RIVI EV35 Bedienungsanleitung

EV35 Access Point

Quick Setup Guide

This Quick Setup Guide provides step-by-step instructions on how to

field-install the EV35 access point (AP). For detailed information on

planning the installation, performing a site survey, and operating the

EV35.

WARNING! Only trained and qualified personnel should be allowed to

install, replace, or service this equipment.

WARNING! Installation of this equipment must comply with local and

national electrical codes.

CAUTION! Form a 80-mm to 130-mm (3-in. to 5-in.) drip loop in any

cable that is attached to the AP or the building. This will prevent water

from running along the cable and entering the AP or the building where

the cable terminates.

CAUTION! Be sure that grounding is available and that it meets local

and national electrical codes. For additional lightning protection,

use lightning rods and lightning arrestors.

CAUTION! Make sure that proper lightning surge protection

precautions are taken according to local electrical code.

CAUTION! RIVI strongly recommends that you wear eye

protection before mounting the EV35.

Required Hardware and Tools

•No. 2 Phillips screwdriver

•Small flat-blade screwdriver

•Wide flat-blade screwdriver

•Torque wrench or torque screwdriver with sockets

•Long-nose pliers

•Electrical wire stripping and terminal crimping pliers

•Pipe or pole, or a sturdy flat surface

•Electric drill with drill bits and customer-supplied wall anchors,

flat washers, and hex nuts for flat-surface mount

Package Contents

A complete EV35 field installation package includes all of the following

items:

•EV35 Access Point

•M25 data cable gland

•Ground wire with lug

•Pole/Wall Mount Bracket Kit

•Two steel pipe clamps

•Declaration of Conformity/Regulatory

Statement

FIGURE 1 EV35 Package Contents

1. EV35 Access Point

2. M25 data cable gland

3. Ground wire with lug

4. Pole/Wall Mount Bracket Kit

Unleashed Network Configuration

Setup Using the Unleashed Mobile App

To perform setup using the Unleashed Mobile App, download the iOS

or Android app from the app store.

Scan here for IOS app

3. Launch the app, and follow the on-screen instructions to configure

your Unleashed network(s).

FIGURE 2 Unleashed Mobile App for iOS and Android

FIGURE 3 Configuring Unleashed from the Mobile App

Setup Using a Web Browser

1. As soon as the Unleashed AP is powered on and connected to the

local network, it boots up and begins broadcasting a temporary

unencrypted WLAN named “Configure.Me-[xxxxxx]” from both

radios.

2. Using your client’s Wi-Fi connection settings, select and associate

to the “Configure.Me-[xxxxxx]” WLAN.

3. Launch a web browser and enter the following into the browser’s

URL bar: unleashed.rivinetworks.com, and press Enter.

4. You will be redirected to the Setup Wizard. Complete the steps in

the Setup Wizard and click Finish.

Page 1 of 4

Mark No: UK00003636458 Published Jan 2022,

Part Number 800-72972-301 Rev A

1. As soon as the Unleashed AP is powered on and connected to the

local network, it boots up and begins broadcasting a temporary

unencrypted WLAN named “Configure.Me-[xxxxxx]” from both

radios.

2. Using your client’s Wi-Fi connection settings, select and associate

to the “Configure.Me-[xxxxxx]” WLAN.

Scan here for Android app

FIGURE 4 Complete the Setup Wizard to set up your

Unleashed network

5. Once the Setup Wizard is finished, a “Configuring system settings

and rebooting” progress screen appears. Wait until the process is

complete.

6. Connect to the WLAN that you configured in the Setup Wizard,

and click OK to reconnect. You will be redirected to the Unleashed

7. Enter your Admin Name and Password to login.

FIGURE 5 The Login page

8. Upon successful login you will be presented with the Unleashed

Dashboard, which displays an overview of your Unleashed

network.

Mounting Instructions

Connecting and Sealing the RJ-45 Cables

Connect and seal the RJ-45 cables using the M25 data cable glands.

WARNING! Do not use any PoE injector not tested and approved by

RIVI to power the EV35 Access Point.

FIGURE 6 EV35 LEDs and Ports

1. Feed the end of the cable through the sealing nut, rubber O-ring,

clamping ring assembly, and cable gland base, as shown in Figure 7.

NOTE: Do not seat the clamping ring and rubber O-ring into

the gland body until the gland body has been torqued to

specifications.

FIGURE 7 RJ-45 Cable and Gland Assembly

1. Cable gland

base

2. Clamping ring

3. Rubber O-

ring

4. Sealing nut

2. Use a wide flat-blade screwdriver to remove the required (PoE IN)

blanking cap from the AP.

3. Connect the cable to the Ethernet port on the AP.

4. Tighten the cable gland base into the AP chassis to 7 N.m or 62 in-

lbs.

5. Wrap the clamping ring assembly around the rubber O-ring. Make

sure that the clamping ring assembly fully encloses the rubber O-

ring.

6. Seat the clamping ring assembly and rubber O-ring in the cable

gland base.

7. Hand-tighten the sealing nut.

Attaching the Mounting Bracket to a Flat Surface

1. The AP mounting bracket attaches to the AP using a captive screw.

Use a medium flat-blade or No. 2 Phillips screwdriver to loosen

the captive screw, as shown in Figure 8, and pull up on the end

of the bracket to remove the bracket from the AP, as shown in

Figure 8.

FIGURE 8 Removing the Mounting Bracket

1. Loosen the captive

screw

2. Pull up on the end of the

bracket

2. Using either of the two options shown in Figure 9, hold the mounting

bracket at the location on the mounting surface where you want

to mount the AP. Use the holes on the mounting bracket as a

template to mark the locations of the mounting holes.

NOTE: The mounting bracket can be mounted to a vertical or

horizontal surface to support the AP in the required orientation.

Page 2 of 4

Mark No: UK00003636458 Published Jan 2022,

Part Number 800-72972-301 Rev A

FIGURE 9 Mounting Bracket on a Flat Surface

1. Horizontal mounting 2. Vertical mounting

3. Remove the mounting bracket from the mounting surface.

Drill holes required for the customer-supplied mounting

hardware. Attach the mounting bracket to the flat surface using

the mounting hardware.

6. Using the mounting hardware instructions, tighten the

hardware to secure the mounting bracket.

7. Continue with Mounting the AP on page 3.

Attaching the Mounting Bracket to a Pole

The AP mounting bracket attaches to the AP using a captive

screw. Loosen the screw and pull up on the end of the bracket to

remove the bracket from the AP, as shown in Figure 8 on page 2.

Insert the open end of one steel clamp into two of the slots on the

mounting bracket.

NOTE: The mounting bracket can be mounted to a vertical or

horizontal pole to support the AP in the required orientation.

Using either of the two options shown in Figure 10, use the clamps

to attach the mounting bracket to the pole. Tighten the clamps to

3 N.m or 27 in-lbs, or per manufacturer’s specifications if the

factory-supplied clamps are not used.

If necessary, daisy-chain the other steel clamps to accommodate

larger poles.

FIGURE 10 Mounting Bracket on a Pole

1. Horizontal pole

mounting

2. Vertical pole mounting

5. Continue with Mounting the AP.

Mounting the AP

1. Snap the AP back onto the mounting bracket, as shown in Figure 11,

and use a medium flat-blade or No. 2 Phillips screwdriver to

tighten the captive screw to 1.1 N.m or 10 in-lbs to secure the

bracket to the AP, as shown in Figure 11.

FIGURE 11 Attaching the Mounting Bracket to the AP

1. Snap the AP to the

mounting bracket

2. Tighten the captive

screw

2. Optional Step: If you also need to lock the mounting bracket to the

AP, then use an appropriately sized screwdriver to screw the

customer-supplied locking stainless steel 6-mm M3 panhead

security screw through the mounting bracket and into the AP

chassis.

CAUTION! Make sure that the customer-supplied locking stainless

steel M3 panhead security screw is no longer than 6mm. If the

security screw is longer than 6mm, it can damage the AP chassis.

FIGURE 12 Locking the Mounting Bracket to the AP

You have completed mounting the AP to the mounting bracket.

Powering the AP with DC Power

The AP can accommodate two sources of power: PoE (48V) power and

12V DC.

The AP can draw power from the Ethernet input as a Class 4 device,

providing a maximum of 18 W to the system. Alternately, power can be

supplied through a customer-provided 12V DC power supply (12V DC

preferred, 7-20V DC acceptable) that will connect to a two-pin terminal

block. The terminal block is accessible through a water-tight gland on

one end of the unit. The terminal block connection has surge and

polarity protection to protect against inserting the wrong polarity leads

into the terminal block.

NOTE: If both the PoE and DC ports are used, separate cable glands

must be used for each port. Additional cable gland (Part Number

902-0183-0000) can be be purchased.

NOTE: When both the 12V DC and the 48V PoE power are active, the AP

will prioritize the 12V DC power.

CAUTION! Ensure that the DC power source does not exceed 20V DC.

1. Install the DC power supply as described in the DC power

supply accessory installation guide.

2. Connect the power cord to a DC power source.

3. Verify that the PWR LED is a steady green.

Earth Grounding the AP

CAUTION! Make sure that earth grounding is available and that it meets

local and national electrical codes. For additional lightning protection,

use lightning rods and lightning arrestors.

NOTE: The color coding of ground wires varies by region. Before

completing this step, check your local wiring standards for guidance.

Using the factory-supplied ground wire and ground screw and washer

set, connect a good earth ground to the AP chassis ground point.

CAUTION! The EV35 includes one 9-mm stainless steel M6x1 earth

ground screw with split lock and flat washers. Make sure that any

replacement screw is no longer than 9 mm. If a screw is longer than 9

mm, it can damage the AP chassis.

Page 3 of 4

Mark No: UK00003636458 Published Jan 2022,

Part Number 800-72972-301 Rev A

FIGURE 13 Connecting a Good Earth Ground to the AP

1. Earth ground screw

Installing a USB Dongle

To install a USB dongle (for example, an IoT radio device such as BLE,

802.15.4, Z-wave, or similar), remove the two 3-mm hex screws,

remove the cap, and insert the dongle into the USB port.

Once installed, replace the cap and the hex screws, and tighten the

screws to 0.79 N.m or 7 in-lbs.

NOTE: If required, a larger USB dongle cap can be purchased

separately. The maximum dimensions of the USB dongle that can be

inserted (with the large USB dongle cap, part # 902-0127-000) are 6

cm x 2 cm x 1.1 cm. Max Power: 450mW (SiLabs EM3578 max current

draw at +20 dBm is 80mA over a 3.3V rail).

FIGURE 14 Installing a USB Dongle

Troubleshooting

CAUTION! If required, you can reset the AP to its factory default

settings by pressing the reset button located inside the PoE IN port.

Use the tip of a pen or a 3-mm flat-blade screwdriver to press the reset

button. Press and hold the reset button for 4 seconds or longer to

restore to factory defaults. DO NOT RESET THE AP TO FACTORY

DEFAULT SETTINGS UNLESS SO INSTRUCTED. (Doing this resets the

AP IP address to 192.168.0.1.)

NOTE: After a reset, you can access the internal AP web interface

using https://192.168.0.1. Your device must use any other address

from 192.168.0.2 through 192.168.0.254, with subnet mask

255.255.255.0. The username is super, and the password is sp-admin.

Refer to the Outdoor Access Point User Guide for information on

configuring and operating the AP. This document is available at

https://support.rivinetworks.com.

Page 4 of 4

Mark No: UK00003636458 Published Jan 2022,

Part Number 800-72972-301 Rev A

Andere RIVI Drahtloser Zugangspunkt Handbücher

RIVI

RIVI RV75 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung