Riello NetMan 202 plus Bedienungsanleitung

0MNACCSA3ENUC

- ENGLISH -

- 2 -

INTRODUCTION

Thank you for choosing our product.

The accessories described in this manual are of the highest quality, carefully designed and built in

order to ensure excellent performance.

This manual contains detailed instructions on how to install and use the product.

It should be kept with care near the NetMan Plus, so that it can be consulted for information

on how to use and make the most of your device. IT SHOULD BE READ BEFORE YOU

START WORKING ON THE DEVICE.

Symbols used in this manual:

Warning

Indicates important information that must not be ignored.

Information

Provides notes and useful suggestions for the User.

SAFETY

This part of the manual contains SAFETY precautions that must be followed scrupulously.

The device has been designed for professional use and is therefore not suitable for use in

the home.

The device has been designed to operate only in closed environments. It should be

installed in rooms where there are no inflammable liquids, gas or other harmful substances.

Take care that no water or liquids and/or foreign bodies fall into the device.

In the event of a fault and/or impaired operation of the device, do not attempt to repair it but

contact the authorized service centre.

The device must be used exclusively for the purpose for which it was designed. Any other

use is to be considered improper and as such dangerous. The manufacturer declines all

responsibility for damage caused by improper, wrong and unreasonable use.

- ENGLISH -

- 3 -

ENVIRONMENTAL PROTECTION

In the development of its products, the company devotes abundant resources to analysing the

environmental aspects.

All our products pursue the objectives defined in the environmental management system

developed by the company in compliance with applicable standards.

No hazardous materials such as CFCs, HCFCs or asbestos are used in this product.

When evaluating packaging, the choice of material has been made favouring recyclable materials.

Please separate the different material of which the packaging is made and dispose of all material in

compliance with applicable standards in the country in which the product is used.

DISPOSING OF THE PRODUCT

The device contains electronic PCBs and batteries which are considered TOXIC. When the

product reaches the end of its operating life, dispose of it in accordance with applicable local

legislation.

Disposing of the product correctly contributes to respecting the environment and personal health.

The manufacturer reserves the right to modify the product described in this manual at any time and

without notice.

- ENGLISH -

- 4 -

CONTENTS

PRESENTATION __________________________________________________ 6

DESCRIPTION __________________________________________________________6

OPENING THE PACKAGING AND CHECKING THE CONTENTS __________________________7

NETWORK PORT ________________________________________________________8

MICRO-USB COMMUNICATION PORT __________________________________________8

NETWORK SERVICES _____________________________________________________8

SSH_____________________________________________________________________ 8

Serial network ____________________________________________________________ 8

Wake-on-LAN_____________________________________________________________ 8

HTTP____________________________________________________________________ 9

SNMP ___________________________________________________________________ 9

UDP_____________________________________________________________________ 9

Modbus _________________________________________________________________ 9

FTP ____________________________________________________________________ 10

Email___________________________________________________________________ 11

Reports_________________________________________________________________ 12

UPS VALUES AND EVENTS HISTORY LOG ARCHIVE _______________________________13

Eventlog________________________________________________________________ 13

Datalog_________________________________________________________________ 14

ENVIRONMENTAL SENSORS (OPTIONAL)_______________________________________15

Available sensors ________________________________________________________ 15

INSTALLATION AND CONFIGURATION ______________________________ 16

INSTALLATION OF NETMAN 202 PLUS ________________________________________16

CONFIGURATION _______________________________________________________16

Configuration via USB ____________________________________________________ 16

Configuration via ssh _____________________________________________________ 16

Saving the configuration and applying the changes____________________________ 17

Start menu ______________________________________________________________ 17

Main configuration menu __________________________________________________ 18

IP config menu __________________________________________________________ 21

Time setting menu _______________________________________________________ 22

- ENGLISH -

- 5 -

Scheduled NTP menu_____________________________________________________ 24

UPS config menu ________________________________________________________ 25

Services 1 menu _________________________________________________________ 26

SNMPv1 config menu _____________________________________________________ 27

SNMPv1 community menu_________________________________________________ 27

Email config menu _______________________________________________________ 28

Email logic menu_________________________________________________________ 29

Miscellaneous menu______________________________________________________ 30

Activation 1 menu________________________________________________________ 31

Services 2 menu _________________________________________________________ 31

Wake-On-LAN address menu_______________________________________________ 32

Wake-On-LAN delay menu _________________________________________________ 32

Activation 2 menu________________________________________________________ 33

Sensors Config menu_____________________________________________________ 33

I/O Sensors menu ________________________________________________________ 35

Threshold sens menu_____________________________________________________ 36

Security menu ___________________________________________________________ 37

Save and load menu ______________________________________________________ 39

Expert mode ____________________________________________________________ 39

Configuration of several devices____________________________________________ 43

MONITORING WITH HTTP_________________________________________________43

View HTTP ______________________________________________________________ 44

Setup HTTP _____________________________________________________________ 45

MODBUS TCP/IP PROTOCOL ______________________________________________48

FIRMWARE UPDATE _____________________________________________________53

TECHNICAL DATA________________________________________________ 54

SPECIFICATIONS FOR THE CABLING OF THE NETWORK CABLE _______________________54

TECHNICAL SPECIFICATIONS_______________________________________________54

- ENGLISH -

- 6 -

PRESENTATION

DESCRIPTION

NetMan 202 plus is a device that allows UPS management through a LAN (Local Area Network);

the accessory supports all the main network protocols (SNMP v1 and v3, TCP/IP, HTTP and so

on) and is compatible with Ethernet 10/100Mbps IPv4/6 networks. The UPS can therefore be

integrated easily into medium and large-sized networks.

The device also records UPS values and events in the history log archive.

NetMan 202 plus

A: network port;

B: LED

C: Reset button

D: USB terminal

E: USB (reserved)

F: Serial (reserved)

- ENGLISH -

- 7 -

OPENING THE PACKAGING AND CHECKING THE CONTENTS

After opening the packaging, first check the contents.

The packaging should contain:

NetMan 202 plus

USB cable

- ENGLISH -

- 8 -

NETWORK PORT

NetMan plus connects to 10/100 Mbps Ethernet networks by means of connector RJ45 (see

paragraph “Specifications for the cabling of the network cable”). The LEDs built into the connector

describe the status of the network:

Left LED:

1. on and yellow if the 10/100Mbps mode link is present

2. on and green if the 10Mbps mode link is present

Right LED:

1. on and yellow during transmission in full-duplex mode

2. on and green during transmission in half-duplex mode

MICRO-USB COMMUNICATION PORT

NetMan plus makes available an usb communication port through which it is possible to configure

NetMan plus (see paragraph “Configuration via RS-232 serial line”)

NETWORK SERVICES

NetMan plus implements a series of services based on the main network protocols. These services

can be activated or deactivated according to requirements (see paragraph “Configuration”). A brief

description for each of these is given below.

SSH

By means of a ssh client (available on all the main operating systems) a remote connection with

NetMan plus can be established to change its configuration (see paragraph “Configuration via

ssh”).

Serial network

It’s possible to enable a network connection together with Serial network compatible software (for

example UPSTools) for UPS event log download.

Wake-on-LAN

NetMan plus can send “Wake-on-LAN” command for remote computers boot.

- ENGLISH -

- 9 -

HTTP

Using the HTTP (Hyper Text Transfer Protocol), is possible to configure the NetMan plus and the

status of the UPS can be monitored by means of a web browser without having to install additional

software (see paragraph “Monitoring with HTTP”). All the most popular web browsers are

supported.

SNMP

SNMP (Simple Network Management Protocol) is a communication protocol that allows a client

(manager) to make requests to a server (agent). NetMan plus is an SNMP agent.

To exchange information, manager and agent use an addressing technique called MIB

(Management Information Base). There is an MIB file for each agent, defining which variables can

be requested and the respective access rights. The agent can also send messages (TRAP) without

a prior request from the manager, to inform the latter of particularly important events. SNMPv3 is

the evolution of SNMP and introduces new important features related to security. (See paragraph

“SNMPv3”).

UDP

UDP (User Datagram Protocol) is a low level network protocol that guarantees speed in the

exchange of data and low network congestion. It is the protocol used by the UPSMon software for

monitoring and control of the UPS.

The UDP connection uses the UDP 33000 port by default but can be configured on other ports

according to requirements.

Modbus

The UPS status can be monitored by means of the standard network protocol MODBUS TCP/IP.

This service is always active on the TCP port 502. The supported function are listed on section

“Modbus TCP/IP protocol”, together with the accessible registers.

- ENGLISH -

- 10 -

FTP

FTP (File Transfer Protocol) is a network protocol used for file exchange. NetMan plus uses this

protocol for two purposes:

1. download of files of the UPS values and events history log archive (Datalog and

Eventlog) with user “user”

2. download and upload of configuration files

3. firmware upgrade

In both cases a client FTP is required, configured with these parameters:

Host: hostname or NetMan plus IP address

User: see chapter “Users”

Password: current password (default configuration: “password”)

The connection can also be established using a web browser (all the most popular web browsers

are supported), by inserting the following address: ftp://user@<address.NetMan plus>, where

<address.NetMan plus> is replaced with the device’s real address. In this case a screen like the

following will be displayed.

Example of FTP connection

Inhaltsverzeichnis

Andere Riello Adapter Handbücher

Riello

Riello MultiCOM 301 Bedienungsanleitung

Beliebte Adapter Handbücher anderer Marken

PCB Piezotronics

PCB Piezotronics 090B274 Bedienungsanleitung

Auvidea

Auvidea J20 Produkthandbuch

Gossen MetraWatt

Gossen MetraWatt AT3-III E Bedienungsanleitung

Akribis

Akribis ITF-21-BISS-MIT Bedienungsanleitung

Tenda

Tenda W54U Bedienungsanleitung

ROHO

ROHO AGILITY Bedienungsanleitung

PROLiNK

PROLiNK WN2001 Bedienungsanleitung

Hawking

Hawking HUF2 Bedienungsanleitung

Airlink101

Airlink101 AWLC4030 Bedienungsanleitung

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Bedienungsanleitung

Philips

Philips SWA4554S/10 Bedienungsanleitung

JVC

JVC TS-C9D2B Gebrauchsanweisung

NETGEAR

NETGEAR A6100 Bedienungsanleitung

D-Link

D-Link DWA-121 Bedienungsanleitung

Philips

Philips SWA2037 Bedienungsanleitung

Basalte

Basalte 0610-20 Bedienungsanleitung

Yealink

Yealink EHS40 Bedienungsanleitung

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Bedienungsanleitung