Rockford Fosgate Punch 120 Leitfaden

® ®

car audio

fanatics

for

punch

2-CHANNEL AMPLIFIER

INSTALLATION & OPERATION

2 - c h a n n e l

PUNCH 120 PUNCH 160 PUNCH 250 PUNCH 360 PUNCH 500 PUNCH 800

Dynamic Power Rating

(IHF-202 Standard) - Measured at 14.4 Volts

Mono into a 4ΩLoad

200 Watts x 1 236 Watts x 1 320 Watts x 1 450 Watts x 1 710 Watts x 1 960 Watts x

Per channel into a 2ΩLoad

94 Watts x 2 113 Watts x 2 160 Watts x 2 210 Watts x 2 330 Watts x 2 480 Watts x 2

Per channel into a 4ΩLoad

64 Watts x 2 77 Watts x 2 100 Watts x 2 140 Watts x 2 210 Watts x 2 240 Watts x 2

Continuous Power Rating

(Competition Standard) - Measured at 13.8 Battery Volts

RMS continuous power per channel,

30 Watts x 2 40 Watts x 2 62.5 Watts x 2 90 Watts x 2 125 Watts x 2 200 Watts x 2

both channels driven into a 4Ωload

from 20 to 20,000 Hz with less than

0.05% Total Harmonic Distortion (THD)

RMS continuous power per channel,

60 Watts x 2 80 Watts x 2 125 Watts x 2 180 Watts x 2 250 Watts x 2 400 Watts x 2

both channels driven into a 2Ωload

from 20 to 20,000 Hz, with less than

0.1% Total Harmonic Distortion (THD)

RMS continuous power mono into a

120 Watts x 1 160 Watts x 1 250 Watts x 1 360 Watts x 1 500 Watts x 1 800 Watts x 1

4Ωload from 20 to 20,000 Hz, with

less than 0.1% Total Harmonic Distortion (THD)

Signal-to-Noise Ratio (A-weighted) > 100dB > 100dB > 100dB > 100dB > 100dB > 100dB

Crossover Slope (Butterworth) 12dB/octave 12dB/octave 12dB/octave 12dB/octave 12dB/octave 12dB/octave

Crossover Frequency

80Hz 80Hz 50Hz – 210Hz 50Hz – 210Hz 50Hz – 210Hz 50Hz – 210Hz

Specifications are subject to change without notice.

– i –

PECIFICATIONS

PUNCH 120 PUNCH 160 PUNCH 250 PUNCH 360 PUNCH 500 PUNCH 800

Dimensions (end caps installed)

2.62" (6.65cm) H 2.62" (6.65cm) H 2.62" (6.65cm) H 2.62" (6.65cm) H 2.62" (6.65cm) H 2.62" (6.65cm) H

9.60" (24.38cm) W 9.60" (24.38cm) W 9.60" (24.38cm) W 9.60" (24.38cm) W 9.60" (24.38cm) W 9.60" (24.38cm) W

10.27" (26.08cm) L 10.27" (26.08cm) L 11.27" (28.62cm) L 12.27" (31.16cm) L 13.27" (33.70cm) L 18.27" (46.40cm) L

Heatsink Tpye (internal use only) #1 #1 #2 #3 #4 #6

Frequency Response (±0.5dB) 20Hz - 20kHz 20Hz - 20kHz 20Hz - 20kHz 20Hz - 20kHz 20Hz - 20kHz 20Hz - 20kHz

Bandwidth (±3dB) 10Hz - 200kHz 10Hz - 200kHz 10Hz - 200kHz 10Hz - 200kHz 10Hz - 200kHz 10Hz - 200kHz

Damping Factor @ 4Ω(at output connector) >200 >200 >200 >200 >200 >200

Slew Rate 30 Volts µs 30 Volts µs 30 Volts µs 30 Volts µs 30 Volts µs 30 Volts µs

IM Distortion (IHF) <0.05% <0.05% <0.05% <0.05% <0.05% <0.05%

Source Unit Compatibility (+15dB gain overlap)

17V max. (RCA) 17V max. (RCA) 17V max. (RCA) 17V max. (RCA) 17V max. (RCA) 17V max. (RCA)

Input Sensitivity (+0dB gain overlap) 250mV~4V (RCA) 250mV~4V (RCA) 250mV~4V (RCA) 250mV~4V (RCA) 250mV~4V (RCA) 250mV~4V (RCA)

650mV~11V (hi-level) 650mV~11V (hi-level) 650mV~11V (hi-level) 650mV~11V (hi-level) 650mV~11V (hi-level) 650mV~11V (hi-level)

Protection NOMAD - Internal analog-computer output protection circuitry limits power in case of

overload. Thermal switch shuts down the amplifier in case of overheating.

Battery Fuse Rating (External to Amplifier) 20A 20A 30A 40A 50A 60A*

Fuse Type ATC ATC ATC ATC AGU AGU

Equalization (45Hz Punch Bass) Adjustable Variable Variable Variable Variable Variable

(0,+6,+12dB) (0 to +18dB) (0 to +18dB) (0 to +18dB) (0 to +18dB) (0 to +18dB)

Input Impedance 20k ohms 20k ohms 20k ohms 20k ohms 20k ohms 20k ohms

*recommended fuse not supplied

Specifications are subject to change without notice.

PECIFICATIONS

– ii –

Dear Customer,

Congratulations on your purchase of the world's finest brand of car audio amplifiers.

At Rockford Fosgate we are fanatics about musical reproduction at its best, and we are

pleasedyouchoseourproduct.Throughyearsofengineeringexpertise,handcraftsman-

ship and critical testing procedures, we have created a wide range of products that

reproduce music with all the clarity and richness you deserve.

For maximum performance we recommend you have your new Rockford Fosgate

product installed by an Authorized Rockford Fosgate Dealer, as we provide specialized

training through Rockford Technical Training Institute (RTTI). Please read your

warranty and retain your receipt and original carton for possible future use.

Great product and competent installations are only a piece of the puzzle when it comes

to your system. Make sure that your installer is using 100% authentic installation

accessories from Connecting Punch in your installation. Connecting Punch has

everything from RCA cables and speaker wire to Power line and battery connectors.

Insist on it! After all, your new system deserves nothing but the best.

To add the finishing touch to your new Rockford Fosgate image order your Rockford

wearables, which include everything from T-shirts and jackets to hats and sunglasses.

To get a free brochure on Rockford Fosgate products and Rockford accessories, in the

U.S. call 480-967-3565 or FAX 480-967-8132. For all other countries, call +001-480-

967-3565 or FAX +001-480-967-8132.

If, after reading your manual, you still have questions regarding this product,

we recommend that you see your Rockford Fosgate dealer. If you need further

assistance, you can call us direct at 1-800-669-9899. Be sure to have your serial

number, model number and date of purchase available when you call.

PRACTICE SAFE SOUND™

CONTINUOUS EXPOSURE TO SOUND PRESSURE LEVELS OVER 100dB

MAY CAUSE PERMANENT HEARING LOSS. HIGH POWERED AUTOSOUND

SYSTEMS MAY PRODUCE SOUND PRESSURE LEVELS WELL OVER

130dB. USE COMMON SENSE AND PRACTICE SAFE SOUND.

The serial number can be found on the outside of the box. Please record it in

the space provided below as your permanent record. This will serve as

verification of your factory warranty and may become useful in recovering your

amplifier if it is ever stolen.

Serial Number: ________________________________

Model Number: ________________________________

ABLE

ONTENTS

Specifications .............................................................................................. i

Introduction................................................................................................ 1

Punch Amplifier Accessory Pack ................................................................... 1

2-Channel Feature Chart .............................................................................. 2

Design Features .......................................................................................... 3

Installation Considerations ........................................................................... 6

Mounting Location ...................................................................................... 7

Battery and Charging .................................................................................. 8

Wiring the System ....................................................................................... 8

Using Passive Crossovers ........................................................................... 10

Table of Component Values........................................................................ 11

Installation ............................................................................................... 12

Operation................................................................................................. 19

System Diagrams...................................................................................... 20

Troubleshooting ........................................................................................ 23

Dynamic Power Measurements................................................................... 25

Warranty Information ................................................................................ 27

International Information ............................................................................ 28

Sections marked

ADVANCED OPERATION

include in-depth

technical information

Sections marked

TROUBLESHOOTING

include recommendations for

curing installation problems

Sections marked

INSTALLATION

include “slam dunk”

wiring connections

Welcome to Rockford Fosgate! This manual is designed to provide information

for the owner, salesperson and installer. For those of you who want quick

information on how to install this product, please turn to the

Installation

Section

of this manual or refer to the icons listed below. Other information can

be located by using the Table of Contents. We, at Rockford Fosgate, have

worked very hard to make sure all the information in this manual is current. But,

as we are constantly finding new ways to improve our product, this information

is subject to change without notice.

GETTING STARTED

+ -

TROUBLE-S

NTRODUCTION

Rockford engineers designed the Punch 2-channel amplifiers to withstand

the rugged automotive environment while delivering superior sound quality

in a flexible, reliable, and efficient package. TRANS•ANA is a low voltage

circuit in the preamp stage of all Punch amplifiers that lets the music sound

crystal clear and very real, even when played at high volume levels. This is

matched with TOPAZ, a unique grounding circuit used to eliminate noise

problems associated with car audio systems and their installation. Flexibility

is accomplished with the use of a built-in crossover. The use of a protection

circuit called NOMAD, along with MOSFET and DSM (Discrete Surface

Mount) technologies improve amplifier efficiency. The result of these

components give the Punch amplifier awesome sound quality in a “Bullet

Proof” package. An explanation of these technologies, most of which are

exclusively designed and patented by Rockford, are described in the

Technical Design Features.

– 1 –

UNCH

MPLIFIER

CCESSORY

ACK

The accessory pack shipped with the Punch 2-channel amplifiers includes

the mounting hardware necessary to secure the amp to the vehicle and to

attach the end caps to the amplifier.

Installation & Operation Manual

Punch Verification Certificate

(4) Amplifier mounting screws (#8 x 3/4" Phillips)

(1) ATC Inline Fuseholder (Punch 120, 160, 250, 360)

(1) AGU Inline Fuseholder (Punch 500)

(1) ATC 15 Amp Fuse (Punch 120)

(1) ATC 20 Amp Fuse (Punch 160)

(1) ATC 30 Amp Fuse (Punch 250)

(1) ATC 40 Amp Fuse (Punch 360)

(1) AGU 50 Amp Fuse (Punch 500)

Note:

Refer to the Specification section of this manual for recommended

Punch 800 fuse size.

– 2 –

UNCH

2-C

HANNEL

MPLIFIER

EATURE

HART

PUNCH AMPLIFIER MODEL

120 160 250 360 500 800

# of CHANNELS 22 2 222

Stable into: (stereo/bridged) 2Ω/4Ω2Ω/4Ω2Ω/4Ω2Ω/4Ω2Ω/4Ω2Ω/4Ω

CIRCUITRY

TRANS•

ana

– circuit topology xx x xxx

TRANS•

nova

– patented circuit topology

–– – –––

Class-G – high efficiency topology –– – –––

MEHSA – heat dissipating technology xx x xxx

TOPAZ

– patented noise eliminating circuitry

xx x xxx

DSM – discrete surface mount xx x xxx

MOSFETs – power supply & output devices xx x xxx

NOMAD – protection circuit xx x xxx

FEATURES

Die Cast Heatsink

xx x xxx

Hi-Level Inputs – for factory radios xx x xxx

RCA Inputs – for aftermarket radios xx x xxx

Balanced Inputs – – – – – –

Input Switches – eliminates “Y” adaptors –– – –––

Pass-Thru – feeds signal to aux. amp –– – –––

Pwr/Spk Screw Terminals x x – – – –

Pwr/Spk Block Terminals – – x x x x

4 Gauge Pwr/Gnd – – – – – –

Adjustable Punch Bass

(0dB/+6dB/+12dB @ 45Hz)

x– – –––

Variable Punch Bass (0dB ~+18dB @ 45Hz) –x x xxx

Adjustable Xover (120Hz HP / 80Hz LP)

HP/FULL/LP

––––

Variable Xover (50Hz ~ 210Hz) ––HP/FULL/LP

HP/FULL/LP

Crossover Slope (Butterworth) 12dB 12dB 12dB 12dB 12dB 12dB

Phase Warp (0

~ 180

)-- - ---

1Additional information on features, specifications and system designs can be found at: www.rockfordfosgate.com

2Trans•nova is patented under "U.S. Patent No. 4,467,288"

3TOPAZ is patented under "U.S. Patent No. 5,751,823"

4Diecast Heatsink is patented under "U.S. Patent No. D401,225"

5HP = 12dB/octave High-Pass / LP = 12dB/octave Low-Pass / FULL = Full Range

6Recommended fuse not supplied with amplifier

– 3 –

ESIGN

EATURES

L+

L–

R+

R–

+ – B+ GND

Left Right

+ –

120HP-Full-80LP

Crossover

REM

High

Level

Input

LED

Left Input Right Input Gain

+12dB

+6dB

0dB

Punch

Bass

7 5 3

REM

+ –

B+ GND

High

Level

Input

LED

Left Input Right Input Gain

Left Right

Punch

Bass

+ –

120HP-Full-80LP

Crossover

L+

L–

R+

R–

L+

L–

R+

R–

Punch 120

2-channel

Punch 160

2-channel

– 4 –

110

210 Hz

145

190

Speaker

+ L –

L+

L–

R+

R–

932

7 8 646 5

REM B+ GND

LED

HP–Full–LP

Crossover

Right

Gain

Right

Input

Left

Input

Left

Gain

Crossover

Frequency

Punch

Bass

High

Level

Input Speaker

+ R –

HP–Full–LP

Crossover

High

Level

Input

Right

Gain

Right

Input

Left

Input

Left

Gain

Crossover

Frequency

Punch

Bass

Speaker

+ L –Speaker

+ R –

L+

L–

R+

R–

110

210 Hz

145

190

REM

B+ GND

LED

274521

Punch 800

2-channel

Punch 250

2-channel

Punch 360

2-channel

Punch 500

2-channel

– 5 –

1. Cast Aluminum Heatsink – The cast aluminum heatsink of the Punch

amplifier dissipates heat generated by the amplifier's circuitry. The

inherent advantage of casting provides a 30% improvement of cooling

over conventional extrusion heatsink designs.

2. Speaker/Power Terminals –These gold-plated connectors are used for

the connection of speaker and power wire and are immune to corrosion

that can cause signal degradation. The Punch 120 and Punch 160

utilize a barrier strip that will accept #10 spade lugs or bare speaker and

power wires sized from 10-18 AWG. The Punch 250, Punch 360,

Punch 500, and Punch 800 utilize heavy duty terminal block connec-

tors that will accept bare wires size from 8-18AWG.

3. REM Terminal – This spade terminal is used to remotely turn-on and

turn-off the amplifier when +12V DC is applied.

4. RCA Input Jacks – The industry standard RCA jack provides an easy

connection for signal level input. They are gold-plated to resist the signal

degradation caused by corrosion.

5. High Level Inputs – The high level inputs use a detachable connector

terminated with 20 AWG leads. These inputs should be used if the source

unit has only speaker line (high level) outputs and not RCA outputs.

6. Gain Control – The input gain control is preset to match the output of

most source units. They can be adjusted to match output levels from a

variety of source units.

7. Punch Bass – The Punch Bass helps correct for acoustical deficiencies

in the listening environment. The Punch Bass allows a narrow band

adjustmentat45Hzto help reproducefullrangesound without excessive

boost. The Punch 120 utilizes a switch that is adjustable at 0dB/+6dB/

+12dB increments. The Punch 160,Punch 250, Punch 360, Punch

500, and Punch 800 utilize a control that is variable from 0dB to

+18dB.

8. InternalCrossover– Theinternal crossover isused to delegatea specific

range of frequencies to the speaker system for optimum performance.

The crossover can perform three functions: High-Pass (HP), Low-Pass

(LP), or Full Range (FULL). The Punch 120 and Punch 160 utilize a

12dB/octave Butterworth crossover fixed at 120Hz HP and 80Hz LP.

The Punch 250, Punch 360, Punch 500, and Punch 800 utilize a

12dB/octave Butterworth crossover variable from 50Hz to 210Hz.

9. LED Power Indicator – The LED illuminates when the unit is turned on.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Rockford Fosgate Auto-Verstärker Handbücher

Rockford Fosgate

Rockford Fosgate Punch200 trans ana 4-channel Leitfaden

Rockford Fosgate

Rockford Fosgate PBR500X1 Bedienungsanleitung

Rockford Fosgate

Rockford Fosgate Prime R600-5 Betriebsanleitung

Rockford Fosgate

Rockford Fosgate 2300 Bedienungsanleitung

Rockford Fosgate

Rockford Fosgate Punch P200.2 Betriebsanleitung

Rockford Fosgate

Rockford Fosgate Punch P300-1 Betriebsanleitung

Rockford Fosgate

Rockford Fosgate Power T15kW Bedienungsanleitung

Rockford Fosgate

Rockford Fosgate Power 1050S Betriebsanleitung

Rockford Fosgate

Rockford Fosgate Power 351M Betriebsanleitung

Rockford Fosgate

Rockford Fosgate Marine M400-4D Original Betriebsanleitung

Rockford Fosgate

Rockford Fosgate Power Elite T3002 Bedienungsanleitung

Rockford Fosgate

Rockford Fosgate Punch P1000-1bd Betriebsanleitung

Rockford Fosgate

Rockford Fosgate Pro Series bd1001P Betriebsanleitung

Rockford Fosgate

Rockford Fosgate Punch 45 Bedienungsanleitung

Rockford Fosgate

Rockford Fosgate X1 Bedienungsanleitung

Rockford Fosgate

Rockford Fosgate Punch 100.2 Leitfaden

Rockford Fosgate

Rockford Fosgate Punch P4004 Betriebsanleitung

Rockford Fosgate

Rockford Fosgate Punch 150 Bedienungsanleitung

Rockford Fosgate

Rockford Fosgate Prime R150-2 Bedienungsanleitung

Rockford Fosgate

Rockford Fosgate Punch PBR300X1 Leitfaden

Rockford Fosgate

Rockford Fosgate Punch P200.2 Bedienungsanleitung

Rockford Fosgate

Rockford Fosgate Punch P450.4 Bedienungsanleitung

Rockford Fosgate

Rockford Fosgate Power 1001bd Betriebsanleitung

Rockford Fosgate

Rockford Fosgate P1200.2 Punch Leitfaden

Beliebte Auto-Verstärker Handbücher anderer Marken

Cyfre

Cyfre CHACDMA-819 Bedienungsanleitung

MTX

MTX Thunder Marine TM904 Bedienungsanleitung

MTX

MTX Thunder TA Super TA92001 Bedienungsanleitung

Lanier

Lanier 480-0239 Bedienungs- und Wartungsanleitung

Kenwood

Kenwood KAC-642 Bedienungsanleitung

Pioneer

Pioneer GM-D8500M Bedienungsanleitung

Jensen

Jensen XA4150 Bedienungsanleitung

Sony

Sony XM-405EQX Marketing Specifications Bedienungsanleitung

Audiopipe

Audiopipe AQX-660.2 Bedienungsanleitung

Clarion

Clarion APA2001 APA2001 APA2001 Kurzanleitung

Sony

Sony XM-7547 Bedienungsanleitung

Alpine

Alpine PDX11000 - Amplifier Bedienungsanleitung

Steg

Steg Qx Mos 105.4x Bedienungsanleitung

JL Audio

JL Audio HD900/5 Bedienungsanleitung

Memphis

Memphis 16-MC5.700 Bedienungsanleitung

Audiopipe

Audiopipe APSM-1150 Bedienungsanleitung

Boss Audio Systems

Boss Audio Systems Riot GT1000M Bedienungsanleitung

Kenwood

Kenwood KAC-PS811D Bedienungsanleitung

Rockford Fosgate punch 120 Leitfaden

Beliebte Auto-Verstärker Handbücher anderer Marken