Riverlea Duratuf KIWI KS3 Bedienungsanleitung

Quality – Built In

ASSEMBLY INSTRUCTIONS

KS3

BASE SIZE 3380mm x 876mm

CHECK OUT OUR ASSEMBLY VIDEO

Let Keith and Justin show you how to build your

Kiwi shed like a professional.

When used in conjunction with these assembly instructions, Keith’s practical tips and tricks will

make your assembly experience that much simpler, giving you visual guidance through sections

that seem tricky on paper, and help you achieve a flawless end result.

To view the video visit www.duratuf.co.nz/kiwi-assembly

Note: Assembly video features a MK2. But can be used for reference for any other Kiwi model.

• Drill

• Drill Bit 3.5mm

• Drill Bit 6mm (for clear roof panel only)

• Hex Drive 5/16

• Riveter (free Duratuf riveter supplied in kit)

• Hammer

• Nail Punch

• Tape Measure

• Ladder or Saw stool

• Spanners x 2

• String Line

• Tin Snips

• Skillsaw and Jigsaw (for floor only)

• Masonry Drill and 10mm Masonry Bit (for Bolt Down Kit only)

• Read all instructions carefully.

• Identify all parts and check quantities against checklist.

• If you are making your own floor refer to Raised Base Plate section

now.

• Do not attempt to build your shed in high winds.

• Beware of sharp edges.

• Protect your eyes and ears.

• Use electric tools with care. Use a Safety Trip Switch.

• It is easier and quicker if this shed is erected by two people.

• Your shed must be level. Achieve this by either levelling the ground

or by using blocks.

• If you shed is to be positioned on wet or damp ground, we recom-

mend that your shed is raised up off the ground slightly.

Tools Required:

Select your site:

Safety:

Before you start:

ASSEMBLY INSTRUCTIONS

1.890m

1.016m

Wall Sheets

Door - Standard Security

Instruction Booklet

Hardware Pack

Touch-up Paint & Brush

0.580m

0.603 x 0.603m

0.588 x 0.150m

Fixed Window Frame

Glaze Beads

Glass

Louvre Window Frame

Glass

Window Hardware Pack

1.016m Clear Roof Panel

Security Single Door Hardware Pack

Alarm - MA20

Shed light

Bolt Down Kit

Peg Down Kit

Roof Sheets

1.016m Roof Sheet

100

50mm

75mm

Flooring Nails

Duratuf Riveter

KIWI KS3 PARTS LIST

KS3 TIMBER FRAME

45 45

786

876

45 45

END WALL

883

1900

1945

1.810

YELLOW

45 45

785

3380

45 45

FRONT WALL

883

45 795 451622

KS3 TIMBER FRAME

Step 2: Select one 3.380m Base Plate (Green), one

3.380m Ridge Beam (90 x 45). Stand up End

frame with the Stud side of the frame on the

ground. Nail 3.380m plates to frame using two

nails per join. Ensure Green joins to Green and

Red joins to Red. Repeat with other end frame.

Nail in back wall centre stud using 1.622m Nogs

to get correct position. Position Nogs .883m

down from Top Plate and nail in place.

Step 1: End Walls: Select 1 x 0.876m End Base Plate

(Green), 1 x 0.876m End Top Plate (Red) and 2 x

Studs (Yellow). Lay out Plates and two Studs on

a flat surface and nail together using two 75mm

nails per join. Position 0.786m Nog 0.883m down

from Top Plate and nail in place. Repeat with

other end wall.

Step 3: Select one 3.380m Base Plate (Green) and one

3.380m Top Plate (45 x 45). Nail in place. Ensure

Green joins to Green.

Step 4: Carefully roll the frame over so that the Ridge

Beam and Base Plate (Green) are on the top.

Select two studs (Yellow), one .785m Nog and

one 1.622m Nog. Nail in studs using Nogs to get

correct position ensuring the 0.785 Nog is to the

right of the door (see diagram 4) . Nail in Studs

using the .785m nogs to get the correct position

top and bottom. Position nogs .883m down from

the bottom of the Top Plate and nail in place.

Step 5: Carefully roll frame over onto its base. If fitting a

Kiwi Floor, fit Floor Joist now. Place the joist cen-

trally and nail in place using three 75mm nails

per end.

Note: For sheds with the Raised Floor Modification option the studs will be 1.780m long to allow the Wall Sheets to pro-

trude 20mm below the Bottom Plate. Refer to Raised Floor Modification section (Page 15).

Note: If fitting a window in the Back Wall, there will be no centre stud on that side. Instead nail in a full length Nog (3.290) using

Window Studs (.883) to get correct height. Position one Window Stud centrally beneath the Nog and nail in place. Further

window studs and Nogs are fitted after the cladding is on.

KS3 WALL CLADDING

TO AVIOD CORROSION:

• Where at all possible try not to trap metal filings between two sheets. Remove all metal filings before riveting.

• Carbon in pencils reacts with the Zinc/Aluminium coating on steel. Use either crayon or ink to mark steel.

TERMS EXPLANATION

• To Tack: To Tack on a wall sheet means to use minimum nails hammered partly in to hold Wall Sheets in position. Should a Wall

Sheet need to be re-positioned, the nails can easily be prized out.

• If a window is required, identify Wall Sheet(s) with window hole pre-cut. Lean up Wall Sheets where window(s) are to be located.

fig. 1

CLADDING DETAIL

Birds Eye View

KS3 WALL CLADDING

Step 2: Back Wall: Position the first Wall Sheet with

the LIP on the right hand side. Ensuring the LIP

is flush with the side of the corner Stud and the

top of the Wall Sheet is 45mm down from the

top plate, tack in place. Position the next Wall

Sheet with the LIP on the right hand side. Over-

lap as shown in fig 1 pg 6. Ensuring Wall Sheet

is 45mm down form the top plate, tack in place.

Repeat with remaining Wall Sheets.

Step 4: Nailing Off: Nail one 30mm Clout each side of the Rib (two per Pan) into the Top Plates and Bottom Plates. Nail

Wall Sheets to mid wall Nogs (one per pan). Nail each corner Wall Sheet to Studs using two 30mm Clouts evenly

spaced.

Step 3: End Walls: Position wall sheet with the LIP

flush with the side of the stud and the top of

the Wall Sheet is flush with the top of the Top

Plate, tack in place. If fitting a window, nail in

Window Studs and Nog now. Refer to Window

instructions.

Step 1: Front Wall: Start at the left hand side. Position the

Wall Sheet with the LIP on the left hand side. Ensur-

ing the LIP is flush with side of the Stud and the top of

the Top Plate, tack in place. Repeat with Wall Sheet

on the right hand side of doorway.

EDGE

TOP

KS3 WINDOW (Optional)

Step 2: On the inside of the shed, position studs

and Nog centrally on window opening.

Make sure the studs are parallel and nail

into Top Plate and End Wall Nog.

Step 3: Nail wall Sheets to window framing using

30mm clouts. (return to step 4 on page 7

and complete). Then fit Window Frame).

Position Window Frame centrally on win-

dow opening and rivet it to ribs. Pre-drill

holes in each corner and nail Window

Frame to framing, using 50mm nails.

588mm

Step 1: Lay out the two window studs (883mm) and

Nog (634mm) on a flat surface. Position

Nog and nail in place using 2x 75mm nails

at each end.

Step 6: From the inside of the shed, slide Louvre

Glass into Louvre Units attached to the

Window Frame. Bend up tabs to keep

Glass in position.

570mm

Step 6: From the outside of the shed, place glass

in Window Frame. Attach a Glazing Bead

(G100) with three rivets to each side of the

Window Frame to hold glass in place. Pre-

drilling Glazing Beads is recommended.

Step 1: Lay out the two window studs (883mm) and

Nog (590mm) on a flat surface. Position

Nog and nail in place using two 75mm nails

at each end.

FIXED WINDOW

LOUVRE WINDOW

50mm

NAILS

RIVITS

KS3 DOOR JAMB & CORNER FLASHINGS

Step1: Fit Door Jamb Flashing (104) in between

Top and Bottom Plates and hard against

Stud. Attach Door Jamb Flashing with

three rivets into Rib on the outside and

three 30mm clouts into studs on the in-

side. Repeat with the other Door Jamb.

Step2: Measure and cut Doorstep Flashing (106) to

fit in between Door Jambs. Position the Door-

step Flashing in between the Door Jambs at

bottom of doorway, nail through top of flashing

using three 30mm Clouts. Repeat with the

Overdoor Flashing (105).

Step 4: Fit the two short front Corner Flashings over corner

Ribs and rivet in place using six rivets per flashing.

Fit the two longer back Corner Flashings over cor-

ner Ribs and rivet in place using six rivets ensuring

the flashing is flush with the top plate. When fitting

right hand Corner Flashing on the front wall, ensure

it is parallel with the Door Jamb.

Inhaltsverzeichnis

Andere Riverlea Außenlagerung Handbücher

Riverlea

Riverlea SmartStore SM2020 Bedienungsanleitung

Riverlea

Riverlea Smartstore SS2020 Bedienungsanleitung

Riverlea

Riverlea Duratuf Garrison Sheds PL84 Bedienungsanleitung

Riverlea

Riverlea Duratuf Guardian SHEDS GS63 Bedienungsanleitung

Riverlea

Riverlea Duratuf KIWI SHEDS MK4A Bedienungsanleitung

Riverlea

Riverlea Duratuf Guardian Sheds GL57 Bedienungsanleitung

Riverlea

Riverlea Duratuf Guardian SHED SGS73 Bedienungsanleitung

Riverlea

Riverlea SmartStore SM3015 Bedienungsanleitung

Riverlea

Riverlea SmartStore SM2520 Bedienungsanleitung

Riverlea

Riverlea Duratuf Garrison Sheds PL46 Bedienungsanleitung

Riverlea

Riverlea Duratuf Garrison Sheds PL43 Bedienungsanleitung

Riverlea

Riverlea Duratuf SENTRY SHEDS SG2020 Bedienungsanleitung

Riverlea

Riverlea Duratuf Guardian Sheds GG101 Bedienungsanleitung

Riverlea

Riverlea SmartStore SM2007 Bedienungsanleitung

Riverlea

Riverlea Duratuf KIWI SHEDS MK4C Bedienungsanleitung

Riverlea

Riverlea Duratuf SS2010 Bedienungsanleitung

Riverlea

Riverlea Duratuf Gurdian Sheds GS62 Bedienungsanleitung

Riverlea

Riverlea Smart Store SM1510 Bedienungsanleitung

Riverlea

Riverlea SmartStore SM3025 Bedienungsanleitung

Riverlea

Riverlea SmartStore SS2520 Bedienungsanleitung

Riverlea

Riverlea Duratuf Guardian SHED SG3025 Bedienungsanleitung

Riverlea

Riverlea Duratuf Garrison Sheds PS62 Bedienungsanleitung

Riverlea

Riverlea Rustics NEBRASKA Bedienungsanleitung

Riverlea

Riverlea CEDAR SHED NOTTINGHAM Bedienungsanleitung

Beliebte Außenlagerung Handbücher anderer Marken

USP

USP DURAMAX 10 Ft x 8 Ft StoreMax Plus Bedienungsanleitung

TYGO

TYGO Nyland Bedienungsanleitung

Duratuf

Duratuf GL105 Bedienungsanleitung

Viking

Viking SD5300SS Technisches Handbuch

USP

USP DURAMAX Apex Pro 10.5 Ft x 8 Ft 40116 Bedienungsanleitung

ModuLaro

ModuLaro Lojo WC202200 Bedienungsanleitung

Lifetime

Lifetime 6418 Bedienungsanleitung

rollaway container

rollaway container ARPCA24 Bedienungsanleitung

Duratuf

Duratuf Havelock Bedienungsanleitung

X-METAL

X-METAL 4065 Bedienungsanleitung

Outdoor Life Products

Outdoor Life Products FP2030 F Bedienungsanleitung

Royalcraft

Royalcraft Faro 295L Storage Box Bedienungsanleitung

Rubbermaid

Rubbermaid 5L45 Bedienungsanleitung

garofalo

garofalo TUSCANY EVO Bedienungsanleitung

OLT

OLT GS84D-FJ-Plywood Bedienungsanleitung

Duratuf

Duratuf Kiwi MK1 Bedienungsanleitung

Eden

Eden CA2988 Bedienungsanleitung

Palram

Palram CANOPIA RUBICON 6x10 Administratorhandbuch