Riello BeSMART Bedienungsanleitung
EN Quick Start Guide
BeSMART Wi-Fi Thermostat
1The installation is made in 3 steps
B C
Install the BeSMART thermostat Install the Wi-Fi box Download the BeSMART App
A
Preparation
Before installation
•Refer to the appliance manual to ensure that the BeSMART thermostat is compatible with your
boiler
•The BeSMART wireless thermostat can be installed almost everywhere within the home, however
please refer to the adjacent diagrams for guidance when deciding on a suitable location.
•The BeSMART thermostat can also be used to replace an existing hard-wired thermostat (please
check appliance manual to ensure compatibility).
•Switch off and isolate the appliance and any external controls from the electrical supply, before
carrying out the installation.
Tools required for the installation
•Phillips screwdriver
•Small flat blade screwdriver
•Combination pliers
Avoid draughty areas Do not install above heat sources
Avoid direct sunlight Install at the correct height
2
BeSMART Installation
A
3
If necessary remove the old thermostat.
Attention: The BeSMART thermostat is a wireless
control. Isolate any redundant wiring and ensure it
does not interfere with the fitment of the BeSMART
control. If its intended to re-use any existing wiring; you
should refer to the appliance manual to ensure
compatibility .
Separate the BeSMART from the wall plate.
Fix the wall plate to the wall
using the supplied screws.
(screw head inside proper
location)
Hard-wired installation
If using as a hard-wired control; connect the respective wiring to
the relevant terminals on the BeSMART control.
TA
ON/OFF
Attention: Please refer to the appliance
installation manual and the BeSMART
manual for specific information on hard-wired
connections.
BeSMART Installation
A
4
Re-attach the BeSMART thermostat to the wall plate by
aligning and then pressing firmly around the outer edges.
Attention: insert the batteries, observing
the correct polarity as indicated.
Insert two ‘AA’ type batteries
(supplied), into the battery compartment .
Wi-Fi Box Installation
B
5
In the case of a wireless BeSMART installation, connect the (supplied)
USB Wi-Fi Box cable to the boiler OT-Bus connection (for specific
boilers) or to the boiler room thermostat connection (TA or ON/OFF).
Attach the Wi-Fi Box to the appliance casing, using
the magnetic pad located on the rear of the Wi-Fi
Box. Please check the ambient temperature is
according the product specification as indicated in
the installation manual. In case of installation wireless,
low Wi-Fi signal and boiler RF receiver installed, place
the Wi-Fi Box in an ambient with a good Wi-Fi signal
(above 30%).
Attention: for the electrical connection and the technical specifications, please
refer to the installation manual. (OT PCB plug supplied as standard)
USB
For a wireless installation, insert the other end
of the USB cable into the OUTPUTS/BOILER
socket of the Wi-Fi Box.
USB
USB mini B
Using the mini USB cable
and power adaptor
(supplied); connect the Wi-Fi
box to an adjacent electrical
socket .
TA = Black
OT = Red
Outputs/Boiler
C Installation and configuration of smartphone app
Download and install the
BeSMART App on a
smartphone or tablet.
6
Create a user account
following the steps indicated on
the app.
Link the user account to the ‘ID
Wi-Fi’ code that’s located on
the side of the Wi-Fi Box.
MAC : 000000000000
ID Wi-Fi : 0000000000000
Use the password key of the ‘Wi-Fi’ router to link the Wi-Fi Box to the home network using one of the methods indicated below.
SmartLink:
Press once the SmartLink button with a paper clip or similar
The green LED should be flashing rapidly
Start the smart link function on the app (Wi-Fi configuration menu)
enter the network password – Wi-Fi Box will automatically configure
WPS: (only for router with WPS functionality)
Enable the WPS function via your router/home network
Press and hold the WPS button on the WiFi box with a paper clip or similar,
until the green and red LEDs are flashing rapidly and consecutively
Successful activation is confirmed when the red LED flashes rapidly
Outputs/Boiler
WPS / Smartlink
WPS / Smartlink Outputs/Boiler
If required, it is possible to couple a boiler receiver or additional thermostats to the Wi-Fi Box
using the following procedure: press and hold the Wi-Fi LED button on the Wi-Fi Box until both
red and green LEDs are flashing simultaneously. Place the device that is to be coupled, into
the ‘coupling’ mode. When the coupling process has been completed, the system will
automatically return to the normal operating condition.
Wi-Fi LED button
The system, once online, may take up to 4 minutes for self configuration
Restart Wi-Fi router at the end
Alarms and working status
7
Alarm codes indicated on the
BeSMART display and
suggested corrective actions.
More info and technical support on the following website:
www.besmart-home.com
BeSMART is a RIELLO GROUP brand
Via Ing. Pilade Riello, 7
37045 Legnago - Italy
Explanation of status LEDs displayed on Wi-Fi Box.
LED
= fixed ON
= flashing fast (0.5 secs)
= flashing slow (1 secs)
Err
E82
E83
E84
A01….99
Temperature sensor broken.
(not reparable)
Radio frequency error.
(Batteries/distance)
NO OT-bus communication.
(check connections)
Hardware problem.
(not reparable)
Boiler alarm.
(refer to boiler manual)
LED
green
LED
red Status
Relay = bridged (only with ON/OFF installation)
Relay = open (only with ON/OFF installation)
OT-bus connection = OK (only with OT connection)
Boiler alarm (only with OT connection)
Network or RF error
WPS mode in progress (press and hold WPS button) – wait WPS signal
WPS signal detected
SmartLink mode in progress (press SmartLink button once)
RF encoding in progress (press and hold the Wi-Fi LED button)
Andere Handbücher für BeSMART
2
Andere Riello Thermostat Handbücher
Riello
Riello ricloud Bedienungsanleitung
Riello
Riello ricloud Bedienungsanleitung
Riello
Riello BeSMART Bedienungs- und Installationshandbuch
Riello
Riello Hi, Comfort 100 Bedienungs- und Installationshandbuch
Riello
Riello RiCLOUD NA Series Bedienungsanleitung
Riello
Riello BeSMART Bedienungsanleitung
Riello
Riello CDI 15 Bedienungsanleitung
Riello
Riello Hi, Comfort T100 Bedienungs- und Installationshandbuch
Beliebte Thermostat Handbücher anderer Marken
EWELLY
EWELLY EW-181 Bedienungsanleitung
Prolon
Prolon T1100 Montageanleitung
Computherm
Computherm Q20 Bedienungsanleitung
Heatmiser
Heatmiser neoStat Bedienungsanleitung
Aube Technologies
Aube Technologies TH111GFCI-NP 240 VCA Bedienungsanleitung
Mars
Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung
