Riverlea CEDAR SHED COVENTRY Bedienungsanleitung

CEDARSHED INSTRUCTIONS

COVENTRY - COLOURSTEEL ROOF

Base size: 2700mm x 1500mm deep

COVENTRY

• Baery Drill

• Riveter

• Hammer

• Tape Measure

• Ladder

• Skillsaw

• Level

• Screwdriver - Flat

• 3/8 Hex Drive bit

• 8mm Hex Drive bit

• Drill Bit 3.2mm

• Read all instrucons carefully.

• Idenfy all parts and check quanes against checklist.

• Do not aempt to build your shed in high winds.

• Beware of sharp edges.

• Protect your eyes and ears.

• Use electric tools with care. Use a Safety Trip Switch.

• It is easier and quicker if this shed is erected by two people.

• Your shed must be level. Achieve this by either levelling the

ground or by using blocks.

Tools Required:

Select your site:

Safety:

Before you start:

COVENTRY PARTS LIST

Descripon Size Qty

PACK ONE - SHED

Standard Door 895 x 1780 1

Front Wall Panel 900 x 2177 2

Back Wall Panels 900 x 1937 3

Side Raking Wall Panels (1L, 1R) 1410 x 2152 2

Cedar Corner Clashings - Front 65 x 17 x 2152 2

Cedar Corner Clashings - Back 65 x 17 x 1962 2

15 x 17 Std Cedarbead 15 x 17 x 1937 2

30 x 17 Long Cedarbead 30 x 17 x 1937 2?

15 x 17 Long Cedarbead 15 x 17 x 2180 4

Bargeboards 90 x 17 x 1850 2

Door Stop 45 x 45 x 900 1

Door Lintel 405 x 900 1

Silicone Tube 300g 1

Weatherstrip 50mm x 20m Roll 1

Seners 45 x 45 x 2700 2

Building Paper 1370 x 3700 1

Roong Sheets 875 x 1820 3

Roong Sheet—2 pan 390 x 1820 1

Purlins 70 x 45 x 2885 2

Spoung 2880mm 2

15mm Packer 15 x 45 x 1720 1

Hardware Pack

Tek Screws 14G x 75mm, CL4 60

Framing Nails 75 x 3.15mm 50

Bead Nails 50 x 2.5mm 75

Clouts (Cladding nails) 30 x 2.5mm 70

Colour Rivets 3.2 x 9.6mm 50

Roong Screws 50mm 36

Door Handle 1

Door Latch 1

Door Handle Screws 3/16 x 2.5” 2

Instrucons 1

PACK TWO - FLOOR (if required)

Floor Boards 150 x 25 x 1490 18

Floor Joists 70 x 45 x 2690 4

Floor Nails 50 x 2.5mm 150

Packed by: Date: / /

PG 2

COVENTRY CONCRETE FLOOR - OPTIONAL

Step 1: Establish size of shed and excavate sucient area. Re-

member to allow for rear roof overhang up to 150mm, and

120mm on each end.

Step 2: Ensure that the base substrate is compacted rmly.

We suggest that the slab should be 80mm thick in the middle

and 100mm thick around the edges.

Step 3: Lay boxing to the required size, the raised slab

size should be 2685 x 1485mm and at least 30mm

above the ground line.

Step 4: Lay plasc sheeng if required. Plasc sheeng under slab

will prevent moisture coming through from underneath.

Step 5: Pour concrete and screed ush

Building a Raised Concrete Base

100mm

80mm

100mm

PG 3

COVENTRY FLOOR - OPTIONAL

PG 4

Step 1: Lay out oor joists, spacing them evenly

as shown. Using 50mm ooring nails, nail a oor

board on each end, ensuring ends are ush with

joists. Make sure oor is level and joists are sup-

ported at 900mm centres.

Step 2: Lay out remaining oor boards. Measure

diagonals to ensure measurements are equal (i.e.

oor is square). Rip down last oor board to suit

gap, and nail o oor with 50mm ooring nails (8

nails per board).

Step 3: Nail plasc weather strip to edge of oor on

all four sides, with 30mm clouts, (approx 3-4 nails

per side) ensuring top edge is ush with top of oor.

This isn't required if shed is on a concrete base.

Step 4: Unpack panels and idenfy wall panels

and door posions as per plan on following page.

Select two panels that go either side of a corner

(i.e. end and standard panel) and stand together.

COVENTRY WALL PLAN

15 x 17mm Std Cedar bead

30 x 17mm Std Cedar bead

Corner Clashing

45 x 15mm Packer

Tek Screws (To secure walls to the oor)

Please note: The walls are not screwed down to the oor unl all the walls

are erected, the roof is in place and the doors are about to be installed.

PG 5

COVENTRY WALL PLAN

1410R 1410L

900

900 900 900

NOTE: FRONT WALL IS THE HIGH WALL.

COVENTRY WALLS

PG 6

Step 5: Screw wall panels together using 75mm

Tek screws (3 per short panel, 4 per long panel),

ensuring side raking wall panels are inside the

front and back wall panels as per wall plan.

Step 6: Silicone edge of weatherboards on standing

panel and nail on cedar beads with 5 x bead nails.

(Refer to wall plan for correct beads).

Make sure bead is properly sealed to avoid leaks.

Note: On standard panels only, top of bead is bev-

elled to allow for slope of roof.

Step 7: Silicone and nail remaining beads on each

panel. Screw panels together using 3 Tek Screws

per join and 4 on the longer joins on gable end

panels.

Step 8 Silicone and nail 15mm bead each side of

door way.

COVENTRY TOP STIFFENER

COVENTRY TOP LINTEL

PG 7

Step 9: Using 4 x 75mm tek screws screw

door lintel to studs. Ensure outside cedar

weatherboard on lintel is ush with weather-

boards each side .

Door lintel shown from inside

Door lintel shown from outside.

Step 10: Using 75mm framing nails, nail both top

plate seners into front and back wall panels

studs, as shown using 2 nails per stud. Ensure

ends are ush before nailing.

Note Front sener is bevelled to suit roof angle.

Step 11: Using 30mm clouts nail top cedar boards

to Seners (2-3 per board). Predrill holes to stop

boards from spling.

COVENTRY CORNER CLASHINGS

COVENTRY ROOF

PG 8

Step 12: Silicone and nail 15 x 17mm beads on all cor-

ners as shown using 5 x 50mm beading nails, per

bead.

Step 13: Silicone and nail corner clashings on all cor-

ners as shown using 5 x bead nails per clashing. Note

long clashings at the front, short clashings at the rear.

Ensure clashings are ush with the top of side panel

as shown.

Silicone both edges of clashing to ensure this doesn't

leak.

Step 14: Posion both purlins on roof as shown.

Top purlin and boom purlins should be against

top plate seners. Using 75mm framing nails,

nail purlins to end panels (2 nails per join)

Step 15: Using 1 x 75mm tek screw , screw

boom purlin to top plate centrally in shed.

Repeat with top purlin.

Step 16: Ensure shed is square, by measuring diagonals at top corner of wall panels.

Using 30mm clouts, nail building paper on to purlins.

Note: Temporary screw packaging mber to underside of Purlins to hold purlins straight

unl roof is screwed o

Step 17: Posion rst full sheet with rib ush

with ends of purlins and 200mm overhang at

front of shed.

Using a 50mm Roong Screw with Washer,

screw through the rib into the front purlin.

Note. Predrilling with a 3mm drill bit may

make this easier.

Step 18: Lay out remaining full roof sheets.

Rivet these sheets together, 2 rivets per join,

to make 1 large roof panel as shown in photo.

Tack remaining front corner and back corner

ensuring edge of sheet is ush with end of

purlins and front overhang is correct.

Ensure purlins are straight and screw through

each rib into the front and back purlins.

COVENTRY ROOF

PG 9

Inhaltsverzeichnis

Andere Riverlea Außenlagerung Handbücher

Riverlea

Riverlea SmartStore SS2520 Bedienungsanleitung

Riverlea

Riverlea Duratuf Sentry Sheds SL1520 Bedienungsanleitung

Riverlea

Riverlea SmartStore SM2520 Bedienungsanleitung

Riverlea

Riverlea Duratuf Gurdian Sheds GS62 Bedienungsanleitung

Riverlea

Riverlea SmartStore SM2015 Bedienungsanleitung

Riverlea

Riverlea Smart Store SM2010 Bedienungsanleitung

Riverlea

Riverlea SmartStore SM3020 Bedienungsanleitung

Riverlea

Riverlea Duratuf Garrison Sheds PL46 Bedienungsanleitung

Riverlea

Riverlea Duratuf SENTRY SHEDS SG2020 Bedienungsanleitung

Riverlea

Riverlea Rustics NEBRASKA Bedienungsanleitung

Riverlea

Riverlea Duratuf Garrison Sheds PL36 Bedienungsanleitung

Riverlea

Riverlea SmartStore SM2007 Bedienungsanleitung

Riverlea

Riverlea Duratuf Garrison Sheds PL43 Bedienungsanleitung

Riverlea

Riverlea Duratuf Guardian SHED SGS73 Bedienungsanleitung

Riverlea

Riverlea Duratuf Garrison Sheds PS62 Bedienungsanleitung

Riverlea

Riverlea DURATUF Sentry SL2015 Bedienungsanleitung

Riverlea

Riverlea SmartStore SM1520 Bedienungsanleitung

Riverlea

Riverlea Duratuf Guardian SHED SG3025 Bedienungsanleitung

Riverlea

Riverlea Smartstore SS2020 Bedienungsanleitung

Riverlea

Riverlea Duratuf KIWI SHEDS MK4A Bedienungsanleitung

Riverlea

Riverlea SmartStore SM3025 Bedienungsanleitung

Riverlea

Riverlea SmartStore SM3015 Bedienungsanleitung

Riverlea

Riverlea Duratuf SS2010 Bedienungsanleitung

Riverlea

Riverlea SmartStore SM1515 Bedienungsanleitung

Beliebte Außenlagerung Handbücher anderer Marken

USP

USP DURAMAX 10 Ft x 8 Ft StoreMax Plus Bedienungsanleitung

TYGO

TYGO Nyland Bedienungsanleitung

Duratuf

Duratuf GL105 Bedienungsanleitung

Viking

Viking SD5300SS Technisches Handbuch

USP

USP DURAMAX Apex Pro 10.5 Ft x 8 Ft 40116 Bedienungsanleitung

ModuLaro

ModuLaro Lojo WC202200 Bedienungsanleitung

Lifetime

Lifetime 6418 Bedienungsanleitung

rollaway container

rollaway container ARPCA24 Bedienungsanleitung

Duratuf

Duratuf Havelock Bedienungsanleitung

X-METAL

X-METAL 4065 Bedienungsanleitung

Outdoor Life Products

Outdoor Life Products FP2030 F Bedienungsanleitung

Royalcraft

Royalcraft Faro 295L Storage Box Bedienungsanleitung

Rubbermaid

Rubbermaid 5L45 Bedienungsanleitung

garofalo

garofalo TUSCANY EVO Bedienungsanleitung

OLT

OLT GS84D-FJ-Plywood Bedienungsanleitung

Duratuf

Duratuf Kiwi MK1 Bedienungsanleitung

Eden

Eden CA2988 Bedienungsanleitung

Palram

Palram CANOPIA RUBICON 6x10 Administratorhandbuch