RETRO EMRX Bedienungsanleitung
AQUA/LAMP®POOL LIGHTS
Replaces existing:
2
3
4
5
6
7
10
11
13
CONTENTS
PRODUCT SUPPORT & INFORMATION
CANADA INTERNATIONAL
Select Pool Products Spa Electrics PTY LTD
www.spaelectrics.com
www.selectpoolproducts.ca
Tel: 1-855-881-0889
Email: info@selectpoolproducts.ca
1
READ THIS FIRST / PRODUCT WARNINGS
TOOLS REQUIRED / WINTERIZATION
INCLUDED PARTS
BEFORE YOU START
EXISTING LIGHT REMOVAL / CABLE PREPERATION
CABLE JOINER INSTALLATION
LIGHT INSTALLATION
LIGHT REMOVAL / WINTERIZATION
ELECTRICAL GROUNDING / FCC COMPLIANCE
Congratulations on your purchase of a Spa Electrics ATOM Retro Series pool light,
for safe and proper installation, please read the installation manual carefully
prior to product installation.
For safe & proper installation, use only parts (screws, plugs, sealant etc) provided.
The ATOM Retro Series EM Light must be water cooled at all times. DO NOT switch
the light on until installation is complete and the light is fully submerged in water.
Ensure sufficient cable is coiled behind the light to allow for servicing
Ensure only circular cable not exceeding 14mm diameter is connected to the
supplied cable joiner. The use of Figure 8 or non circular cable will prevent correct
sealing & will void the product warranty.
The ATOM Retro Series EM Light does not contain any user serviceable parts,
opening the light head will void the product warranty.
Pool chemicals & pH levels: Due to the corrosive nature of unbalanced pool
chemicals, Spa Electrics strongly recommends that your pool water is balanced
prior to installing your pool Lights or any plastic or stainless steel components,
and tested weekly to maintain these levels. pH levels should be maintained between
7.2- 7.6 at all times to ensure the longevity of these components.
Failure to do so can result in chemical damage to the light housing and
pool fittings, including stainless steel components.
Please note: Lights or components found to have excessive chemical
damage will not be covered under our manufacturer’s warranty policy
READ THIS FIRST
WARNING
The ATOM light must only be used with a UL listed 12V AC power supply or a power source
intended for swimming pool use (not included).
Minimum power source wattage requirement - 15 Watts per light.
ELECTRICAL SUPPLY NOTICE
2
TOOLS REQUIRED
Side cutters / Pliers
Small flat-blade screwdriver (supplied)
24mm / 29mm wrench (supplied)
• The use of power tools during installation is not recommended as these
devices can cause faults and damage to light components.
• All installation steps should be carried out with manual tools only.
• The enclosed images are for illustrative purposes only. Appearances of parts
and assemblies may vary from the enclosed illustrations.
• Please contact your reseller if you have any questions regarding the correct
installation of this product.
IMPORTANT NOTES
WINTERIZATION
• Lights must be removed from pool wall and cable disconnected via plug &
stored in a dry and safe place. Cable joiner should remain connected.
• Red Terminal Cover must be fitted to Plug Top during the winter.
• Consult your local pool professional for complete pool winterization process.
3
1 X RETRO LIGHT
PLUG CONNECTION
UNDERWATER
CABLE JOINER
INCLUDED PARTS
ADAPTOR PLATE
(To suit existing AQUA/LAMP® )
SCREW DRIVER WRENCH
18” OF 18AWG CABLE
24
29
PREASSEMBLED
TERMINAL
COVER FOR
WINTERIZATION
4
ON
OFF
BEFORE YOU START
1ISOLATE POOL LIGHTS
2CHECK TRANSFORMER
EXISTING TRANSFORMER
MUST BE:
EXISTING TRANSFORMER
MUST NOT BE:
MIN. 15 WATT (PER LIGHT)
IN GOOD WORKING ORDER
DC OR ‘LED DRIVER’
ELECTRONIC OR SWITCH MODE
WEATHER DAMAGED OR IN
OTHERWISE POOR CONDITION
12V AC POWER
SUPPLY/POWER SOURCE
INTENDED FOR SWIMMING POOL USE
ENSURE SYSTEM IS SAFELY
ISOLATED DURING THE
INSTALLATION PROCESS.
IF IN DOUBT; CONTACT YOUR
ELECTRICAL CONTRACTOR FOR
ASSISTANCE.
5
REMOVAL OF EXISTING LIGHT
REMOVE EXISTING POOL
LIGHT FROM POOL WALL BY
ROTATING CENTRE LIGHT FITTING
COUNTER-CLOCKWISE.
DISCONNECT CABLE TO
EXISTING POOL LIGHT,
ENSURING ENOUGH CABLE
LENGTH REMAINS IN THE
NICHE ABOVE THE
NOMINAL WATER LEVEL TO
ENSURE SERVICE ACCESS.
1.
1.
2.
STRIP CABLE OUTER AND
INNER SHEATHS TO THE
BELOW LENGTH.
1REMOVE EXISTING LIGHT
2PREPARING EXISTING CABLE
10mm
EXISTING CABLE
10mm
NICHE LIGHT
1
2
6
LOOSEN OUTER CABLE
GLAND NUTS.
LOOSEN AND REMOVE
BOTH THREADED HEX
NUTS USING 29mm
WRENCH.
PLACE CABLE GLAND NUT
AND THREADED HEX NUT
OVER RETRO LIGHT CABLE.
INSTALLING CABLE JOINER
1OPEN CABLE JOINER
2CONNECT RETRO LIGHT CABLE
1
1
2
2
24mm
RETRO
LIGHT
EXISTING
CABLE
29mm
IMPORTANT
CONNECT WIRES TO
TERMINAL BLOCK USING
FLAT BLADE SCREW
DRIVER.
7
INSTALLING CABLE JOINER
SLIDE THREADED HEX NUT
OVER TERMINAL BLOCK.
ENSURING CABLE SHEATH
EXTENDS INSIDE THE
ASSEMBLY.
3
TIGHTEN CABLE GLAND NUT
USING 24mm WRENCH.
4
ATTACH MAIN BODY AND
TIGHTEN USING 29mm
WRENCH.
5
8
INSTALLING CABLE JOINER
3CONNECTING TO EXISTING CABLE
SLIDE THREADED HEX NUT OVER
TERMINAL BLOCK AND TIGHTEN ONTO
MAIN BODY USING 29mm WRENCH.
PLACE CABLE GLAND NUT AND THREADED
HEX NUT OVER EXISTING LIGHT CABLE.
1
1
2
3
TIGHTEN CABLE GLAND NUT
USING 29mm WRENCH.
4
2CONNECT WIRES TO TERMINAL BLOCK
USING FLAT BLADE SCREW DRIVER.
9
Inhaltsverzeichnis
Andere RETRO Unterwasserbeleuchtung Handbücher
Beliebte Unterwasserbeleuchtung Handbücher anderer Marken
Keldan
Keldan VIDEO 18X 25000lm CRI82 Bedienungsanleitung
Oase
Oase ProfiLux Garden LED RGB Bedienungsanleitung
Oceanled
Oceanled DISCOVER D3 Bedienungsanleitung
NORBIT
NORBIT AQUA FCL600 Bedienungsanleitung
Keldan
Keldan VIDEO 8XR Ambient 18000lm Bedienungsanleitung
Ikelite
Ikelite PCm - LED Light Bedienungsanleitung
