Rockford Fosgate POWER 150 Bedienungsanleitung

® ®

car audio

fanatics

for

mono Amplifiers

Operation & Installation

power

POWER 150 POWER 200

Dynamic Power Rating (IHF-202 Standard) - Measured at 14.4 Volts

Mono into a 4ΩLoad 110 Watts 150 Watts

Mono into a 2ΩLoad 190 Watts 260 Watts

Continuous Power Rating (Competition Standard) - Measured at 13.8 Battery Volts

RMS continuous power mono, driven into a 75 Watts 100 Watts

4Ωload from 20 to 20,000Hz with less than

0.05% Total Harmonic Distortion (THD)

RMS continuous power mono, driven into a 150 Watts 200 Watts

2Ωload from 20 to 20,000Hz, with less than

0.1% Total Harmonic Distortion (THD)

Signal-to-Noise Ratio >100dB A-weighted

Crossover Slope 12dB/octave Butterworth

Crossover Frequency variable from 50Hz to 210Hz

Dimensions 2.60" (6.60cm) H 2.60" (6.60cm) H

9.60" (24.38cm) W 9.60" (24.38cm) W

6.70" (17.01cm) L 7.70" (19.55cm) L

Frequency Response 20Hz to 20kHz ±0.5dB

Bandwidth 10Hz to 200kHz ±3dB

Damping Factor @ 4Ω(at output connector ) >200

Slew Rate 30 Volts/µs

IM Distortion (IHF) <0.05%

Source Unit Compatibility (+15dB gain overlap) 17V max. (low level in)

Input Sensitivity (+0dB gain overlap) Variable from 250mV to 4V (low level in)

Variable from 650mV to 11V (high level in)

Protection NOMAD - Internal analog-computer output protection

circuitry limits power in case of overload. Thermal

switch shuts down the amplifier in case of overheating.

Battery Fusing Rates (External to Amplifier) 15 amps 20 amps

Fuse Type ATC ATC

Equalization (45Hz Punch Bass) Variable from 0dB to +18dB @ 45Hz

Input Impedance 20k ohms

Specifications are subject to change without notice.

PECIFICATIONS

– i –

Dear Customer,

Congratulations on your purchase of the world's finest brand of car audio amplifiers.

AtRockfordFosgatewearefanaticsaboutmusicalreproductionatitsbest,andweare

pleasedyouchoseourproduct.Throughyearsofengineeringexpertise,handcraftsman-

ship and critical testing procedures, we have created a wide range of products that

reproduce music with all the clarity and richness you deserve.

For maximum performance we recommend you have your new Rockford Fosgate

product installed by an Authorized Rockford Fosgate Dealer, as we provide specialized

training through Rockford Technical Training Institute (RTTI). Please read your

warranty and retain your receipt and original carton for possible future use.

Greatproductandcompetent installationsareonlyapieceofthepuzzle whenitcomes

to your system. Make sure that your installer is using 100% authentic installation

accessories from Connecting Punch in your installation. Connecting Punch has

everything from RCA cables and speaker wire to Power line and battery connectors.

Insist on it! After all, your new system deserves nothing but the best.

To add the finishing touch to your new Rockford Fosgate image order your Rockford

wearables,which include everything from T-shirts and jackets tohats and sunglasses.

To get a free brochure on Rockford Fosgate products and Rockford accessories, in the

U.S.call602-967-3565orFAX602-967-8132.Forallothercountries,call+001-602-

967-3565 or FAX +001-602-967-8132.

If, after reading your manual, you still have questions regarding this product,

we recommend that you see your Rockford Fosgate dealer. If you need further

assistance, you can call us direct at 1-800-669-9899. Be sure to have your serial

number, model number and date of purchase available when you call.

PRACTICE SAFE SOUND™

CONTINUOUS EXPOSURE TO SOUND PRESSURE LEVELS OVER 100dB

MAY CAUSE PERMANENT HEARING LOSS.HIGH POWERED AUTOSOUND

SYSTEMS MAY PRODUCE SOUND PRESSURE LEVELS WELL OVER

130dB. USE COMMON SENSE AND PRACTICE SAFE SOUND.

The serial number can be found on the outside of the box. Please record it in

the space provided below as your permanent record. This will serve as

verificationofyourfactorywarrantyandmaybecomeusefulinrecoveringyour

amplifier if it is ever stolen.

Serial Number: ________________________________

Model Number:________________________________

– ii –

ABLE

ONTENTS

Specifications .............................................................................................. i

Introduction................................................................................................1

Amplifier Accessory Pack ............................................................................. 1

Feature Chart..............................................................................................2

Design Features .......................................................................................... 4

Installation Considerations ...........................................................................6

Mounting Location ...................................................................................... 7

Battery and Charging ..................................................................................8

Wiring the System.......................................................................................8

Using Passive Crossovers........................................................................... 10

Table of Component Values........................................................................ 11

Installation ...............................................................................................12

System Diagrams...................................................................................... 15

Troubleshooting........................................................................................ 18

Dynamic Power Measurements................................................................... 20

Warranty Information ................................................................................ 22

International Information............................................................................23

Sections marked

ADVANCED OPERATION

include in-depth

technical information

Sections marked

TROUBLESHOOTING

include recommendations for

curing installation problems

Sections marked

INSTALLATION

include “slam dunk”

wiring connections

® ®

TROUBLE-S

Welcometo Rockford Fosgate! This manual is designedto provide information

for the owner, salesperson and installer. For those of you who want quick

information on how to install this product, please turn to the

Installation

Section

of this manual or refer to the icons listed below. Other information can

be located by using the Table of Contents. We, at Rockford Fosgate, have

workedveryhardtomakesurealltheinformationinthismanualiscurrent.But,

asweareconstantlyfindingnewwaystoimproveourproduct,thisinformation

is subject to change without notice.

GETTING STARTED

NTRODUCTION

Rockford engineers designed the Power 150 and Power 200 amplifiers to

withstand the rugged automotive environment while delivering superior

sound quality in a flexible, reliable, and efficient package. TRANS•

ana

is a

lowvoltagecircuitinthepreampstageletsthemusicsoundcrystalclearand

very real, even when played at high volume levels. This is matched with

TOPAZ, a unique grounding circuit used to eliminate noise problems

associated with car audio systems and their installation. Flexibility is

accomplished with the use of a built-in variable crossover. The use of a

protection circuit called NOMAD, along with MOSFET and DSM (Discrete

SurfaceMount)technologiesimproveamplifierefficiency.Theresultofthese

components give the Power amplifier awesome sound quality in a “Bullet

Proof” package. Explanations of these technologies, most of which are

exclusively designed and patented by Rockford, are described in the

Technical Design Features.

– 1 –

MPLIFIER

CCESSORY

ACK

The accessory pack included with each amplifier contains the mounting

hardware necessary to secure the amp to the vehicle and to attach the end

caps to the amplifier.

Installation & Operation Manual

Punch Verification Certificate

(4) Amplifier mounting screws (#8 x 3/4" Phillips)

(4) Speaker/Power Connector Set Screws (3/32" Allen)

(4) Endbell Mounting Screws (9/64" Allen)

(1) Allen Wrench 9/64"

(1) Allen Wrench 3/32"

(1) High Level Input Harness (replacement part #CC-1992)

(1) ATC Inline Fuseholder

(1) ATC 15 Amp Fuse (Power 150)

(1) ATC 20 Amp Fuse (Power 200)

OWER

ONO

MPLIFIER

EATURE

HART

– 2 –

Power 150 Power 200

# of CHANNELS 11

RMS Power Mono (4Ω) 75x1 100x1

RMS Power Mono (2Ω) 150x1 200x1

Stable Into: 2Ω2Ω

CIRCUITRY1

TRANS•

ana

– circuit topology xx

TRANS•

nova

– patented circuit topology2--

Class-H – high efficiency topology --

MEHSA – heat dissipating technology -x

TOPAZ– patented noise eliminating circuitry3x

DSM – discrete surface mount xx

MOSFETs – power supply and output devices xx

NOMAD – protection circuit xx

FEATURES

Die Cast Heatsink4xx

Hi-Level Inputs x x

RCA Inputs x x

Balanced Inputs - -

Input Switches - -

Pass-Thru x x

Pwr/Spk Screw Terminals - -

Pwr/Spk Block Terminals x x

4 Gauge Pwr/Gnd - -

– 3 –

--INTERNAL USE ONLY--

Heatsink Type #1 #2

Power 150 Power 200

Fixed Punch Bass - -

(0dB/+6dB/+12dB @ 45Hz)

Variable Punch Bass x x

(0dB ~+18dB @ 45Hz)

Adjustable Crossover (80Hz fixed) - -

Variable Crossover (50Hz ~ 210Hz) LP/FULL5LP/FULL5

Crossover Slope (Butterworth) 12dB/octave 12dB/octave

Phase Warp (00~1800)--

GENERAL

B+ Fuse Size 15A ATC 20A ATC

Dimensions (H x W x L) 2.60" x 2.60" x

9.60" x 9.60" x

6.70" 7.70"

(6.60cm x (6.60cm x

24.38cm x 24.38cm x

17.01cm) 19.55cm)

1Additional information on features, specifications and system designs can be

found at: www.rockfordfosgate.com

2Trans•nova is patented under U.S. Patent No. 4,467,288

3TOPAZ is patented under U.S. Patent No. 5,751,823

4Diecast Heatsink patent pending

5HP = 12dB/octave High-Pass / LP = 12dB/octave Low-Pass / FULL = Full Range

ESIGN

EATURES

1. Cast Aluminum Heatsink – The cast aluminum heatsink of the Punch

amplifier dissipates heat generated by the amplifier's circuitry. The

inherentadvantage of casting provides a 30% improvement of cooling

over conventional extrusion heatsink designs.

2. Speaker Terminals – The heavy duty, gold-plated terminal block

connectors (+ and –) will accept wire sizes from 8 AWG to 18 AWG.

These gold-plated connectors are immune to corrosion that can cause

signal deterioration.

3. Power Terminals – The power and ground connectors on the Punch

amplifier are gold-plated and will accommodate up to 8 AWG wire

maximizing the input current capability of the amplifier.

4. REM Terminal – This spade terminal is used to remotely turn-on and

turn-off the amplifier when +12V DC is applied.

5. RCA Input Jacks – The industry standard RCA jacks provide an easy

connectionforsignallevelinput.Theyaregold-platedtoresistthesignal

degradation caused by corrosion.

6. High Level Inputs – The high level inputs use a detachable connector

terminatedwith20AWGleads.Theseinputsshouldbeusedifthesource

unit has only speaker line (high level) outputs.

7. Gain Control – The input gain control is preset to match the output of

most source units. It can be adjusted to match output levels from a

variety of source units.

– 4 –

Punch 150

Punch 200

911 476 532 1

810

L+

L–

R+

R–

110

210 Hz

145

190

Crossover

Frequency

Punch

Bass

18dB 0dB

REM – + B+ GND

High

Level

Input

LED

Pass-Thru

Input

L R

Gain Crossover

L R

LP Full

– 5 –

8. RCAPass-ThruJacks–ThePass-Thruprovidesaconvenientsourcefor

daisy-chaining an additional amplifier without running an extra set of

RCA cables from the front of the vehicle to the rear amplifier location.

9. Punch Bass – The Punch Bass control helps correct for acoustical

deficiencies in the listening environment. The Punch Bass allows a

narrow band adjustment at 45Hz to help reproduce full range sound

without excessive boost.

10. Variable Crossover – The amplifiers have a built-in 12dB/octave

Butterworth filter with a crossover point variable from 50Hz to 210Hz.

The crossover can be set to Low-Pass (LP) or it can be bypassed by

setting it to Full Range (FULL).

11. LED Power Indicator – TheLED illuminates when the unit is turned on.

NSTALLATION

ONSIDERATIONS

The following is a list of tools you will need for installing the amplifier:

Allen wrenches 9/64" & 3/32" (included) Voltmeter

Wire strippers Battery post wrench

Electric hand drill w/assorted bits Wire cutters

17' (5m) Red Power Wire Assorted connectors

12' (4m) Remote Turn-On Wire Wire crimpers

1.5' (45cm) Black Grounding Wire

– 6 –

Thissectionfocuses on some of the vehicle considerations for installing your

new Punch amplifier. Checking your battery and present sound system, as

well as pre-planning your system layout and best wiring routes, will save

installationtime. Whendecidinghowtolayoutyournewsystem,besurethat

each component will be easily accessible for making adjustments.

Before beginning any installation, be sure to follow these simple rules:

1. Besuretocarefullyreadandunderstandtheinstructionsbeforeattempt-

ing to install the amplifier.

2. For safety, disconnect the negative lead from the battery prior to

beginning the installation.

3. Foreasierassembly,wesuggestyourunallwirespriortomountingyour

amplifier in place.

4. Route all of the RCA cables close together and away from any high

current wires.

5. Use high quality connectors for a reliable installation and to minimize

signal or power loss.

6. Think before you drill! Be careful not to cut or drill into gas tanks, fuel

lines, brake or hydraulic lines, vacuum lines or electrical wiring when

working on any vehicle.

7. Never run wires underneath the vehicle. Running the wires inside the

vehicle provides the best protection.

8. Avoid running wires over or through sharp edges. Use rubber or plastic

grommets to protect any wires routed through metal, especially the

firewall.

9. ALWAYS protect the battery and electrical system from damage with

proper fusing. Install a fuseholder and appropriate fuse on the +12V

power wire within 18” (46 cm) of the battery terminal.

10. When grounding to the chassis of the vehicle, scrape all paint from the

metal to ensure a good, clean ground connection. Grounding connec-

tions should be as short as possible and always be connected to metal

that is welded to the main body, or chassis, of the vehicle.

Andere Handbücher für POWER 150

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Rockford Fosgate Verstärker Handbücher

Rockford Fosgate

Rockford Fosgate PRIME R2-200X2 Leitfaden

Rockford Fosgate

Rockford Fosgate Punch P500-2 Leitfaden

Rockford Fosgate

Rockford Fosgate PM100X1 Technisches Datenblatt

Rockford Fosgate

Rockford Fosgate Punch RF2002 Original Betriebsanleitung

Rockford Fosgate

Rockford Fosgate Power T1500-1bd Leitfaden

Rockford Fosgate

Rockford Fosgate PUNCH Pro Series Leitfaden

Rockford Fosgate

Rockford Fosgate Punch 100 Leitfaden

Rockford Fosgate

Rockford Fosgate T2500-1bd CP Leitfaden

Rockford Fosgate

Rockford Fosgate Prime R600-5 Leitfaden

Rockford Fosgate

Rockford Fosgate POWER 150 Bedienungsanleitung

Rockford Fosgate

Rockford Fosgate 5.3x Betriebsanleitung

Rockford Fosgate

Rockford Fosgate Power BD1500.1 Bedienungsanleitung

Rockford Fosgate

Rockford Fosgate 250 2-Channel, 360 2-Channel, Betriebsanleitung

Rockford Fosgate

Rockford Fosgate Punch P200.2 Montageanleitung

Rockford Fosgate

Rockford Fosgate Punch 250.2 Bedienungsanleitung

Rockford Fosgate

Rockford Fosgate Punch X150.1 Leitfaden

Rockford Fosgate

Rockford Fosgate punch 160X4 Bedienungsanleitung

Rockford Fosgate

Rockford Fosgate 250 sERIES Leitfaden

Rockford Fosgate

Rockford Fosgate Marine M400-4D Original Betriebsanleitung

Rockford Fosgate

Rockford Fosgate PUNCH 40.2 Anleitung zur Verwendung

Rockford Fosgate

Rockford Fosgate R400-4D Leitfaden

Rockford Fosgate

Rockford Fosgate PUNCH 200 Bedienungsanleitung

Rockford Fosgate

Rockford Fosgate punch 40X2 Bedienungsanleitung

Rockford Fosgate

Rockford Fosgate PUNCH 45.2 Installations- und Betriebsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung