Ricoh PRO C7200 Installationsanleitung

2Throughput

CIP Training

Pro C7200 series

Startup and Shutdown.

Front and left view

DWP004

1. Main power switch

To operate the machine, the main power switch must be on. If it is off, open the main power switch's cover and

turn the switch on.

2. Front left cover

Open to remove paper jams or turn on/off the AC power switch.

CIP Training Pro C7200 series

Throughput

3. Control panel

See “Control Panel” module for detailed information. .

4. Front upper right cover

Open to change toner cartridges.

5. Front right cover

Open to remove paper jams.

6. Paper trays (Trays 1–2)

Load paper here. Tray 1 is a tandem tray where paper on the left side automatically moves to the right when

paper there has run out.

An indicator on the front left side of the tray lights while paper is feeding.

7. Front lower left cover

Open to replace the waste toner bottle.

8. AC power switch

Press to completely turn off the power of the machine. The AC power switch must be kept on in normal use.

The switch is inside the front left cover.

Turning On/Off the Power

•

The main power switch is on the top left of the machine. When this switch is turned on, the main power

turns on and the main power indicator on the right side of the control panel lights up. When this switch is

turned off, the main power turns off and the main power indicator on the right side of the control panel

goes out. When this is done, machine power is off.

Conﬁrm how much power the options draw, and then plug them into an outlet that is nearby but

separate from the outlet that the main machine is plugged into.

Turning On the Main Power

• This machine automatically enters Fusing Unit Off mode, Low Power mode, or Sleep mode if you

do not use it for a while.

1. Make sure the power cord is ﬁrmly plugged into the wall outlet.

2. Open the main power switch cover, and then push the main power switch.

The main power indicator goes on.

DER101

Do not push the main power switch repeatedly.

When you push the main power switch, wait at least 10 seconds after it is conﬁrmed that the main

power indicator has lit up or gone out.

If the main power indicator does not light up or go out in 5 minutes after you push the main power

switch, contact your service representative.

CIP Training Pro C7200 series

Throughput

Turning Off the Main Power

• After you switch the main power on, a screen may appear to indicate that the machine is

initializing. Do not switch the power off during this process. Initialization takes about 18 minutes.

However, the time for initialization may differ depending on which options are installed on the

machine.

• If the machine does not turn on even if you press the main power switch, open the front left cover

and make sure that the AC power switch is turned on.

• Application icons appear on the [Home] screen as the applications start running.

• When disconnecting the power cord from the wall outlet, always pull the plug, not the cord.

Pulling the cord can damage the power cord. Use of damaged power cords could result in ﬁre

or electric shock.

1. Open the main power switch cover, and then push the main power switch.

The main power indicator goes out. The main power turns off automatically when the machine shuts

down. If the screen on the control panel does not disappear, contact your service representative.

Saving Energy

This machine has the following energy saving functions.

Fusing Unit Off mode

If you do not use the machine for a certain period after an operation, the machine makes a clicking

sound and enters Fusing Unit Off mode.

When the machine is in Fusing Unit Off mode, the display is on but the fusing unit heater is off to

save energy. In this mode, you can change the machine's settings on the control panel. However,

the machine must exit this mode to print.

You can change the amount of time that the machine waits before switching to Fusing Unit Off

mode under [Fusing Unit Off Mode (Energy Saving) On/Off]. For details, see "System Settings",

Device Management.

•

Do not turn off the power while the machine is in operation.

Do not hold down the main power switch while turning off the main power. Doing so forcibly turns

off the machine’s power and may damage the hard disk or memory and cause malfunctions.

To exit Fusing Unit Off mode, start print jobs.

The time required to return from Fusing Unit Off mode and resume printing is as long as the time

required for warm-up time. For details about the warm-up time.

CIP Training Pro C7200 series

Throughput

Low Power mode

• Press the [Check Status] key

Sleep mode

If you do not use the machine for a certain period after an operation, the display will turn off and

the machine goes into Low Power mode. The machine uses less electricity in Low Power mode.

You can change the amount of time that the machine waits before switching to Low Power mode

under [Low Power Mode Timer]. For details, see "System Settings", Device Management.

You can change the machine's settings to enter Low Power mode when you press the [Energy

Saver] key. For details, see "System Settings", Device Management.

To exit Low Power mode, do one of the following:

• Press the [Energy Saver] key

• Press the [Check Status] key

If the machine remains inactive for a speciﬁed period or the [Energy Saver] key is pressed, it enters

Sleep mode to further reduce the electricity it consumes. For details, see "System Settings", Device

Management.

When the machine is in Sleep mode, only the [Energy Saver] key and the [Check Status] key are

usable. The machine can print jobs from computers.

You can change the amount of time that the machine waits before switching to Sleep mode under

[Sleep Mode Timer]. For details, see "System Settings", Device Management.

To exit Sleep mode, do one of the following:

• When the machine is in Low Power mode, the [Energy Saver] key is lit. In Sleep mode, the [Energy

Saver] key ﬂashes slowly. In Fusing Unit Off mode, the [Energy Saver] key is not lit.

• The energy saving functions will not operate in the following cases:

• When ﬁxed warm-up is in progress

• When operations are suspended during printing

• When a warning message appears (The machine enters Fusing Unit Off mode unless the

cover is open.)

• When paper is jammed (The machine enters Fusing Unit Off mode except when the cover is

open.)

• When the Data In indicator is lit or ﬂashing

CIP Training Pro C7200 series

Adding/Replacing Toner bottles

Throughput

1. Open front upper right cover.

2. Push the bottle lever at the bottom,

and then pull out the toner bottle.

3. Take the new bottle out of the box.

Turn it end on end ﬁve or six times.

4. Remove the cap (place it on the

empty bottle if replacing).

CIP Training Pro C7200 series

Adding/Replacing Toner bottles

Throughput

5. Insert NEW bottle until lever clicks.

6. Close the Toner Bottle cover.

45,000 sheets per 1,482 g bottle of black toner

45,000 sheets per 1,482 g bottle of cyan toner

45,000 sheets per 1,482 g bottle of magenta toner

45,000 sheets per 1,482 g bottle of yellow toner

Note: All CMYK toner yields are measured with the A4/8.75% coverage chart, based on 50 pages per job

and 80% duplex printing.

136,000 sheets per waste toner bottle

Note: Based on A4/70% colour rate, 35% colour coverage, 6% black and white.

Supply Yields

https://www.ricoh.com.au/support/my-device/recycle

Recycle: Ricoh consumable recycling

Our consumable recycling program is free to our customers as part of our goal to reach zero

waste-to-landll. Setting the industry benchmark, the program has recycled over 1,104 tonnes

of toner cartridges. The program includes a free pickup service for qualifying customers and

a Reply Paid return service.

CIP Training Pro C7200 series

Paper path and clearing misfeeds

Throughput

Removing Jammed Paper

• Some of this machine's internal components get very hot. For this reason, take care when

removing misfed paper. Not doing so could result in burns.

• Keep your hands clear of the booklet ﬁnisher tray when removing misfed paper, pulling out or

pushing in the ﬁnisher's staple unit. You can trap and injure your ﬁngers if you do not.

• When removing jammed paper, make sure not to trap or injure your ﬁngers.

• Keep your hands clear of the inside of the ring binder and the space under the ring binder tray.

You can trap your ﬁngers if you do not.

Locating jammed paper

A misfeed has occurred in the place corresponding to the letter displayed on the control panel.

Open the front cover at the location indicated by the displayed letter, and check for a paper jam. If a

lamp is lit, open the guide plate at the location indicated by the lamp, and check for a paper jam.

• When removing paper misfeeds, do not turn off the power. If you do, the conﬁgured functions and

values will be lost.

• To prevent paper misfeeds, do not leave any torn scraps of paper inside the machine.

DWP558

CIP Training Pro C7200 series

Paper path and clearing misfeeds

Throughput

Procedure for removing jammed paper

1. Remove the jammed paper by following the procedures that are displayed on the control

panel.

When [Previous] or [Next] is displayed, press [Next] after completing a procedure.

2. When the jammed paper is removed, restore the machine to the original state.

• If "D" is displayed and you cannot remove the misfed paper from the right side of the fusing unit,

use the knob located on the inside of the left front cover.

1. Pull out the knob located on the inside of the left front cover.

2. Align the knob with the slot on the fusing unit, and then insert it.

CIP Training Pro C7200 series

Andere Handbücher für PRO C7200

Inhaltsverzeichnis

Andere Ricoh Drucker Handbücher

Ricoh

Ricoh Aficio 1035 Series Bedienungsanleitung

Ricoh

Ricoh Aficio SP C430DN Handbuch

Ricoh

Ricoh Aficio SP 3400SF Kurzanleitung

Ricoh

Ricoh MP C6502SP Kurzanleitung

Ricoh

Ricoh D683 Kurzanleitung

Ricoh

Ricoh Aficio AP610 Betriebsanleitung

Ricoh

Ricoh CI5040 Kurzanleitung

Ricoh

Ricoh Supervisor-I Bedienungsanleitung

Ricoh

Ricoh Pro C9500 Montageanleitung

Ricoh

Ricoh Priport DX 4640PD Service-Handbuch

Ricoh

Ricoh CL2000N - 420116 Color Laser 16.9PPM Network... Betriebsanleitung

Ricoh

Ricoh G1168604A Bedienungsanleitung

Ricoh

Ricoh SP3 Service-Handbuch

Ricoh

Ricoh InfoPrint 1585n Bedienungsanleitung

Ricoh

Ricoh P 501 Bedienungsanleitung

Ricoh

Ricoh AP410 Bedienungsanleitung

Ricoh

Ricoh Pro L5160 Bedienungsanleitung

Ricoh

Ricoh Priport DX 4640PD Bedienungsanleitung

Ricoh

Ricoh C7528 Bedienungsanleitung

Ricoh

Ricoh FW870 Bedienungsanleitung

Ricoh

Ricoh Aficio SP 3500N Montageanleitung

Ricoh

Ricoh MFSP213SFNW1 Bedienungsanleitung

Ricoh

Ricoh CL7000 - Aficio D Color Laser Printer Bedienungsanleitung

Ricoh

Ricoh SP C250SF Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung