RIKA V2.23 Bedienungsanleitung

Touch Display

V2.23

Operating Instructions

TABLE OF CONTENTS

1. INTRODUCTION 3

2. COMMISSIONING 3

General view of interfaces�� 3

External request�� 3

Serial interface�� 3

USB connection�� 3

First steps�� 3

3. MENU NAVIGATION 4

Navigation��4

Standard functions ��4

Cleaning function��4

Door opener�� 5

ECO function�� 5

Active info �� 5

4. OPERATING MODES 6

Manual mode��6

Automatic mode��6

Comfort mode ��6

Heating up without electrical ignition��6

5. SETTINGS 7

Heating times ��7

Multi Air fan��7

Frost protection��7

RIKA room sensor��7

RIKA ﬁrenet��7

GSM��7

Screen Saver ��7

Child lock��7

Date/time��7

Language selection��7

Resets ��7

Logging ��7

Service ��7

6. INFO 8

Inputs �� 8

Outputs �� 8

Parameters�� 8

7. EXTENDED OPERATING MODES  PELLETS  LOGS 9

Correct heating up�� 9

Automatic log operation ��9

Eco Operation�� 9

Current-free log operation��10

Combined operation ��10

Easy-reﬁlling operation��10

8. NOTES, WARNINGS AND ERROR MESSAGES 11

Notes ��11

Warnings��11

Error messages��12

1. INTRODUCTION

Our congratulations for having purchased a quality product�

To ensure a trouble-free functioning of your appliance we

recommend you to thoroughly read through the present instructions

and to strictly observe the suggestions contained herein at all times�

By cleaning and servicing your appliance regularly and expertly you

will ensure a long-lasting functioning over many years�

RIKA is always ambitious to provide an excellent service� Have a

good time, enjoying the cosy warmth of your RIKA stove as often as

you wish�

RIKA Innovative Ofentechnik GmbH

2. COMMISSIONING

General view of interfaces

External request

QExternal room thermostat*

QContactor (e�g� exhaust hood)*

* remove cable bridge and connect a 2-pin cable with a section

between 0�5 and 0�75mm2 instead�

It will take approximately 1 minutes for your stove to shut down after

receiving an external shut-down request�

Please note

Operation is not possible unless either the cable bridge, or an

external request (e�g� an external room thermostat) are connected�

The external request has priority over all operating modes

(MANUAL/AUTOMATIC/COMFORT)�

Serial interface

QRIKA room sensor/ RIKA radio room sensor (available on request)

QRIKA GSM Control (available on request)

USB connection

QFlash drive (included in the delivery)

QRIKA ﬁrenet (available on request)

First steps

Please note

Manipulations on hardware components may only be performed

by a trained expert dealer or our customer service� Inappropriate

handling of these parts will void contractual and legal warranty

claims!

Please note

The appliance may only be put into operation if fully assembled!

Before your appliance is energised for the ﬁrst time, the ﬂash drive

(included in the delivery) must be inserted into the interface provided

for that purpose at the rear side of the stove�

Install the software as described in the attached instructions�

After the unit is connected to the mains, the display changes to

Language Selection�

Français

Deutsch

English

Language Selection

Select a language� Subsequently, adjust Date and Time�

Tip

To prevent incorrect input, only the permissible digits are released

for each input step�

Date

|2016

DD MM JJJJ

The “C” button deletes the input within a selected display box�

In case of erroneous entry, depress the appropriate box to make a

new entry�

If all data have been entered correctly, an Enter button appears� By

pressing this button, the input is conﬁrmed and the data are saved�

Tip

Both language selection and setting of date and time must only be

carried out on initial operation�

USB connection

Serial interface

External request incl� cable bridge

3. MENU NAVIGATION

Your stove is equipped with a state-of-the-art control system� You

can control all functions on the intuitive touch display� The surface

of the touch display responds to both ﬁnger pressure and touch pen�

Please note

Do not use sharp-pointed objects to operate the appliance so as to

prevent damaging the surface of the touch display�

Navigation

The complete controls of your appliance include 4 main menu levels:

HOME

Controls: Unit start (stop, regulation of heating power

/ set ambient temperature, display of current stove

state, active info

OPERATING MODES

Range: Manual mode, automatic mode and comfort

mode

SETTINGS

Setting: Heating times, Multi-air, frost protection, RIKA

room sensor, ��

INFO

Display: ﬂame temperature, total operating hours, total

ignitions, software version,��

Standard functions

Each stove model provides the following standard functions:

Reducing heating

output

Increasing heating

output

Off Start / Standby

Please note

To avoid involuntary starting or switching off, either button must be

depressed for 2 seconds�

Please note

If your stove is shut off during the operating states IGNITION or

INITIAL PHASE, the display will switch toBURNOFF only after a few

minutes�

Cleaning function

In addition to the standard functions, stove models with an automatic

grid dispose of a cleaning function�

Grid turning into

cleaning position

Show additional

functions

Please note

Turning of the grid is only possible during the operating state

STOVE OFF at a ﬁrebox temperature below 80°C!

Door opener

In addition to the standard functions, some stove models dispose of

a door opening function�

Show additional

functions

Hide additional

functions

Opening the

decorative glass

door

ECO function

In addition to the standard functions, some combi stoves dispose of

an ECO function�

Show additional

functions

Hide additional

functions

Switching to the

Eco mode of

operation

Active info

The ‘Active info’ displays whether or not a module is connected or

enabled�

HEATING TIMES

Standard function

ROOM SENSOR

Only with RIKA room sensor / RIKA radio room sensor

GSM

Only with RIKA GSM Control

FROST PROTECTION

Only with RIKA room sensor / RIKA radio room sensor

RIKA ﬁrenet

Only with RIKA ﬁrenet

Please note

More detailed information on the different options can be found in

the respective instructions�

4. OPERATING MODES

In the main menu OPERATING MODES you can switch between three

different operating modes: Manual, Automatic and Comfort

Comfort Mode

Manual Mode

Automatic Mode

Mode Select 15:55

Su 16.10.2016

Manual mode

Your stove operates at a heating power preset by you�

The recommended output range is between 50 % and 100 %� If

you wish to select a lower heating output, keep pressing the minus

button for 2 seconds� Now you can set the heating output within the

range from 30 % to 50 %�

Tip

Running the stove at the recommended range from 50% to 100%

of the heating capacity will cause less sooting of the ﬁrebox and

the door glass�

Automatic mode

Your stove operates at the heating power preset by you during the

heating times, as saved� Outside the heating times your stove is in

theSTANDBY operating state�

Tip

If you select the automatic mode although no heating times are

saved, the symbol “heating times” will be ﬂashing�

Please note

The stove may only be started in the STANDBY operating state� In

the operating state STOVE OFF it is not possible to start up the

stove�

Comfort mode

During the heating times, as saved, your stove keeps a nominal room

temperature preset by you�

Outside the heating times, it is possible to adjust a setback

temperature� If the room temperature drops below the adjusted

setback temperature, your stove will start outside the saved heating

times as well�

In this operating mode, heating times may be disabled as well� In this

case, your appliance will permanently heat the room to the nominal

temperature you set�

Please note

The stove may only be started in the STANDBY operating state� In

the operating state STOVE OFF it is not possible to start up the

stove�

Please note

The comfort mode may only be selected if a RIKA room sensor is

connected�

Heating up without electrical ignition

If the ignition cartridge of the appliance should fail, ﬁrelighters can

be used to ensure an emergency operation� First, start the stove

as usual� Wait for the cleaning cycle and for the grid to tip� Then

open the ﬁrebox door and place a handful of pellets, along with the

ﬁrelighter, into the cleaned ﬁre trough and light it up, subsequently

closing the ﬁrebox door�

Please note

Attention: Do not use any ﬂammable liquids to light up the ﬁre!

5. SETTINGS

The main menu SETTINGS is provided to set, among others, the

heating times, Multi Air blower, frost protection etc�

Heating times

Using the heating times program you can operate your stove

according to the heating schedule� Activating heating times (ON)

gives access to setback temperature (only with RIKA room sensor),

and the heating times program�

Set Heating Times

Heating Times

Set Back Temp

Heating Times

15:55

Su 16.10.2016

In the heating times program, single weekdays, or a couple of

weekdays can be marked simultaneously (highlighted in ORANGE)�

Upon selecting heating time I or heating time II you can enter the ON

and OFF times you require for the marked weekdays�

Weekdays that have already been programmed are highlighted in

GREEN when re-accessing the heating times program�

Heating Time II

Heating Time I

Set Heating Times

ON OFF

##:## ##:##

Mo Tu We FrTh Sa Su

20:15 21:45

15:55

Su 16.10.2016

Tip

As soon as a weekday is marked, the saved heating times are

displayed�

If a number of weekdays are marked, only the identical heating

times are displayed� If the heating times differ from each other,

hash keys (##:##) are displayed�

Tip

If your stove does not start up although heating times have been

saved, please check if they are enabled (ON) and if your stove is in

STANDBY operating state�

Multi Air fan

Enabling the Multi Air fan (ON) you get access to fan speed and fan

adaptation�

Fan level

The volume of convection air is adjustable from AUTO (adapts

automatically according to heating power), over to Level 1 (min) and

level 5 (max)�

Fan area

In addition, it is possible to adapt the Multi Air fan speed (AUTO, level

1 to level 5) within +/- 30% of fan speed�

Frost protection

If this function is enabled (ON) and if the room temperature drops

below the set value (2°C - 10°C), your stove will start working�

This applies also outside the heating times and in operating

stateSTOVE OFF�

RIKA room sensor

For more information on this option, please consult the operating

instructions room sensor / RIKA radio room sensor� If there is a room

sensor built in you get access to temperture adjustment and power

requirement�

Temperture adjustment

It is possible to adjust the temperature shown in the infomenu�

Power requirement

(factory setting 3) The heating power is adjustable from level 1 (for

small rooms) to level 4 (for big rooms)�

RIKA firenet

For more information on this option, please consult the operating

instructions RIKA ﬁrenet�

GSM

For more information on this option, please consult the operating

instructions RIKA GSM Control�

Screen Saver

Sets the time interval (OFF, from 1 min to 30 min) for activating the

screen saver�

Child lock

If this function is enabled (ON), a 4-digit code can be saved� Now, the

screen saver may only be disabled by entering the saved code�

Date/time

Sets date and time�

Language selection

Selects the desired language�

Resets

Kg till cleaning

Resets the supply rate to 700 - 1500kg after a service has been

carried out�

Factory setting

Resets all stove settings to the factory setting�

Please note

This reset may only be performed if the stove temperature is below

80°C!

Logging

Only for service technicians�

Service

Only for service technicians�

6. INFO

In the main menu INFO you can retrieve the most important

parameters�

Parameters

Info

Input

Output

Su 16.10.2016 15:55

Inputs

Flame temperature [°C]

Current ﬁrebox temperature

Room temperature [°C]

ACTUAL temperature in the room

Ext. Request

External request enabled (ON) or disabled (OFF)

Pressure switch

Sufﬁcient low pressure in the ﬁrebox to ensure operation (OFF), or

insufﬁcient (OFF)

Grid contact

Grid in heating position (ON) or other position (OFF)

Outputs

Discharge motor [‰]

Actual speed (0 - 1000)

Discharge motor current

Actual current consumption (0 - 120)

Flue gas fan [1/s]

Actual speed (0 - 2500)

Insertion motor [‰]

Actual speed (0 - 1000)

Insertion motor current

Actual current consumption (0 - 120)

Air ﬂaps

Current position (0 - 1000)

Grid motor

Actuated (ON) or in rest (OFF)

Multi Air fan

Actuated (ON) or in rest (OFF)

Multi Air fan 2

Actuated (ON) or in rest (OFF)

Ignition element

Actuated (ON) or in rest (OFF)

Parameters

Operat. hours pellets

Total operating hours in pellet mode (0 - 99999)

Feed rate total [kg]

Total pellet feed volume (0 - 99999)

Kg till cleaning

Remaining pellets feed volume until next cleaning (1500 - 0)

Operat. h. split logs

Total operating hours in split log mode (0 - 99999)

Ignition counter

Total ignitions (0 - 99999)

ON/OFF cycles

Number of power failures

Main State

Operating state Main Regulation Sequence

Sub State

Operating state Secondary Regulation Sequence

Stove type

Name of appliance

Software stove

Software version stove controls

Software display

Software version touch display

7. EXTENDED OPERATING MODES  PELLETS  LOGS

Your combi stove features an automatic fuel recognition and a

combustion regulation� Operation may any time switch between

pellets and logs�

Please note

It is imperative to use the feed rates as indicated in the instructions

manual of your stove, without any exception�

Please note

During the whole period of log operation the functions of heating

time, room temperature and frost protection, as well as the

external request are disabled� These functions will not be re-

activatedbefore log operation has ﬁnished�

Correct heating up

Please note

Do not use any ﬂammable liquids to light up the ﬁre!

Open the ﬁrebox door and place 2 small pieces of chipboard in

longitudinal direction to either side of the ﬁrebox ﬂoor�

Place 2 or 3 logs crossways onto the chipboard�

Now place more chipboard pieces crossways and add 2-4 ribs of the

RIKA ﬁrelighter on top of the chipboard� If necessary, some uncoated

paper can be placed under the chipboard instead of the ﬁrelighter�

Now set the RIKA ﬁrelighter (or the uncoated paper) alight and close

the ﬁrebox door�

Please note

Be sure that the combustion trough is empty as the grid will tip

after the ﬁrebox door has been closed�

Tip

The RIKA ﬁrelighter no� E15718 is available from your RIKA dealer�

Automatic log operation

The automatic burn-off regulation shows the following sequence:

LOG CHECK

Your stove checks if logs have been placed�

LOG OPERATION  ECO OPERATION

Your stove ensures optimum log burn-off�

PLEASE RELOAD

Your stove indicates the time you should add more logs�

DO NOT RELOAD

Your stove reports that no ignition can be ensured after logs have

been added�

Eco Operation

For a small amount of fuel (partial load) you should use the ECO

OPERATION mode� Under ‘Extended functions’, after closing the

ﬁrebox door you can switch to ECO OPERATION - the operating state

LOG CHECK will change toECO OPERATION�

Please note

The ECO OPERATION mode is only possible after the ﬁrst burn-off!

Current-free log operation

Please note

Your stove must be disconnected from the mains for current-free

operation�

Please note

Any modiﬁcation of the procedure stated above may result in

damaging of components, which automatically will void any

warranty claims�

Insert the socket spanner supplied in the sleeve, as shown�

Turn it clockwise until a slight stop can be felt�

Remove the socket spanner from the opening and insert it again in

horizontal position�

Turn the spanner ant-clockwise until it is ﬂush with the marking in

the side panel (approx� 45°)� It is now in heating up position�

After heating-up has been successful, turn the spanner anti-

clockwise step by step to reduce the combustion air manually, thus

regulating the burn-off�

Each time logs are added, the spanner must be brought into heating

up positon again� The combustion air is regulated as described

above�

Please note

Always ensure that the stove has enough air for combustion�

Combined operation

Automatic ignition of ﬁrewood during start-up, or automatic log

recognition during operation�

Automatic ignition of ﬁrewood during start-up

Place two logs into the ﬁrebox� Be sure that at least one of the logs

lies above the combustion trough to facilitate burning� Close ﬁrebox

door�

Start stove operation� After ignition has been successful, the

operating state IGNITION switches to LOG CHECK, and after

successful log recognition toLOG OPERATION�

Please note

If no more logs are reloaded, pellet operation starts automatically

again as the unit is still on�

Automatic log detection during operation

Open the ﬁrebox door and place 2 logs into the box� Be sure that

at least one of the logs lies above the ignition trough to facilitate

burning�

Close ﬁrebox door� The operating state switches from CONTROLLED

OPERATION to LOG CHECK, and after successful log recognition

toLOG OPERATION�

Please note

If no more logs are reloaded, pellet operation restarts automatically

as the unit is still on�

If you switch the combi stove off during log operation, the operating

state will change to STOVE OFF after the logs have burned down�

Easy-refilling operation

In order to reduce the discharge of ﬂuegas when reﬁlling logs there

is a easy-reﬁlling operation available�

unhide additional

functions

hide additional

functions

Open the ﬂuegas

ﬂap

Wait about 3 seconds before you open the combustion chamber

door to refuel�

After closing the combustion chamber door, turn the wrench

clockwise to close the ﬂuegasﬂap�

Tip

If the ﬂue gas ﬂap is open, a warning appears on the display� It

expires when you close the ﬂue gas ﬂap�

Note

Pellet operation is not possible with an opened ﬂue gas ﬂap�

Andere Handbücher für V2.23

Inhaltsverzeichnis

Andere RIKA Touchscreen Handbücher

RIKA

RIKA V2.23 Bedienungsanleitung

Beliebte Touchscreen Handbücher anderer Marken

FlowLine

FlowLine Data loop Bedienungsanleitung

ALPEX

ALPEX AEx-8 P Series Bedienungsanleitung

Ltech

Ltech E5S Bedienungsanleitung

Harman

Harman AMX MODERO S MSD-701-L2 Bedienungsanleitung

Acnodes

Acnodes PC 1150 Bedienungsanleitung

AIS

AIS IP10IA99 series Bedienungsanleitung

IBASE Technology

IBASE Technology ASTUT-152-RE1S Bedienungsanleitung

YASKAWA

YASKAWA TP 610C Bedienungsanleitung

B&R

B&R Power Panel C Series Bedienungsanleitung

AXIOMTEK

AXIOMTEK GOT321W-521 Bedienungsanleitung

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Bedienungsanleitung

Qomo

Qomo QIT1386 Bedienungsanleitung

DFI

DFI KS104-CD Bedienungsanleitung

AMX

AMX AXP-PPC Leitfaden

Sartorius

Sartorius X3 PR 5410 Bedienungsanleitung

AMX

AMX Modero X Series Bedienungsanleitung

Advantech

Advantech TPC-30 Series Bedienungsanleitung

B&R Industries

B&R Industries MAPPC900-ENG Bedienungsanleitung