10
COMPRESSOR ON PSI:
The compressors can be congured to turn on anytime the pressure drops
below 125 to 140psi. Setting the turn on pressure higher will make the
compressors run more often, but for a shorter length of time. Setting the turn
on pressure lower will make the compressors run less often, but they will run
for a longer amount of time.
SYSTEM ACCURACY:
The System Accuracy feature allows the user to choose how precise the system
is when attempting to reach a preset destination. This feature satises all
drivers (some like to wait for the system to reach preset before driving away
while others want to start the car, throw it in drive and take o)
STANDARD: The vehicle will reach the preset destination in as few operations
as possible. This is acceptable for most applications.
MEDIUM: The system will be slightly more precise than the Standard setting
which means it will take a few more steps to reach a more precise target.
HIGH: This is the most accurate the system can be. It will take longer to reach
the preset destination, but you can be assured that the vehicle is at the exact
preset height.
PRESET SETTINGS:
Should you ever need to know the values that are saved for the three preset
settings they can be accessed here.
If you are using an air only system you will only see pressure readings for each
air spring.
If you are using an air and level sensor system you will see both air pressure
readings as well as level sensor voltage readings.
RERUN SETUP:
Should you ever need to recalibrate the system you may do so by rerunning the
setup procedure.
When you choose to rerun the setup you will be asked:
“ARE YOU SURE YOU WANT TO RERUN SETUP?”
You may select YES by pressing the “1” button, or select NO by pressing the “3”
button.
BACKUP ECU:
Upon initial installation the E3 system had you go through a calibration
exercise. This calibration saved information about your vehicle such as how
quickly the vehicle inates and deates, how often the compressors run, etc.
Should you ever need to change ECU’s you can back up the calibration data
from the ECU to the display so you don’t have to go through calibration again.
RESTORE ECU:
Once you have saved the calibration data using the “Backup ECU” feature you
can use the Restore ECU feature to load a new ECU with calibration data from
the old ECU.
SYSTEM INFO:
This is where you nd the software revision of both the display and ECU as well
as a volt meter to aid in troubleshooting.
DISPLAY SWVER: This is the software version that is loaded into the display.
ECU SW VER: This is the software version that is loaded into the ECU.
VOLTS: This is a digital voltmeter that will show you the voltage of the vehicle.
AUTO LEVEL
The Auto Level on Start feature is used to raise the vehicle to the #2 Preset each
time the ignition is turned on.
ON:
When vehicle is started it will return to the #2 Preset.
OFF:
When vehicle is started it will not automatically adjust to any setting
Menu Options - Details
TIME OUT FEATURE:
The display screen and button backlights can remain illuminated at all times, or
if you wish they can turn o after some time.
OFF: The display will remain on as long as the ignition is on.
30 SECONDS: The display will remain illuminated for 30 seconds.
60 SECONDS: The display will remain illuminated for 1 minute.
120 SECONDS: The display will remain illuminated for 2 minutes.
300 SECONDS: The display will remain illuminated for 5 minutes.
SCREEN INTENSITY:
The intensity of the display screen backlighting can be automatically adjusted
depending on ambient light conditions, or it can be changed to 3 intensity
levels.
AUTO: The backlight intensity will change with ambient light conditions.
LOW INTENSITY: The backlighting will remain at the lowest intensity.
MID INTENSITY: The backlighting will remain at a medium intensity.
MAX INTENSITY: The backlighting will remain at the brightest setting.
KEYPAD INTENSITY:
The intensity of the button backlighting can be automatically adjusted
depending on ambient light conditions, or it can be changed to 3 intensity
levels.
AUTO: The backlight intensity will change with ambient light conditions.
LOW INTENSITY: The backlighting will remain at the lowest intensity.
MID INTENSITY: The backlighting will remain at a medium intensity.
MAX INTENSITY: The backlighting will remain at the brightest setting
DISPLAY OPTIONS
Display Options allows you to change items such as the brightness of the screen or buttons as well as how long the screen will remain illuminated. OPTIONS
SYSTEM SETUP
System Setup allows you to change items such as system accuracy and compressor turn on pressure. You can also view system information such as preset
settings and software revision.
DYNAMIC LEVELING:
Dynamic Leveling will automatically raise or lower the vehicle back to the #2
Preset if the load changes while the vehicle is parked. As soon as the vehicle is
in motion the system stops adjusting as it’s unsafe to alter air spring pressure
while driving.
ON:
The vehicle will return to the #2 Preset if the load changes.
OFF:
The vehicle will not adjust if the load changes.
