Riello GAS 6/2 Kurzanleitung

Installation, use and maintenance instructions

2915868 (5) - 07/2015

Forced draught gas burner

Two stage operation

CODE MODEL TYPE

3752482 GAS 6/2 524 T80

Declaration of conformity in accordance with ISO / IEC 17050-1

Manufacturer: RIELLO S.p.A.

Address: Via Pilade Riello, 7

37045 Legnago (VR)

Product: Forced draught gas burner

Model: GAS 6/2

These products are in compliance with the following Technical Standards:

EN 676

EN 12100

and according to the European Directives:

MD 2006/42/EC Machine Directive

LVD 2006/95/EC Low Voltage Directive

EMC 2004/108/EC Electromagnetic Compatibility

The quality is guaranteed by a quality and management system certified in accordance with UNI EN ISO 9001.

Legnago, 21.05.2015 Executive General Manager

RIELLO S.p.A. - Burner Department Research & Development Director

RIELLO S.p.A. - Burner Department

Mr. U. Ferretti Mr. F. Comencini

5868

TECHNICAL DATA

ELECTRICAL DATA

BURNER DESCRIPTION

STANDARDS EQUIPMENT

ACCESSORIES

• RADIO DISTURBANCE PROTECTION KIT code 3010386

If the burner is installed in places particularly subject to radio disturbance (emission of signals exceeding 10

V/m) owing to the presence of an INVERTER, or in applications where the length of the thermostat

connections exceeds 20 metres, a protection kit is available as an interface between the control box and the

burner.

Thermal output 2

stage 520 - 1050 kW - 447.200 - 903.000 kcal/h

Operation Two stages, high and low flame

Fuel Natural gas Pci 8 - 10 kWh/m

= 7000 - 8600 kcal/m

Minimum gas pressure For maximum output 12.3 mbar are needed measured at the coupling with

nil pressure in the combustion chamber and gas with calorific value of

8600 kcal/m

Maximum gas pressure 150 mbar

Electrical supply 3N ~ 380V - 60 Hz

Fan motor rpm

3500

220/380

1.5

5.5 - 3.2

Ignition transformer V1 - V2

I1 - I2 220 V - 1 x 8 kV

1.8 A - 30 mA

Electrical power consumption kW max 1.9

Quantity Description

1 Flange

1 Gasket

8 Screws

1 Flange gasket

1 Pipe fitting for gas train

1– Air damper controlling motor

2– Control box re-set button

3– Fair leads

4– Wiring terminal block

5– Re-set push-button of the

motor overload relay

6– Air pressure switch

7– Gas pressure test-point Fig. 1

S7530

5868

OVERALL DIMENSIONS

FIXING TO THE BOILER

FIRING RATE

COMBUSTION CHAMBER PRESSURE 2nd STAGE OUTPUT

(in compliance with DIN 4788)

Min. output at 1

stage: 300 kW - 258.000 kcal/h.

Boiler front-plate

drilling

Length available with special blast tube to be separately required.

Burner

195

185 M12

410 770227

360

485

131

370

195

ø 175

Rp 2

S7515 S7520

D1785

Separate the combustion head from the

burner body by loosening the screws 1)

and 2) and withdrawing the group A) from

the holding bars 3).

Fix the group B) to the boiler front plate 4)

using the gasket 5) provided as accessory.

2 3 5 4

A B

S7499

kcal/h

mbar

D1795

5868

MINIMUM GAS PRESSURE - OUTPUT

Pressure: detected at the pressure test-point 7) (fig. 1) with nil mbar into the combustion chamber.

Should the combustion chamber be pressurized, the pressure necessary will be that of the

graph plus the pressurization value.

Example: to obtain 800 kW it is necessary a gas pressure of 11 mbar and the combustion head set

as indicated at page 8.

If the combustion chamber is pressurized at 2 mbar, the pressure detected at the test-

point 7) is: 11 + 2 = 13 mbar.

If this value is too high, for very low gas pipework pressures, the gas gear 6) (page 8)

could be more open.

Do not decrease the pressure at the coupling under the values shown in the diagram.

Output: the maximum value is obtainable with gas Pci 8600 kcal/m

CORRELATION BETWEEN GAS PRESSURE AND BURNER OUTPUT

GAS SUPPLY

kcal/h

mbar

D1796

8 11 5

94 3 12 2 1

S7534

1- Gas pipe line 7- Gas safety shut off valve

2- Cock valve 8- 1

stage gas shut off valve

3- Filter 9- 2

stage gas shut off valve

4- Pressure stabilizer 10 - Burner

5- Pressure test-point 11 - Gas leak control device

6- Minimal gas pressure switch 12 -Isolator joint

5868

BURNER ELECTRICAL WIRING

(carried out in the factory)

CMV Fan motor contactor

F1 Protection against radio interference

K1 Relay

MB Burner terminal strip

MV Fan motor

PA Air pressure switch

RMG Control box

RT Thermal overload

SM Servomotor

SO Ionisation probe

TA Ignition transformer

TB Burner earth

TTENTION

In the case of phase-phase feed, a

bridge must be fitted on the control box

terminal board between terminal 6 and

the earth terminal.

20107484

5868

ELECTRICAL CONNECTIONS TO THE WIRING TERMINAL BLOCK

(to be carried out by the installer)

NOTICE

- The electric wiringcarried out bythe installer must bein compliancewith the rules in force in the Country.

- Leads minimal section 1 mm

- Burners with non-stop operation. For safety reasons, this type of burner must be stopped every 24

hours of operation, by means of an hours-counter to be connected in series with the adjustment

devices.

FLAME MODULATION

The flame modulation is obtainable through the thermostat, controlling the second valve, connected

to the terminals 10 and 11.

2662

HRemote lock-out signal

H1 Remote lock-out signal of leak detection control device

Burner terminal strip

PG Minimum gas pressure swicth

TL Limit control device system

stage remote control system

TS Safety control device system

VS Gas safety shut off valve

VPS Leak detection control device

stage gas shut off valve

XP7 Plug for leak detection control device

220V 380V

F Ampere T16 T10

S mm

1,5 1,5

5868

FIXING OF THE ELECTRICAL WIRES

All the electrical wires, which are to be connected to

the terminal block 4) (fig. 1) shall pass through the fair

leads 3) (fig. 1) as for this scheme.

1 - Three phase supply :fair lead Pg 21

2- Single phase supply : fair lead Pg 13.5

3- Adjustment thermostat : fair lead Pg 13.5

4- Safety thermostat : fair lead Pg 13.5

5- Gas train : fair lead Pg 13.5,

sheath ø 13

6-2

stage thermostat : fair lead Pg 13.5

7 / 8 - Pre-sheared holes

Further prospective signals or controls can be connected to the burner wiring terminal board by

removing the metal weldnuts from the pre-sheared holes and inserting a commun fair lead for the

passage and the clamping of the leads.

NOTES

- Do not exchange the neutral wire with the phase (avoid the plug-pin connection).

- Carry out a safe earth connection.

- Check the stop of the burner, by opening the boiler thermostat and the burner lock-out, by

disconnecting the lead from the flame probe.

WARNING

When closing the burner on its slide-bars, pull towards the outside the high voltage cable and the

cable of the flame detection probe, till to little tension.

BURNER START-UP CYCLE

Air-purge: loosen the screw placed on the

minimal gas pressure switch mounted on the

gas train

AIR PRESSURE SWITCH

The air pressure switch 6)(fig. 1) setting shall

be carried out after having set all other adjust-

ments of the burner and the air pressure

switch shall be at its lowest set-point.

When the burner is operating, increase the

adjustment pressure by turning - slowly -

clockwise the knob till reaching the burner

lock-out.

Thereafter, turn the knob anticlockwise for 1

mbar and repeat the burner start-up for

checking the regularity: if lock-out intervenes

turn the knob anticlockwise for 0.5 mbar.

S7535

Screw

Plug for pressure

Pressure switch

S7506

measure

1 ÷ 10

mbar

Adjustment knob

S7507

5868

PROBE - IGNITION ELECTRODE POSITION

CAUTION:

do not turn the ionization probe, maintain the drawing position; should it be close to the ignition

electrode, damage may occur to the control box amplifier.

COMBUSTION HEAD ADJUSTMENT

Two separate adjustments have to be made: air and

gas.

These adjustments can be carried out when the burn-

er is still open, during the installation (see page 2 -

Fixing to the boiler).

Air setting

Loosen the two screws 1) and move the internal part of

the combustion head 2) so that its rear edge 3) is coin-

cident with the desired set-point on the plate 4). Tighten

the screws 1).

Gas setting

Loosen the screw 5), move the ring 6) so that the point-

er 7) is coincident with the desired set-point 8). Tighten

the screw 5).

Attention:

the set-point number is the same for air and gas setting

and is given by the following diagram.

Example:

the burner is installed on a boiler

of 810 kW, assuming an efficiency

of 90% the burner output should

be 900 kW.

From the diagram it can be seen

that the air and gas settings for

this rating should be no. 5.

3 - 4 mm

2 - 4 mm

Probe position Ignition electrode position

S7524

1 3 4 7

S7496

kcal/h kW

Burner output

Set-point number = for air and gas

D1797

5868

COMBUSTION CHECKS

It is advisable to not exceed 10% of CO

(gas with calorific value of 8600 kcal/m

), in order to avoid

the risk that small changes of the adjustments due, for instance, at draught variation, may cause com-

bustion with insufficient air and consequently formation of CO.

For safety reason the value of 0.1% (one thousand p.p.m.) must not be exceeded.

IONIZATION CURRENT

The minimum current necessary for the control box operation is 3 µA.

The burner normally supplies a higher current value, so that no check is needed.

However, if a measurement of the ionization current is required, it is necessary to disconnect the

probe lead and insert a d.c. microamperometer.

MOTOR LOCK-OUT

This is caused by the terminal protector relay, in case of overloading, or by the lacking of the

phase. To clear, pushdown the appropriate knob, after having removed the protective cover.

BURNER START-UP

If during operation the flame shuts off, lock-out occurs within 1 sec

+ -

Lead Probe

S7511

Normal Lock-out because no ignition

Thermostat

Motor

Ignition transf.

valve

flame

valve

2 s 40 s 10 s 2 s 40 s 3 s max.

D1799

flame

Lock-out

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Riello Brenner Handbücher

Riello

Riello GI/EMME 300 Kurzanleitung

Riello

Riello RS 250/EV MZ Kurzanleitung

Riello

Riello GAS 8 P/M Kurzanleitung

Riello

Riello RS 160/M BLU Kurzanleitung

Riello

Riello RL 190 Kurzanleitung

Riello

Riello DB16 LSM C13 Kurzanleitung

Riello

Riello G5R MC Kurzanleitung

Riello

Riello 970 T80 Kurzanleitung

Riello

Riello RLS 300/BP MX Kurzanleitung

Riello

Riello Gulliver RG1RK Kurzanleitung

Riello

Riello P 140P/NA Kurzanleitung

Riello

Riello RX 2500 S/E Kurzanleitung

Riello

Riello RN 28 Kurzanleitung

Riello

Riello RS 55/E BLU Kurzanleitung

Riello

Riello RLS 28 Kurzanleitung

Riello

Riello RS 64/M MZ Kurzanleitung

Riello

Riello RL 100/E Kurzanleitung

Riello

Riello RS 25/E BLU Kurzanleitung

Riello

Riello RS5F Kurzanleitung

Riello

Riello DB 4 LSM C13 Kurzanleitung

Riello

Riello 40 G3RD MC Kurzanleitung

Riello

Riello RS 50 Kurzanleitung

Riello

Riello RL 55/M BLU Kurzanleitung

Riello

Riello RLS 810/E FGR Kurzanleitung

Beliebte Brenner Handbücher anderer Marken

True Induction

True Induction TI4B Bedienungsanleitung

Weishaupt

Weishaupt WG20 Series Bedienungsanleitung

Carolina Cooker

Carolina Cooker M116672 Bedienungsanleitung

Unigas

Unigas HTP2000 Bedienungsanleitung

baltur

baltur BT 250 DSG 4T Bedienungsanleitung

muenkel design

muenkel design round burner Bedienungsanleitung

Ecoflam

Ecoflam Multicalor 170.1 Bedienungsanleitung

baltur

baltur BT 14 DSGW Bedienungsanleitung

artisan

artisan Art-SB1 Leitfaden

AESYS

AESYS TurboFire II Bedienungsanleitung

IKEA

IKEA GRILLSKÄR Bedienungsanleitung

RUSTA

RUSTA SAREK Bedienungsanleitung

PROPOINT

PROPOINT 8933657 Bedienungsanleitung

baltur

baltur TBL 1000 ME Referenzhandbuch

Riello Burners

Riello Burners P 200 P/G Kurzanleitung

WLD-TEC

WLD-TEC powerjet Bedienungsanleitung

MSR

MSR DRAGONFLY Bedienungsanleitung

baltur

baltur COMIST 23SP Bedienungsanleitung