Robe PATT 2017 Bedienungsanleitung
Version 1.5
2
Table of contents
1. Safety instructions ......................................................................................................... 3
2. Description of the xture .............................................................................................. 4
3. Installation....................................................................................................................... 5
3.1 Mounting the PATT 2017 ........................................................................................... 5
3.2 Connecting the PATT 2017 with the PATT Driver....................................................... 5
4. Technical specications ................................................................................................ 6
3
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY
BEFORE INSTALLING THE PRODUCT .
1. Safety instructions
CAUTION!
The PATT 2017 was designed for indoor use only.
The product is for professional use only, it is not for household use.
This product has left our premises in absolutely perfect condition. In order to maintain this condition and to
ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning
notes written in this manual.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this
manual or any unauthorized modication to the product.
If the device has been exposed to drastic temperature uctuation (e.g. after transportation), do not switch it on
immediately. The arising condensation water might damage your device. Leave the device switched o until
it has reached room temperature.
The pixel PATT should be operated with the PATT Driver only.
The PATT 2017 becomes hot during its operation, a
llow it to cool prior
to manipulation.
The PATT 2017 unit never must be covered with cloth or other materials during
operation.
Refer servicing to qualied service personnel.
Warning! Risk Group 2 LED product according to EN 62471
LED light emission. Risk of eye injury. Do not look into the beam at short distance of
the of the product. Do not view the light output with optical instruments or any
device that may conncentrate the beam.
The light source contains blue LEDs.
When choosing the installation spot, please make sure that the PATT 2017 are not exposed to extreme heat,
moisture or dust.
Operate the PATT 2017 only after having familiarized with its functions. Do not permit operation by persons not
qualied for operating the PATT 2017. Most damages are the result of unprofessional operation!
Please use the original packaging if the PATT 2017 is to be transported.
Please consider that unauthorized modications on the xture are forbidden due to safety reasons!
4
2. Description of the xture
Pixel positions:
1 - Mounting yoke
2 - Parabolic aluminium reector
3 - Fan
4 - Control Input (4-pin XLR)
5 - Control box
6 - Tilt lock
5
3. Installation
The PATT 2017 must be installed by a qualied electrician in accordance with all
national and local electrical and construction codes and regulations.
3.1 Mounting the PATT 2017
The xture can be rigged to the truss or fastened to the oor stand via a mounting yoke. The hole of diameter
of 13 mm in the yoke serves for fastening a clamp (or a spigot) to the yoke.
Note: the spigot has to be inserted into the oor stand and always secured.
For overhead installation the PATT 2017 has to be always secured to the truss by means of a safety wire (that
can hold at least 10 times the weight of the xture) which is fastened to the truss and around mounting yoke
of the PATT 2017.
3.2 Connecting the PATT 2017 with the PATT Driver
1. Disconnect the PATT Driver from mains.
2. Connect the PATT 2017 to the PATT Driver by means of the 4-pin data cable.
3. Connect the PATT Driver to mains and make desired setting.
ALWAYS DISCONNECT THE PATT DRIVER FROM MAINS BEFORE CONNECTING/DISCONNECTING
THE PATT 2017.
Please see the user manual of the PATT Driver for more detailed information about its operation
6
For CE only: If you do not use the original Robe Data Cable 4-pin XLR for connection between PATT 2017 and
PATT Driver, the ferrite RRC 17-11-28-M-K5B (Robe P/N 13051799) should be installed on the 4-pin XLR cable
closely to the PATT 2017 as shown on the picture bellow.
If you use the original Robe 4-pin XLR cable, this ferrite is part of the cable and you do not need to install
another ferrite on the cable.
4. Technical specications
Input voltage: 48V
Max. power consumption: 210W
Compatible control driver: PATT Driver
Light source: 7x RGBW LED multichip
LED life expectancy: min. 20 000 hours
Typical lumen maintenance: 70% @ 20 000 hours
Optical System: parabolic aluminium reector with high reectivity coating
Control input: Locking 4-pin XLR (male)
Max. length of cable between
PATT Driver and PATT 2017: 10m
Mounting Points: Mounting horizontally or vertically via mounting yoke (360° tilt range)
Rigging: M12 mounting for clamp or spigot.
Operation position: any
Ingress protection: IP20 (for dry location only)
Weight: 10.3 kg
Max. surface temperature: 65°C (at 45°C ambient)
Maximum ambient temperature: 45 °C
Total heat dissipation (calculated):716 BTU
Min. distance from ammable surfaces: 0.2 m
Min. distance of illuminated objects: 0.2 m
Ferrite RRC 17-11-28-M-K5B
7
Dimensions (mm)
Wiring of control input:
Optional accessories
(P/N 10980374) Tripod for PATT 2013/2017, pixelPATT
(P/N 1098 0259) Floor Stand for PATT 2013, picklePATT
(P/N 1098 0260) Spigot for PATT 2013/2017/picklePATT, pixelPATT
(P/N 13052797) Data cable 4 pin XLR 10m, ferrite, EU
(P/N 13052798) Data cable 4 pin XLR 5m, ferrite, EU
(P/N 13052799) Data cable 4 pin XLR 10m, US
(P/N13052800) Data cable 4 pin XLR 5m, US
(P/N 17030386) Doughty Trigger Clamp
(P/N 99011963) Safety wire 35 kg
(P/N 13051799) Ferite RRC 17-11-28-M-K5B
(P/N 10055002) PATT Driver
1 - 0V
2 - Signal -
3- Signal +
4- +48V
8
Beam distribution
Copyright © 2017-2018 Robe Lighting - All rights reserved
Specications are subject to change without notice.
April 19, 2018
Made in ROBE Lighting s.r.o., Palackého 416, 757 01 Valašské Meziříčí, Czech Republic
Inhaltsverzeichnis
Andere Robe Beleuchtungsausrüstung Handbücher
Robe
Robe Robin 300E Spot Bedienungsanleitung
Robe
Robe DigitalSpot 7100 DT Bedienungsanleitung
Robe
Robe LightDome 575 Bedienungsanleitung
Robe
Robe RoboSpot Bedienungsanleitung
Robe
Robe Color Mix 250 AT Series Bedienungsanleitung
Robe
Robe ColorSpot 250 AT Bedienungsanleitung
Robe
Robe Wash 575XT Bedienungsanleitung
Robe
Robe Robin 100 LEDBeam Wireless DMX CRMX Bedienungsanleitung
Robe
Robe Digital Spot 3000 DT II Bedienungsanleitung
Robe
Robe ColorWash 250 AT Bedienungsanleitung
Robe
Robe DigitalSpot 7000 DT Bedienungsanleitung
Robe
Robe ROBIN Pointe Bedienungsanleitung
Robe
Robe Robin MMX Blade Bedienungsanleitung
Robe
Robe Anolis Eminere Inground 2 Wireless DMX Bedienungsanleitung
Robe
Robe Robin 600 Purewhite WIreless DMX Bedienungsanleitung
Robe
Robe Color Sport 1200 Profile Bedienungsanleitung
Robe
Robe Anolis Ambiane XP56 Bedienungsanleitung
Robe
Robe Anolis ArcDot-US Bedienungsanleitung
Robe
Robe CitySource 96 Bedienungsanleitung
Robe
Robe Robin 600E Beam Bedienungsanleitung
Beliebte Beleuchtungsausrüstung Handbücher anderer Marken
Qazqa
Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung
Commercial Electric
Commercial Electric 54568141 Bedienungsanleitung
CREE LIGHTING
CREE LIGHTING 304 Series Bedienungsanleitung
Goobay
Goobay 49867 Bedienungsanleitung
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Bedienungsanleitung
Alkalite
Alkalite Krypton KT-81 Bedienungsanleitung
