Robustel GoRugged R2000 Bedienungsanleitung

Hardware Installation Quick Guide

R2000--Industrial Cellular VPN Router

Package Checklist

Before installing theR2000 router, verify that the package contains the following items:

Robustel R2000 Router

Terminal Block for Power

Document and Software CD

Optional Accessories

AC/DC Power Supply Adapter

Rubber SMA Antenna

35mm Din-Rail mounting kit or Wall mounting kit

Notify your sales representative if any of the above items is missing or damaged.

Reset Button

Restore the R2000 to factory default settings by using a pointed object (such as a Pointed pen) to keep

pushing the button about 16 seconds once power on, until all the LED light blink one by one recurrently.

When all the LED light blinks hold on 2 seconds, it means that the router loads default successfully.

In addition, reboot R2000 by pushing the button for 2~7 seconds under working status.

Ethernet Port

Each Ethernet port has two LED indicators. The yellow one is Link indicator and the green one doesn’t

mean anything. There are three status of Link indicator.

Indicator

Status

Description

Link Indicator

Off

Connection is down.

Connection is up.

Blink

Data is being transmitted

Environment Requirements

Power Input: 9 to 26 VDC

Power Consumption: Idle: 100 mA @ 12 V, Data Link: 500 mA (peak) @ 12 V

Operating Temperature: -40 to +85°C (R2000-4L support -40 to +75°C)

Operating Humidity: 5 to 95% RH

Hardware Introduction

As shown in the following figures, R2000 router has two Ethernet ports (2xLAN or

1xLAN+1xWAN) and two cellular SIM card slots.



Router shall be grounding reliably

under the rule which in order to

avoid lightning strike damage.



When use the power adapter, please

note the power polarity.



Please pay attention to waterproof in

the storage, transportation and

operation environment.



Suggest to mounting the router on a

horizontal flat surface.



If warranty label was damaged in

warranty period of product, no free

maintenance.

Caution

E-mail: sup[email protected]om

Hardware Installation

Step 1: After unpacking the unit, please refer to the following figure insert the SIM into the R2000 router.

Please note: recommended torque for inserting is 0.5N.m and the maximum torque is 0.7N.m

Step 2: Connect router with an external SMA antenna. Make sure the antenna is within correct frequency

range and is screwed tightly.

Please note: recommended torque for mounting is 0.35N.m

Step 3: Use a wire connect the ground screw of router to ground surface before connecting devices.

(Optional)

Step 4: Use a standard cross-over Ethernet cable to connect R2000 to PC with Eth0 or Eth1 port.

Step 5: The router may be placed on a horizontal surface such as a desktop, mounted on a DIN-rail, or

mounted on the wall.

Wall Mount

Use 4 pcs of M2.5 screw to fix the router on the two metal plates. And then use 2 pcs of M3

screw with point-end to mount the router with two metal plates on the wall.

Please note: recommended torque for mounting is 0.5N.m and the maximum torque is 0.7N.m

Din Rail

Mount the router on a DIN rail with 3 pcs of M3 screws, and then hang the DIN-Rail on the

holder. You need to choose a standard holder.

Please note: recommended torque for mounting is 1.0N.m and the maximum torque is 1.2N.m

Step 6: Connect the power supply to the R2000 router. There are two lines connecting to the power

supply adapter, as it illustrates on the power supply adapter label, the line printed with letters

needs to be connected with the positive polarity, and the striped line needs to be connected

with the negative polarity.

LED Indicators

Name

Color

Status

Function

RUN

Green

Blinking

Router is ready.

Router is starting.

Off

Router is power off.

PPP

Green

Blinking

PPP Indicator: Null

PPP Indicator: PPP connection is up.

Off

PPP Indicator: PPP connection is down.

USR

Green

Blinking

SIM: using backup SIM card.

NET: register to a low level network.

Off after blinking

SIM: working fine.

NET: working fine.

Light up

OpenVPN: OpenVPN is connected.

IPSec: IPSec is connected.

GRE: GRE is connected.

Off after lighting up

OpenVPN: OpenVPN is disconnected.

IPSec: IPSec is disconnected.

GRE: GRE is disconnected.

Green

Signal level: 21-31 (Perfect signal level).

Yellow

Signal level: 11-20 (Average signal level).

Red

Signal level: 1-10 (Exceptional signal level).

When the network is disconnected, those three signal LEDs are designed as a

binary combination code to indicate a series of error report.

(Green Yellow Red) On: 1 Off: 0

001 AT command failed

010 no SIM card detected

011 it need to enter the PIN code

100 it need to enter the PUK code

101 registration failed

110 something wrong happened in the module

Insert SIM Card

Wall Mount

Din Rail

Andere Handbücher für GoRugged R2000

Andere Robustel Netzwerk-Router Handbücher

Robustel

Robustel R2000 Ent Bedienungsanleitung

Robustel

Robustel R1511 Bedienungsanleitung

Robustel

Robustel GoRugged R3000 Lite Bedienungsanleitung

Robustel

Robustel GoRugged R2000 Bedienungsanleitung

Robustel

Robustel EG5200 Bedienungsanleitung

Robustel

Robustel R2110 Bedienungsanleitung

Robustel

Robustel GoRugged R3000 Lite Bedienungsanleitung

Robustel

Robustel R2110 Bedienungsanleitung

Robustel

Robustel R1511 Bedienungsanleitung

Robustel

Robustel GoRugged R3000 Lite Bedienungsanleitung

Robustel

Robustel GoRugged R3000 Lite Bedienungsanleitung

Robustel

Robustel GoRugged R3000 Lite Bedienungsanleitung

Robustel

Robustel R1510 Bedienungsanleitung

Robustel

Robustel R1520 Bedienungsanleitung

Robustel

Robustel R3000-3P Bedienungsanleitung

Robustel

Robustel GoRugged R2000 Bedienungsanleitung

Robustel

Robustel GoRugged R3000 Lite Benutzerhandbuch

Robustel

Robustel GoRugged R3000 Lite Bedienungsanleitung

Robustel

Robustel GoRugged R2000 Bedienungsanleitung

Robustel

Robustel EV8100 Bedienungsanleitung

Robustel

Robustel GoRugged R2000 Bedienungsanleitung

Robustel

Robustel GoRugged R2000 Bedienerhandbuch

Robustel

Robustel GoFixed W800 Bedienungsanleitung

Robustel

Robustel GoRugged R3000 Lite Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise