Risco WatchOUT XTreme 315DT Bedienungsanleitung

Dual Technology Outdoor Detector

Rivelatore da Esterno a Doppia Tecnologia

Detector de Exterior de Doble Tecnología

Détecteur extérieur à double technologie

Detector Externo de Dupla Tecnologia

Dual Technology-Buitendetector

WatchOUT 315DT

Installation Instructions - Relay & BUS Modes

Istruzioni per l’installazione in modalità Relé e BUS

Instrucciones de Instalación - Modos Relé y BUS

Guide d'installation - Modes Relais et BUS

Instruções de Instalação - Modos Relé & BUS

Relais- & BUS-modusinstallatie-instructies

2 WatchOUT 315DT Installation Manual

WatchOUT 315DT Installation Manual 3

Table of Contents

Relay Mode Installation..........................................................................................................4

Introduction ............................................................................................................................4

Mounting.................................................................................................................................4

Mounting Considerations......................................................................................................4

Wall Mount Installation.........................................................................................................5

Flat Mounting: ......................................................................................................................5

45° angle Mounting (Left side mounting) ..............................................................................5

Changing Back Tamper position ..........................................................................................6

Terminal Wiring .....................................................................................................................6

DIP Switch Settings .................................................................................................................7

Microwave Adjustment...........................................................................................................7

Walk test..............................................................................................................................7

LEDs Display ...........................................................................................................................7

Relay Mode / BUS Mode Jumper ..........................................................................................8

Standard Swivel Installation..................................................................................................8

Wall Mounting ......................................................................................................................8

Swivel Conduit Mounting......................................................................................................8

Replacing a Lens...................................................................................................................10

Lenses Types.....................................................................................................................11

Technical Specification.........................................................................................................12

Ordering Information...........................................................................................................12

UL Compliance Section ........................................................................................................12

BUS Mode Installation..........................................................................................................13

Introduction ..........................................................................................................................13

Terminal Wiring ...................................................................................................................13

DIP Switch Settings ...............................................................................................................13

ProSYS Programming ...........................................................................................................14

New System Parameters ......................................................................................................16

4 WatchOUT 315DT Installation Manual

Relay Mode Installation

Introduction

RISCO Group's Dual Technology Outdoor Detector, WatchOUT 315DT, is a unique detector with

signal processing based on two Passive Infrared (PIR) channels and two Microwave (MW)

channels. The detector can operate as a regular relay detector connected to any control panel, or

as a BUS accessory when connected to RISCO Group's ProSYS control panel via the RS485

BUS, thus having unique remote control and diagnostic capabilities.

The instructions describe herein, describe the WatchOUT 315DT in Relay & BUS mode.

Mounting

Mounting Considerations

1m - 2.7m

(3'3" - 8'9")

Optional Height: 1m - 2.7m

(3'3"-8'9")

Typical Height: 2.2m (7'2")

Default Lens: Wide angle 15m (50') 90°

(RL300)

Note:

1. For low installations, below 1.7m (5'6") in which

pet immunity is required, use the supplied

RL300F lens (low wall or fence installations).

2. The detector's pet immunity (height of an animal,

no weight limitation), is up to 70 cm (2'4"), when

installing the detector at 2.2m (7'2"). If the

installation is bellow the height mentioned

above, the Pet Immunity decreases accordingly;

every 10 cm (4") decrease in installation height

leads to 10 cm (4") decrease in pet imunity.

If possible, avoid pointing the detector to

moving objects (swaying trees, bushes etc.)

Out of

Detection Range

Keep distance of

minimum 5m (16')

from moving objects

5m (16')

Ensure any objects do not obstruct the field of

view for both technologies. Pay attention to

growing trees or bushes, plants with big

moving leaves etc

For installations with extensive vehicle traffic or targets beyond

the required detection range, it is recommended to adjust the

MW sensitivity and/or to tilt the detector down.

Note:

Tilting the detector down may reduce the pet immunity

For optimum detection, select a

location that is likely to

intercept an intruder moving

across the coverage pattern at

a 45° trajectory.

NOTE: Disable Proximity AM during heavy rain (if WatchOUT 315DT is not sheltered) to

prevent Proximity AM alerts.

WatchOUT 315DT Installation Manual 5

Wall Mount Installation

Note:

The installation knockouts numbering are marked on

the back plate.

1. Open WatchOUT front cover

(unlock C1, Figure 1).

2. Release internal base (unlock I1, Figure 2).

3. Select mounting installation as follows:

Flat Mounting:

Open knockouts on external base (Figure 3).

•B1 - B4: Wall mounting knockouts

•T1: Back tamper knockout

•W2 / W3: wires entry knockouts

45° angle Mounting (Left side

mounting)

a. Open knockouts on external base

(Figure 3)

•L1, L2: Left mounting knockouts

•T3: Left tamper knockout

•W5 / W6: Wire entry knockouts

b. Remove tamper spring.

c. Replace tamper bracket (Item 1) with

supplied flat tamper bracket (Item 2).

Item 1

Item 2

d. Insert Tamper lever B onto T5 and T3

and secure screw A (Figure 3).

4. Insert external wires through external base

W2, W3 (Flat Mounting) or W5, W6 (Left

side mounting) (Figure 3).

5. Secure external base to the wall.

6. Insert external wires and tamper wires

through internal base (Figure4).

7. Secure internal base to external base (lock

I1, Figure2).

8. Close the front cover (Lock C1, Figure1)

after wiring and setting DIP switches.

9. Walk test the detector.

Figure 1

Figure 2

Figure 3

Tamper

Lever

(not visible)

Figure 4

Note:

For 45° right side installation use the equivalent units on the external base as follows:

Knockouts Description Lef

Righ

Mounting Knockouts L1, L2 R1, R2

Tamper spring knockouts T1,T3 T2,T4

Tamper screw anchor T5 T6

Wiring Knockouts W5, W6 W7, W8

6 WatchOUT 315DT Installation Manual

Changing Back Tamper position

The back tamper is by default secured on the right

side of the internal base (rear view). If you wish to

move it to the left side (rear view), do the following

(Figure 5):

1. Remove tamper screw 1 in order to release the

tamper from position 7.

2. Ensure tamper spring 2 rests over tamper wire

base 4.

3. Ensure plastic tamper bracket 3 rests over both

2 and 4.

4. Secure tamper screw 1 into 3 over position 6.

Figure 5

Left Side

Tamper

Right Side

Tamper

Notes:

1. Verify that you hear a "Click" when attaching the tamper spring to the wall.

2. For pole installation, the tamper can be moved to the bottom right-hand side of the internal base.

Terminal Wiring

SET/

UNSET

LEDs

ENABL

YEL

FR E E

ALARM TAMPER

GREEN

FREE DUST TEST

12VDC

N.C N.C WatchOUT DT - PCB

+,- 12 VDC

ALARM N.C relay, 24VDC , 0.1A

FREE YEL This terminal is a free pin that can be used to connect wires and EOL resistors

TAMPER N.C switch, 24VDC , 0.1A

FREE

GREEN This terminal is a free pin that can be used to connect wires and EOL resistors

AM Normally closed AM relay output (24VDC, 0.1A) indicates Anti Masking alarm or any

trouble in the detector (not including dust/dirty lens).

The Proximity AM enables receiving sabotage alerts before the detector is

damaged or masked, using both microwave channels.

Note:

When DIP8 is defined as Enabled this relay also opens momentarily when a Proximity AM

attempt occurs.

LED

ENABLE Used to remotely control the LEDs when DIP1 is set to ON.

Enable: input is +12V OR no terminal connection

Disable: Connect the input to 0V

DUST N.O. collector max 70 mA. Indicates that the lens is dirty and requires cleaning.

TEST Used to perform remote alarm testing to the detector by applying 0 volts to this

terminal.

Success: Alarm relay is momentary opened.

Failure: AM relay is opened

SET

UNSET This input enables to control Anti-masking and LEDs operation in accordance to

the system status, Set (Arm) / Unset (Disarm).

While the system is armed this feature prevents an intruder from gaining

knowledge of the detector’s status and disables Anti-masking detection.

System Status Input Status AM Relay LEDs

Set (Arm) 0VOf

Unset (Disarm) 12V or no connection On* On**

* DIP7 is ON (Anti masking enabled)

** DIP1 is ON (LEDs enabled) and LEDs ENABLE input terminal is enabled

(+12V OR no terminal connection).

WatchOUT 315DT Installation Manual 7

DIP Switch Settings

5678

1234

Factory Defaults

DIP 4: Anti masking Sensitivity

On: High

Off: Low

DIP 5: Detector's optics

On: Barrier / Long range

Off: Wide angle

DIP 6: Red LED /3 LED

On: Red LED only

Off: 3 LEDs

DIP 7: Anti masking operation

On: Enabled

Off: Disabled

DIP 8: Proximity AM

On: Enabled

Off: Disabled

DIP 1: LEDs operation

On: LEDs Enabled

Off: LEDs Disabled

DIP 2-3: Detection Sensitivity

Sensitivity DIP2 DIP3

Low Off Off

Mid Off On

Normal (Defaul

) On Off

Maximum* On On

* In maximum sensitivity sway recognition is

disabled to achieve maximum sensitivity

Microwave Adjustment

Adjust Microwave coverage area by using the trimmer on the PCB.

MIN MAX

Walk test

Two minutes after applying power, walk test the protected area to verify

proper operation.

For installations on uneven surfaces slide the PCB inside the internal base to

the appropriate setting according to the desired height (1.0m, 1.5m, 2.2m,

2.7m) as printed on the bottom left corner of the PCB or use the standard

swivel accessory.

For reducing the detection range, slide the PCB up or tilt the swivel

down.

1.00M

1.50M

2.20M

2.70M

PCB

LEDs Display

LED State Description

YELLOW Steady Indicates PIR detection

Flashing Indicates Active IR AM (Anti mask) detection

GREEN Steady Indicates MW detection

Flashing Indicates Proximity AM detection

RED Steady Indicates ALARM

Flashing Indicates malfunctioned communication with ProSYS (BUS

mode only)

All LEDs Flashing (One

after another)

Unit initialization on power up

Notes:

1. DIP-Switch 1 should be in ON position to enable LED indications.

2. Only one LED is active at any one time. For example, in the case of both PIR and MW detection, either the

steady YELLOW LED or the steady GREEN LED is displayed (the first to detect), followed by the Alarm RED

3. In order to prevent the analysis of detection technologies such as PIR, Microwave, Active IR AM and

Proximity AM, set DIP Switch 6 (SW1) to ON. Only the red LED will be activated.

8 WatchOUT 315DT Installation Manual

Relay Mode / BUS Mode Jumper

J-BUS jumper (located on the PCB between the red and green

LEDs) is used to define the detector’s mode of operation as

follows:

Relay

Mode

BUS Mode

Standard Swivel Installation

The Outdoor detector packaging contains a standard swivel for flexible installation. Please follow

the instructions below for mounting the detector with the Standard Swivel:

1. Open WatchOUT front cover (Unlock C1, Figure1).

2. Release internal base (Unlock I1, Figure 2).

3. Open knockouts on external base (Figure 6, Detail B)

•W1: Wires knockout

•S1,S2: Knockouts for securing external base to Standard Swivel

•S3: External base locking screw knockout

4. On the swivel accessory remove the required swivel cable wiring knockout S2, S7 or S9

(Figure 6, Detail A).

5. Remove back tamper from the internal base (see “Changing Back Tamper Position"

paragraph) and connect it to S5 (Figure 6, Detail A) on the Standard Swivel.

Note:

Ensure that you see the engraved UP mark on the upper front face of the swivel.

6. Select the mounting installation type as follows:

Wall Mounting

a. Insert external cable wiring through knockouts S2, S7 or S9 and extract them (including the

tamper wires) through the Swivel Wires Passage (Figure 6, Detail B).

b. Secure swivel to the wall through holes S1, S3, S6 and S8.

Swivel Conduit Mounting (using Conduit Metal Swivel Adaptor – CSMA, Figure 6, Detail A)

S1 S2 S3

S7 S6

Tamper

(see Detail C)

Swivel Wires

Passage

Tamper

Spring

Holes

Ø 21 mm

Ø16 mm

CSMA

Detail ADetail B

Snaps

Standard Swivel

Detail C

Figure 6

Note:

The CSMA is required when wall external wiring is used and protection pipe is required. The CSMA should

be ordered separately - P/N RA300SC0000A.

a. Choose the direction upon which to mount the CSMA according to the required diameter:

16mm (0.63 inches) or 21mm (0.83 inches).

b. Insert conduit to the CSMA.

WatchOUT 315DT Installation Manual 9

c. Secure CSMA to the wall through points (M1, M4).

d. Insert external cables and tamper wires from the conduit through the swivel wires

passage of the swivel (Figure 6, Detail A).

e. Secure swivel to the wall through holes S1, S3, S6 and S8.

Note:

The Tamper spring S5 (Figure 7) should make contact with the wall through the tamper spring holes M2 or

M3 on the CSMA. Make sure to hear the tamper "Click" when connecting to the wall.

7. Insert tamper wires and external cable wiring from Standard Swivel through knockout W1 on

the external base (Figure 6, Detail B).

8. Connect the external base to the swivel using the dedicated snaps (Figure 7).

PCB

External Base

Internal Base

Angle Locking

Screw

(See Note 2)

See Detail A

Swivel to External Base

Connecting Screws

Detail A

Swivel Assy

Connecting Screw

(See Note)

Snaps

Figure 7

Note:

Do not open or close the Swivel Assy Screw since it is used for connecting the swivel parts only.

9. Secure external base to swivel with two screws fastened to knockouts S1 and S2 (Figure 7).

10.Insert the supplied angle locking screw from the external base through the angle locking screw

knockout S3 on the external base to the standard swivel (Figure 7).

11.Tilt and Rotate the Standard Swivel to the desired position. Once the Standard Swivel is in the

desired position, secure the angle locking screw.

12.Line up the internal base onto the external base. Insert all wiring cables through the internal

base.

13.Secure internal base to external base (Lock I1, Figure 2).

14.To readjust the Standard Swivel when the PCB is installed (Figure 7):

a. Bend down the black foam located below the RED LED on the PCB (enough to reach the

Swivel locking screw).

b. Use a Philips screwdriver to release the locking screw (see Figure 8).

c. Tilt and/or Rotate the Standard Swivel to the desired position.

d. Secure the angle locking screw.

Note:

When marks on the two movable parts are aligned (Figure 8), the Standard Swivel is in 0°

vertical /horizontal position. Each click from this position represents shifting of 5°in vertical / horizontal

position.

15.Close the front cover (Lock C1, Figure 1) and walk test the detector.

10 WatchOUT 315DT Installation Manual

Note:

The screw has to pass through External Base and locked to the swivel.

Figure 8

Replacing Lenses

1. Unlock the six screws that hold the lens holding sleeve from the back of the front cover.

2. To release the protective sleeve, gently push the lens from the external side of the front cover.

3. Disconnect the lens from the sleeve by gently pushing the lens clips that secure it to the

sleeve.

4. Replace the lens. Place the 4 clips of the lens into the matching holes on the sleeve.

5. Insert the protective sleeve back into place on the front cover. Pay attention to place the

sleeve over the sealing rubber.

6. Secure the 6 holding screws back to their place.

Lens Protecting

Sleeve

Sockets for

Lens Clips

Sleeve Locking

Screws

Lens Locking

Clips

Sealing Rubber

Front Cover

Locking Screw

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Risco Sicherheitssensor Handbücher

Risco

Risco Industrial LuNAR RK200DTG3 Bedienungsanleitung

Risco

Risco Beyond Wireless DT Bedienungsanleitung

Risco

Risco Digital ZoDIAC RK410PRD Bedienungsanleitung

Risco

Risco RK350DT Bedienungsanleitung

Risco

Risco RWX106BA Bedienungsanleitung

Risco

Risco eyeWAVE RWX95CMP Bedienungsanleitung

Risco

Risco Wireless VITRON RWT6G Bedienungsanleitung

Risco

Risco RWT6F Bedienungsanleitung

Risco

Risco EL-5835D Bedienungsanleitung

Risco

Risco ShockTec 600S Bedienungsanleitung

Risco

Risco iWAVE T95 Bedienungsanleitung

Risco

Risco Wirless WatchOUT RWX312PR800C Bedienungsanleitung

Risco

Risco Bware RWX515PR Bedienungsanleitung

Risco

Risco Wireless WatchOUT PIR 868 Bedienungsanleitung

Risco

Risco WL X312 Bedienungsanleitung

Risco

Risco iWISE Wireless RWT92 Bedienungsanleitung

Risco

Risco DigiSense Digi-412DTPT Bedienungsanleitung

Risco

Risco iWave RWX95 Bedienungsanleitung

Risco

Risco iREX Bedienungsanleitung

Risco

Risco WatchIN RK325DT Bedienungsanleitung

Risco

Risco Digi-415DT Bedienungsanleitung

Risco

Risco BWare BUS DT AM G3 Bedienungsanleitung

Risco

Risco RK66S Bedienungsanleitung

Risco

Risco iWISE QUAD AM Grade 3 Bedienungsanleitung

Beliebte Sicherheitssensor Handbücher anderer Marken

THORLABS

THORLABS PDA10JT Bedienungsanleitung

Waeco

Waeco UV-DETECT Bedienungsanleitung

Intermatic

Intermatic IOS-DSIMF Bedienungsanleitung

urmet domus

urmet domus 1083 Bedienungsanleitung

Siemens

Siemens AZL66 Series Bedienungsanleitung

BTI

BTI Profiline Multi Finder Bedienungsanleitung

Challenger

Challenger SL01 Bedienungsanleitung

DMP Electronics

DMP Electronics 1122INT Bedienungsanleitung

Rielta

Rielta Ladoga MK-RK Bedienungsanleitung

Mirion Technologies

Mirion Technologies ACCURAD PRD Bedienungsanleitung

Bosch

Bosch DS835 Bedienungsanleitung

DBI SALA

DBI SALA EZ Stop Bedienerhandbuch

Lamptime

Lamptime ST05C Bedienungsanleitung

Ubiquiti

Ubiquiti MFI-MSC Bedienungsanleitung

Subsite

Subsite 910R Montageanleitung

Satel

Satel OPAL Pro Bedienungsanleitung

Aleph

Aleph XC-1XTEU Bedienungsanleitung

Pima

Pima LARIS QUAD Bedienungsanleitung