Riva RC6702SV-7311 Bedienungsanleitung

NC6702SV(73H_73V722H)02-2017-A

Quick Installation Guide

This manual provides instructions for the quick installation and basic configuration of your IP device.

1. Part names and positions

Please check the name and position of each part by referring to the following images.

Make sure the polarity is correct. Incorrect connection may

cause malfunction or damage the IP device.

Caution

Power Adaptor Connector (DC 12V)

SD Card

Video Out

PAL/NTSC

Reset

* Model design and appearance are subject to change without any prior notice.

LAN Connector

Power Adaptor Connector

BLACK: AUD IN

BROWN: AUD GND

RED: AUD OUT

ORANGE : DI

YELLOW: DI COM

GREEN: DO1 (N.O)

BLUE: DO1 COM

Terminal Connector

NC6702SV(73H_73V722H)02-2017-A

2. Installation

There is only one type of mounting explained in this manual. Refer to the camera’s installation guide for the

various mounting types.

Note

< Installation of Ferrite Core >

Installing the ferrite core is highly recommended to reduce high frequency noise level.

The instructions and the image below explain how to install the ferrite core on the cable.

1. Open the ferrite core by lifting the clip.

2. Make one loop with the cable through the ferrite core like in the enlarged image below.

3. Close the ferrite core to hold the cable loop into place.

Caution

Sealing gaps is recommended as gaps may appear after the camera installation.

Gaps may cause problems such as moisture, water leakage and etc., which negatively affect

the operation of the camera if gaps remain unsealed.

1) Place the installation template included in the

package on the desired installation surface.

2) Drill three holes in the correct positions based on the

template paper, and insert the plastic anchors into

the holes.

3) Attach the silicon waterproof band included in the

package to the camera’s mounting surface by

aligning it with the three alignment holes.

4) If your package includes a ferrite core, install it on

the cable. Refer to the note below for the detailed

instructions.

5) Connect the required cables including a power cable

and a LAN cable to the device. Refer to 1. Part names

and positions and 5. CONNECTIONS in the product

installation guide for more information.

6) Place the camera body on the installation surface by

matching three alignment holes with the already

inserted plastic anchors.

7) Tighten the plastic anchors with the screws (M4x30)

included in the package.

8) Adjust the heading direction of the camera. Please

refer to 3. Adjust angle of the camera for more

information.

9) To adjust zoom and focus, refer to 4. Adjust Zoom

and Focus for the instructions.

NC6702SV(73H_73V722H)02-2017-A

Caution

To prevent products from damage, place the camera on a stable and non-vibrating surface.

If the stability is in doubt, consult safety personnel for reinforcements, and then proceed

with the installation.

3. Adjust angle of the camera

1) Adjust the camera to the desired angle by unscrewing the joints with the provided hex wrench (3mm) by

referring to the following pictures.

2) Connect to the web page of the device to see its real-time image in order to check whether its angle is

properly adjusted. Refer to 6. View video on web page for more information about using its web page.

*To quickly check if the angle is correct, the camera can be connected to an analogue video test monitor

using the video output cable (included in the package) and the NTSC/PAL button.

4. Adjust Zoom and Focus

* To adjust zoom and focus, you need to connect the device to the network.

Please refer to 5. Set up network environment and 6. View video on web page for the instructions on how

to connect the device to the network.

Once you are on the webpage, go to Setup> Video & Audio > Zoom/Focus. Then, you will see the features

like below.

1) Adjust zoom and focus by clicking the arrow buttons: the buttons move the lens more extensively

than the buttons .

2) Click One Click Focus to automatically set the lens.

3) In case the focus point is considered misaligned, reset it to a zero point by clicking Calibrate.

Adjust the joint to install

the camera on the wall.

Adjust the joint to tilt

the camera angle.

Adjust the joint to delicately

adjust the horizontal angle.

NC6702SV(73H_73V722H)02-2017-A

5. Set up network environment

The default IP address of the device is 192.168.XXX.XXX. Users can identify the IP address of the device from

converting the MAC address’s hexadecimal numbers, which is attached to the device. Be sure that the device

and PC are on a same area network before running the installation. If the network segment was different

between your PC and the device, change your PC’s settings as below.

IP address : 192.168.xxx.xxx

Subnet mask: 255.255.0.0

Generic IP Environment

In case of generic private network environment where IP address 192.168.XXX.XXX are used, users may view

the live streaming images on a web page using the device’s default IP address:

1) Convert the device’s MAC address to the IP address. Refer to the Hexadecimal-Decimal Conversion Chart at

the end of the manual.

(The MAC address of the device is attached on the side or bottom of the device.)

2) Start the Microsoft® Internet Explorer web browser, and enter the IP address of the device.

3) Authorize and install the ActiveX setup.exe when the ActiveX installation pop-up window appears. Web

streaming and device configurations are supported through ActiveX program.

MAC address = 00-13-23-01-14-B1 → IP address = 192.168.20.177

Convert the last two sets of hexadecimal numbers to decimal numbers.

NC6702SV(73H_73V722H)02-2017-A

IPAdminTool

Please access our website and download necessary IPAdminTool first:

http://www.rivatech.de/en/downloads/software

IPAdminTool is a management tool, which automatically scans all of the network products for users to perform

administrative tasks, which includes network configurations, firmware update, device reboot, and more.

To modify the device’s default IP address for customized network area:

1) Find the device from the IPAdminTool’s list, and highlight the device’s name.

2) Right-click the mouse, and select IP Address; IP Setup window appears.

* There are two options that are for a single device or for multiple devices respectively. For one device, click “Single”.

3) On the New Information table in the Single IP Change window, modify the last two digits of the device’s IP

address. Make sure to input the correct ID and PW of the device (default: root / pass).

4) Click Apply to complete the modification.

Give a new unique IP address by

modifying the last two digits.

NC6702SV(73H_73V722H)02-2017-A

6. View video on web page

Once the device’s proper IP address has been identified, type the URL in a web browser to access the camera.

At first time access, installation window may pop up.

1) When the browser asks to install the AxUMF software, click Install to proceed.

2) When Setup installation pop-up window appears, click Install to proceed with rest of installations.

Note

Depending on system OS and Internet Explorer version, installation experience may differ

from one another. Figures described above are from Windows 7, Internet Explorer 9

environment.

7. SETUP page

To set up the device configuration:

1) Click Setup on the upper left of the web page. The login page is displayed as below.

2) Enter the user name and the password, and then select OK.

(The default username and password are: root and pass.)

8. Reboot

Perform the following procedures to reboot your device:

On the Device

1) Press the reset button for 2 seconds while the device is powered on.

2) Wait for the system to reboot.

Caution

Please do not press the reset button for more than 2 seconds. Otherwise, the camera may be

switched to its factory default settings.

NC6702SV(73H_73V722H)02-2017-A

On the Camera’s Webpage

1) Go to Setup > Maintenance > Reboot.

2) Click Reboot to reboot the device.

9. Factory Default

Resetting the device back to the factory default will initialize all parameters including the IP address back to

the factory defaults. To reset back to the factory default:

On the Device

1) Press the reset button, and hold it while the device is powered on.

2) Release the button after 10 seconds.

3) Wait for the system to reboot.

On the Camera’s Webpage

1) Go to Setup > Maintenance > Reset All Settings.

2) Select the items that you want to keep from the initialization among network settings, user account

information, and time zone setting.

3) Click Reset All Settings.

Note

The factory default settings can be inferred as follows:

IP address: 192.168.xx.yy

Network mask: 255.255.0.0

Gateway: 192.168.0.1

User ID: root

Password: pass

10. Safe Mode

Your device will get restarted in safe mode if the device does not completely boot certain times.

The errors are mainly caused by these factors below:

* The power supply is continually unplugged certain times in the middle of system booting.

* The firmware files required for system booting are damaged.

* There are conflicts in the system settings.

You will see the page to indicate that your device is in safe mode and to guide you what to do step by step.

Follow the instructions on the webpage according to each step.

Note

There is another method to update firmware, which is using IPAdminTool.

Please refer to ‘IPAdminTool User’s Manual.pdf’for the detailed procedure.

Note

If your device is still in safe mode after trying to update firmware, please contact your local

agency to get further assistance.

NC6702SV(73H_73V722H)02-2017-A

Hexadecimal-Decimal Conversion Table

Refer to the following table when you convert the MAC address of your device to IP address.

Hex

Dec

Hex

Dec

Hex

Dec

Hex

Dec

Hex

Dec

Hex

Dec

Hex

Dec

111

148

185

222

112

149

186

223

113

150

187

224

114

151

188

225

115

152

189

226

116

153

190

227

117

154

191

228

118

155

192

229

119

156

193

230

120

157

194

231

121

158

195

232

122

159

196

233

123

160

197

234

124

161

198

235

125

162

199

236

126

163

200

237

127

164

201

238

128

165

202

239

129

166

203

240

130

167

204

241

131

168

205

242

132

169

206

243

133

170

207

244

134

171

208

245

135

172

209

246

136

173

210

247

100

137

174

211

248

101

138

175

212

249

102

139

176

213

250

103

140

177

214

251

104

141

178

215

252

105

142

179

216

253

106

143

180

217

254

107

144

181

218

255

108

145

182

219

109

146

183

220

110

147

184

221

Andere Handbücher für RC6702SV-7311

Inhaltsverzeichnis

Andere Riva Sicherheitskamera Handbücher

Riva

Riva RC4100-IN Bedienungsanleitung

Riva

Riva RC3502HD-5311IR Bedienungsanleitung

Riva

Riva RC5510 Bedienungsanleitung

Riva

Riva RC3500M Bedienungsanleitung

Riva

Riva RC3500 Bedienungsanleitung

Riva

Riva RC5510 Bedienungsanleitung

Riva

Riva RC3502HD-5311 Bedienungsanleitung

Riva

Riva RC4100-1212-27 Bedienungsanleitung

Riva

Riva RC6702SV-7311 Bedienungsanleitung

Riva

Riva RC6802HD-6217 Bedienungsanleitung

Riva

Riva RC3402HD-6211IR Bedienungsanleitung

Riva

Riva RC3502HD-5311 Bedienungsanleitung

Riva

Riva RC3500 Bedienungsanleitung

Riva

Riva RC8102HD-6111T Bedienungsanleitung

Riva

Riva RC3302HD-5344 Bedienungsanleitung

Riva

Riva RC6602HD-5311 Bedienungsanleitung

Riva

Riva RC3202HD-6111 Bedienungsanleitung

Riva

Riva RC3202HD-6111W Bedienungsanleitung

Riva

Riva RC302HD-5117 Bedienungsanleitung

Riva

Riva RC3702HD-5314 Bedienungsanleitung

Riva

Riva RC362HD-6211IR Bedienungsanleitung

Riva

Riva RC100 Bedienungsanleitung

Riva

Riva RC4602SV-7416A-30 Bedienungsanleitung

Riva

Riva IPX5502HD-6415-05 Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung