5

1.5

Installation................................................................................ 5

1.6

Mounting a Trinity-300 unit....................................................6

Mounting instruction for Trinity-323 and Trinity-316 . . 7

Mounting instruction for Trinity-300 7

1.7

Ethernet cabling ...................................................................... 8

1.8

Installing the powersupply ...................................................8

1.9

Finalizing the installation.......................................................9

Configuration................................................................................

Alignment......................................................................................

Securing theinstallation..................................................... 10

Configuration

2.1

Trinity-300 series Configurationconcepts ........................ 11

Configuration areas ................................................................

2.2

Configuring using the Trinity-300 series web interface 12

Modifying the configuration ............................................... 12

Applying a new configuration ............................................ 12

Saving settings to flash memory....................................... 13

Rolling back settings ........................................................... 14

2.3

Configuration parameters....................................................15

Radio settings ..........................................................................

CAC Policy ....................................................................................

Network settings ...................................................................19

System settings.....................................................................20

Unit Operation 21

3.1

Unit status ............................................................................ 21

Default view ......................................................................... 21

Trinity-300 Series CONTENTS

Extended information......................................................... 21

Status information .............................................................. 22

3.2

Link Diagnostic Tools.......................................................................23

Spectrum analyzer ............................................................. 23

Speed test............................................................................ 24

3.3

Firmware upgrading ........................................................... 25

3.4

Restore to defaults ............................................................. 25

Support 26

Technical Specifications 27

Usage restrictions and legal information 28

CONTENTS

Installation Guide

1.1

Who should use this guide

Installing fixed outdoor radio links requires technical expertise and

should only be carried out by a trained technician. You should only

attempt to install and configure the Trinity link

if you have

•

Experience in mounting outdoor radio equipment and

aligning antennas.

•

Understanding, or common knowledge, about network

equipment.

•

Made sure that the installation site is suitable and complies

with local radio, electrical and safetyregulations.

1.2

Additional tools required

Depending on the conditions at the installation site other tools

might be needed, including, but not limited to

•

Cat5E Ethernet cable

•

RJ-45 crimp tool and RJ-45 connectors if not using a pre-assembled

Ethernet cable

•

An adjustable wrench

•

Drill for wall mounting

•

Ground cables

•

Cable ties to secure cabling

1.3

Unit description

There are three LEDs on the units: power, status and Ethernet

link/activity.

LED

Colour

Status

Description

Power (P)

Status (S)

Green

Flashing

Blinking

Power on

Signal strength pattern

Firmware

upgrade

rogress

Ethernet(E)

Green

On/blinking

Reflects Ethernet traffic

and link status

Off

No Ethernetlink

1.4

Installation

Installing a Trinity-300 system consists of the steps outlined

below. Each step is explained more thoroughly in the following

sections. The Trinity-300 system consists of two Trinity-300

units, one master unit and one client unit, the installation

steps

needs to be carried out for both units.

Before taking the units to the site, configure one of them to

be the Master and the other one to be the Client. Normally

this is done in an office environment. Note that link

throughput can be degraded by multipath effects and other

RF related phenomenon in an office. Therefore, just make

sure that the links connect to each other and have proper IP

settings before taking them to the site.

Mount the Trinity-300 unit and antenna (if applicable)at

site

Install the PoE at an indoor location where power and network

equipment is available.

Run Ethernet cable from the PoE to the mounted Trinity-300

unit.

Repeat the above steps for the unit at site B.

Align antennas for best signal reception. For longer distances,

this normally requires re-alignment of antennas on both sides

of the link.

For optimal link throughput the following parameters must be

updated in the web interface

•

Distance - should accurately reflect the distance in

kilometers between the units.

Andere Handbücher für Trinity-323

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere REPEATIT Drahtloser Zugangspunkt Handbücher

REPEATIT

REPEATIT Trinity-123 Lite Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung