ROC Superslim Leitfaden

Manual and Warranty ·Manuel et Garantie ·Handbuch und Garantieschein ·Manual y Garantía

Important Monster®

Performance and Safety Tips

Listen Responsibly

To avoid hearing damage, make sure that the

volume on your music player is turned down

before connecting your headphones. After

placing headphones in / on your ears, gradually

turn up the volume until you reach a comfortable

listening level.

Noise levels are measured in decibels (dB), exposure

to any noise at or above 85 dB can cause gradual

hearing loss.

Monitor your use; hearing loss is a function of

loudness versus time. The louder it is, the less

time you can be exposed to it. The softer it is, the

more time you can listen to it.

This decibel (dB) table compares some common

sounds and shows how they rank in potential

harm to hearing.

SOUND NOISE LEVEL (dB) EFFECT

Whisper 30 Very quiet

Quiet Oce 50–60 Comfortable hearing levels are under 60 dB

Vacuum Cleaner, Hair Dryer 70 Intrusive; interferes with telephone conversations

Food Blender 85–90 85 dB is the level at which hearing damage (8 hrs.) begins

Garbage Truck,

Cement Mixer

100 No more than 15 minutes of unprotected exposure

recommended for sounds between 90–100 dB

Power Saw, Drill/Jackhammer 110 Regular exposure to sound over 100 dB of more than

1 minute risks permanent hearing loss

Rock Concerts (varies) 110–140 Threshold of pain begins around 125 dB

Chart information obtained from www.nidcd.nih.gov/health/education/teachers/pages/common_sounds.aspx

ENGLISH

Get the most out of your equipment and enjoy

great audio performance even at safe levels. Our

headphones will allow you to hear more details at

lower volume levels than ever before.

Learn how to establish a safe listening level and

review other important safety guidelines from the

Consumer Electronics Association at www.ce.org.

Important information on how to prevent Noise-

Induced Hearing Loss (NIHL) and a comprehensive

list of which noises can cause damage can be

found on the Deafness Research Foundation’s

website, www.drf.org.

Physiology of the Ear and Hearing

For additional information on what loud noises do to your ear and

chart reference www.abelard.org/hear/hear.php#loud-music

Use Responsibly

Do not use headphones when it’s unsafe to do so –

while operating a vehicle, riding a bike, crossing

streets, or during any activity or in an environment

where your full attention to your surroundings

is required.

It‘s dangerous to drive while wearing headphones,

and in many places, illegal because it decreases

your chances of hearing life-saving sounds outside

of your vehicle, such as another car’s horn and

emergency vehicle sirens.

Please avoid wearing your headphones while

driving. Use one of Monster’s FM transmitters to

listen to your mobile media devices instead.

Headphones“Break-in”

Break in time for headphones? We’re kidding,

right? No we’re not. Like any high performance

product, whether it’s cars or headphones, they’re

mechanical devices that settle in after use. Your

new headphones will sound incredible out of the

box, but will“mellow” out after use and sound even

better. We recommend playing them for 8 hours.

After 20 hours of playing, they should be fully

broken in. Enjoy.

Malleus Cochlear Nerve

Stapes

Tympanic

Membrane

Auditory Canal Cochlea

Incus

Vestibule

To Nose/Throat

ENGLISH

Battery

If applicable, battery must be recycled or disposed

of properly.

Information to consumers in application

of EU WEEE Directive 96/2002

This product is subject to European Union

regulations that promote the re-use

and recycling of used electrical and electronic

equipment. This product required the extraction

and use of natural resources and may contain

hazardous substances. The symbol above, on the

product or on its packaging, indicates that this

product must not be disposed of with your other

household waste. Instead, it is your responsibility

to dispose of your waste equipment by handing

it over to a designated collection point for the

recycling of waste electrical and electronic

equipment. The separate collection and recycling

of your waste equipment at the time of disposal

will help to conserve natural resources and ensure

that it is recycled in a manner that protects human

health and the environment. For more information

about where you can drop o your waste

equipment for recycling, please contact your local

city oce, your household waste disposal service,

or the store from which you purchased the product.

For more information about Monster products,

please visit us at: www.MonsterProducts.com.

Monster®Service

Have a Problem with Your

Headphones? Our Customer

Service Team is here for you.

Please don’t return headphones to your retailer,

CALL our customer service center, 1-877-800-8989

for United States or Latin America, or email us at

www.MonsterProducts.com/service/. For Canadian,

European, and Asian Pacic customer service

numbers, please see the“Telephone Numbers”

section in the following “Limited Warranty for

Consumers”. Our team of experts will assist you

with all questions and technical diculties.

We stand behind our products. Monster

headphones deliver the best in sound, quality,

and design.

Thank you for your purchase.

Download the complete manual at:

www.MonsterProducts.com

ENGLISH

Product Overview

1. Indicator light

2. Charge jack

3. Volume + / Track Forward

4. Multifunction button

(Power On/O, Pairing,

Activate Voice Dialing)

5. Volume - / Track Backward

6. Microphone

INDICATOR LIGHT DESCRIPTION VOICE PROMPTS

Power on Stays blue 1 second Power on

Power o Stays red 2 seconds Power o

Standby (connected) Blink blue once every 5 seconds /

Pairing Flashes Red and Blue alternately Pairing

Incoming call Flashes blue continuous /

Charging Stays on blue while charging /

Guide to Indicator Lights

1 2

ENGLISH

Basic operation

Charge the Battery

Your ROC SuperSlim initially has enough power to

complete the pairing and a few calls. When battery

is low, you will hear warning tone and indicator

light changes to red. The headphone includes a

Micro USB cable that can be connected to your

computer or other device made for USB charging.

Plug the Micro USB end of the included USB cable

into the USB micro port charger connector on the

right channel side of the headphone. Plug the

other end into a USB port on your computer or

other devices made for USB charging. The indicator

light will be blue while charging. Once fully

charged, the indicator light will be o. Charge time

is approximately 1.5 hours on an empty battery.

Note: The lifetime of the battery will be signicantly

reduced if your headphone is left uncharged for a

long period. We recommend that you recharge your

headphone at least once a month.

Power On/ Power O

Press the Multifunction button for about 1 second

to power on the headphone. To power o the

headphone, press the Multifunction button for

about 3 seconds.

Volume Control

Press the Volume “+” or“-” to turn volume up

or down, you hear beep once you reach the

maximum volume or minimum volume.

Pairing

Pair One Phone

1. Press and hold the Multifunction button for

about 5 seconds until indicator light ashes

blue and red alternately, you hear“Power

on”and “Pairing”. Now

headphone

is in

pairing mode.

2. Activate Bluetooth® on your phone and set it

to search for new devices.

3. Select “SuperSlim”. If your phone

asks, enter

0000 (four zeros) for the passcode or accept

the connection. The indicator light stops

ashing red and blue once successfully

paired, you hear “Paired, phone 1 connected”.

Some phone list an option to“Play through

earphone”, select to use the

headphone

Note: When you unbox the headphone and power

it on for the rst time, it will enter to pairing mode

automatically.

ENGLISH

Pair Another Phone

Multipoint technology enables you to pair another

phone and take a call from either.

To pair with another mobile phone, power o

the headphone, then follow the steps for“Pair

one phone”. After pairing successfully, restart the

headphone

to connect to 2 paired mobile phone

automatically and manually.

Note: You may need to connect the second

phone manually.

Call

Answer a Call: Press the Multifunction button once.

Reject a Call: Press and hold the Multifunction

button for about 1 second.

End a Call: Press the Multifunction button once.

Redial the Last Call: Press Volume”+”and“-” for

about 3 seconds in standby mode. The mobile

phone will redial the last call number.

Mute On/O: Press the Volume “-”for about

3 seconds to mute on/o.

Switch Between the Headphone and Phone:

Press the Multifunction button for about 1 second

during a call, the call will be switched to the mobile

phone, redo this operation again, the call will be

switched to the headphone.

End Current Call and Answer New Call: When a

new call rings during a call, press the Multifunction

button once to answer new call and end current

call simultaneously.

On Hold Current Call and Answer New Call:

When a new call rings during a call, double press

the Multifunction button to hold current call and

answer new call. To switch between held call and

active call, double press the Multifunction button.

Activate Voice Dialing: Double press the

Multifunction button to trigger the voice dialer,

this function varies with user’s smartphone.

Music

Play / Pause Music: Press Multifunction button

once to play / pause music. (Some phones may

require you to start a media player rst).

Track Back / Forward: Press the Volume“-” for

1 second once to skip track backward, press Volume

“+”for 1 second once to skip track forward.

Switch Music and Call: When a call rings during a

music playing, the music automatically pauses to

allow you to answer or ignore the call. Once the call

is ignored or ends, the music is resumed.

ENGLISH

More Features

Battery Indicator

When the headphone is connected to a device with

iOS system, a battery indicator will appear at the

upper right of the system, indicating battery status

of the headphone.

Auto Power-O

When the distance between the headphone and

the mobile phone is beyond eective range, a

warning tone will be alerted and headphone will try

to reconnect with the mobile phone for 10 minutes.

If no phone is reconnected within 10 minutes, the

headphone will go to connectable mode and wait

for 5 more minutes before automatically power o.

Automatic Connection After

Powering On

When the headphone and phone have been

paired once, they will automatically connect when

the headphone is on and Bluetooth is activated

on the phone.

Connection Standby

After successful pairing and connection, you will

hear the voice prompt “Phone 1 connected”. The

headphone will be in turning on mode or standby

mode automatically and the blue LED will ash

once every 5 seconds. When the phone disconnects

the headphone, you will hear the disconnect tone.

Reset Paired Device(s)

Go to the Pairing mode (hold the Multifunction

button for 5 seconds from Power o state), then

hold the Volume “-” to reset the paired device(s),

indicator light ashes blue and red alternatively

and rapidly few times, you will also hear the tone.

Hardware Reset

Plug the Micro USB cable into the USB micro port

of headphone to connect it to the computer or

other device made for USB charging to have the

hardware reset.

Certication

FCC ID: RJE190653

This device complies with Part 15 of FCC Rules.

Operation is subject to the following two

conditions: (1) This device may not cause harmful

interference, and (2) This device must accept any

interference received, including interference

that may cause undesired operation. Changes or

modication not expressly approved by the party

responsible for Compliance could void the user’s

authority to operate the equipment. Connecting of

peripherals requires the use of grounded shielded

ENGLISH

signal cables. The socket-outlet shall be installed

near the equipment and shall be easily accessible.

NOTE: This equipment has been tested and found

to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable

protection against harmful interference in a

residential installation. This equipment generates,

uses and can radiate radio frequency energy

and, if not installed and used in accordance with

the instructions, may cause harmful interference

to radio communications. However, there is no

guarantee that interference will not occur in a

particular installation. If this equipment does

cause harmful interference to radio or television

reception, which can be determined by turning

the equipment o and on, the user is encouraged

to try to correct the interference by one or more of

the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the

equipment and receiver.

• Connect the equipment into an outlet on

a circuit dierent from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV

technician for help.

CAUTION: Changes or modications not expressly

approved by the party responsible for compliance

could void the user’s (or your) authority to operate

the equipment. Avoid storage in extreme heat

or cold. Avoid exposure to liquids, temperature

extremes and high humidity. The product’s

working temperature range is 0–45°C (32–113°F).

This device complies with FCC/IC radiation

exposure limits set forth for an uncontrolled

environment.

Canada Notice — IC ID: 5153A-

190653

This Class B digital apparatus complies with

Canadian ICES-003.

This device complies with RSS 210 of Industry

Canada. Operation is subject to the following two

conditions: (1) this device may not cause harmful

interference and (2) this device must accept any

interference,including interference that may cause

undesired operation of the device.

Canadian Class B Statement

This digital device does not exceed the Class

B limits for radio noise emissions from digital

apparatus as set out in the interference causing

equipment standard entitled“Digital Apparatus,”

ICES-003 of the Department of Communications.

CAN ICES-3 (B)/NMB-3(B)

Modication

Any changes or modications not expressly

approved by the grantee of this device could void

ENGLISH

Inhaltsverzeichnis

Sprachen:

Andere ROC Kopfhörer Handbücher

ROC

ROC Model II Bedienungsanleitung

Beliebte Kopfhörer Handbücher anderer Marken

Sony

Sony MDR-NC8 Bedienungsanleitung

AUSounds

AUSounds AU-Stream Bedienungsanleitung

ENERGY SISTEM

ENERGY SISTEM Style 7 Bedienungsanleitung

Philips

Philips SHE3622 Bedienungsanleitung

Insignia

Insignia NS-CAHBTSPORT Bedienungsanleitung

Movie Vision

Movie Vision HP-400 Bedienungsanleitung

MobiFren

MobiFren SM Pro Bedienungsanleitung

Motorola solutions

Motorola solutions PMLN8120 Bedienungsanleitung

Jaybird

Jaybird freedom Installationsanleitung

Sony

Sony MDR-ED12LP Bedienungsanleitung

HiFuture

HiFuture Tidy Buds Pro Bedienungsanleitung

Creative

Creative CB2530 Bedienungsanleitung

Renkforce

Renkforce RF FTVK-100 Bedienungsanleitung

Philips

Philips SHQ3000 Bedienungsanleitung

Sennheiser

Sennheiser 500371 Bedienungsanleitung

Califone

Califone 2924AV Bedienungsanleitung

Philips

Philips EARGEAR HE205 Series Bedienungsanleitung

Technics

Technics EAH-AZ80 Bedienungsanleitung