RGK LP-62 Bedienungsanleitung
Laser level
LP-62
LP-64
LP-62G
LP-64G
3
Contents
Level components 5
Device specications 6
Purpose of the device 7
Installing batteries 7
Work process 8
Level accuracy check 9
4
Warning
The RGK laser level uses a laser light source. Do not direct
the laser beam into your eyes, as this may result in injury. Ob-
serve the rules of care and operation, do not disassemble, re-
pair, or modify the device - this may lead to the device failure.
Attention:
Batteries can leak and damage the instrument, or even ex-
plode and cause a re. To reduce this risk, read the informa-
tion on the batteries and observe the following guidelines:
• note the polarity;
• replace all batteries at once with new ones;
• do not allow short circuits in the battery compartment;
• do not recharge non-rechargeable batteries;
• do not use old and new batteries together;
• do not use different type batteries together;
• do not leave batteries inside the device if it is not used for
a long time;
• do not give batteries to children and animals;
• do not dispose of batteries in re;
• Do not dispose of batteries with household waste, recycle
them according to local regulations.
5
Level components
6
Device specications
RGK
LP-62
RGK
LP-62G
RGK
LP-64
RGK
LP-64G
Laser line colour red green red green
Number of vertical lines 2 2 4 4
Accuracy ±1mm/5m
Auto leveling range ±4°
Working distance (radius) 20 m 30 m 20 m 30 m
Wavelength 635 nm 532 nm 635 nm 532 nm
Leveling system pendulum
Laser class 2М
Power supply AA batteries * 3
Working temperature range from -10° to + 45° С
Moisture protection IP54
Dimensions Ø150х190 mm
Weight 1,1 kg
7
Purpose of the device
The RGK LP laser level is a modern tool for marking work.
It is designed to build horizontal and vertical lines to check
horizontal and vertical surfaces, as well as to transfer heights
and apply markings.
The device automatically aligns to the horizon, can draw in-
clined lines and projects bright marker points on the cross-
hairs and on vertical planes to improve the visibility of the
beam.
The device is equipped with a closer for ne adjustment of
the position of vertical lines and a laser plummet.
The device is successfully used in the following works:
• alignment of walls, ceilings, oors;
• pouring oors, foundations, leveling sites;
• tiling and facing works;
• installation of suspended ceilings;
• installation work;
• interior work.
Installing batteries
• open the battery compartment cover;
• insert 3 AA batteries/accumulator, observing the polarity;
• replace the cover until it clicks into place.
8
RGK instruments are factory calibrated, underwent pre-sale
preparation, and tested for accuracy. However, we recom-
mend that you carry out periodic verication.
If the device has been dropped, stored unused for a long
time, transported over long distances, or subjected to shock,
we recommend that you carry out verication in the manner
described below. If the accuracy is unsatisfactory, do not try
to calibrate the device yourself, but contact the service center.
Work process
Place the device straight and use the set screws to center
the level.
Press the power button of the device, a horizontal line will
appear, and the device will automatically compensate.
The H key controls the enabling/disabling of the horizontal
line. The V key is responsible for turning on/off the vertical
line, pressing it again turns on the second (for LP-62), third
and fourth (for LP-64) vertical lines. The laser plummet turns
on when the V button is pressed. To work with inclined planes
with the device turned off, press the OUT button, and turn the
toggle switch.
9
Level accuracy check
Horizontal line accuracy check
Find a room with a distance of 5 meters between the walls.
Place the device on a tripod in the middle between the walls.
Turn on the horizontal beam and point it at the wall and mark
point a1 on wall A.
Turn the device 180 ° and mark point b1 on wall B. Move
the tripod with the device so that it is at a distance of 60 cm
from wall A, re-mark points a2 and b2. Measure the distance
between a1 and a2 and between b1 and b2. If the difference
(a2-a1) - (b2-b1)> 1.5 mm, contact the service center.
10
Vertical line accuracy check
Set up the device on a tripod a few meters away from the
wall.
Mark point A on the wall at a height of 3 m from the oor. Us-
ing a plumb line from point A on the oor, mark point B.
Turn on the instrument and align the vertical laser line with
point B. At a height of 3 m from the oor, mark point C on the
laser line.
Measure the distance e from point A to point C. If e> 1 mm,
contact the service center.
Dieses Handbuch passt für folgende Modelle
3
Inhaltsverzeichnis
Andere RGK Laser-Nivelliergerät Handbücher
Beliebte Laser-Nivelliergerät Handbücher anderer Marken
Nedo
Nedo ET-5 Bedienungsanleitung
geo-FENNEL
geo-FENNEL Maxi-Liner FL 65 HP Bedienungsanleitung
LaserLiner
LaserLiner X2-Laser Bedienungsanleitung
Spectra
Spectra LL300N Bedienungsanleitung
geo-FENNEL
geo-FENNEL Selection PRO FLG 40-PowerCross GREEN SP Bedienungsanleitung
Nedo
Nedo Crossliner 4 Bedienungsanleitung
