6
Installation
Contents
1 -
BLACK
(Speaker Negative, 18
AWG}
2 -
YELLOW
(12V + Input, 22
AWG)
3 -
RED
(Speaker
Positive,
18
AWG}
4 -
GREEN
(Ground Input, 22
AWG}
5 -
RED
(Ground Input, 22
AWG}
6 -
BLUE
(Ground Input, 22
AWG)
Included with
speakers
Connector is DEUTSCH"'/Amphenol style
DT0G-4S
il/us.-4.3
•
(1)
PairMoto
Can
Speakers •
(2)
SpeakerHarnesses
14"
(355mm)
15"
(380mm) illus. 4.4
•
(1)
Pair Universal Clamps •
(1)
PairSportGrills
(Installed on
Ml)
Mounting
•
(4)
Grommets
•
(4)
Safety Inserts forScrew
Clamp
•
(2)
1" to
1.
6"
RubberClamp
Inserts andStainless
Hardware
•
(2)
1.
6" to 2"Rubber Clamp
Inserts andStainless
Hardware
Installation
Considerations
•
(1)
PairSportGrills
(Installed on
M2,
not
available on
Ml)
•
(1)
Allen BitForSpeaker
Removal For Rotation
•
(1)
Safety
Torx
Wrench
Before beginning anyinstallation, follow these simple rules:
1.
Be
sure to carefully read and understand the instructions
before attempting to install these speakers.
2.
For safety, disconnect the negative lead from the battery
prior
to beginning the installation.
3.
For easier assembly,
we
suggestyou run
all
wires
prior
to
mounting
your
speakers in place.
4.
Use
high quality connectors for a reliable installation and
to
minimizesignal
or
power
loss.
5.
Think before you drill!
Be
careful
not
to
cut
or
drill into gas
tanks, fuel lines, brake
or
hydraulic lines, vacuum lines
or
electricalwiring when working on anyvehicle.
If
installation
in
a boat, take care
not
to
cut
or
drill through the main hull.
6.
Never run wires underneath the vehicle. Running the wires
inside the vehicle
or
hullarea provides the bestprotection.
7.
Avoid running wires over
or
through sharp edges.
Use
rubber
or
plastic grommets to protect any wires routed
through metal, especiallythe firewall.
1.
Determine where the speakers
will
be
mounted.
Be
sure
that
the mounting location has sufficient clearance in
all
direction for the speakerto swivel; conduct a full rotation to
ensure there
is
not
obstruction.
2.
Mark the location where the wiring
will
come
out
near
where the Moto can
will
be
mounted. Drill a 7/16" hole
in
the location you marked for
your
wire exit.
The
wiring
will
connect to the rear
of
the can i/lus.-4.2.
3.
Insert the supplied grommet and feed the wire harness
through.
Be
sure to observe proper
polarity
when
connecting the wires.
The
speaker harness's negative wire
is
the
BLACK
lBAWG wire
and
the Positive
is
the
RED
lBAWG
wire
in
the 6pin connectorillus.-4.3.
4.
Remove the plastic cover over the safety torx
bolt
to
allow
access
to
loosen/tighten the wake can.
Do
this
to
adjust
the angle
of
the wake can, then tighten the safety torx
bolt
to make sure
it
does
not
move. Replace plastic cover over
safety torx
bolt
illus.-3.3.
5. Rotate the medalion on the rear
of
the wake can to looklike
the image in illus.-3.2.
This
can
be
turned left
or
right
to align
the medalion.
You
will
hear/feel a clicking when you rotate
it.
6.
If
you need to rotate the speaker, remove the
(6)
screws
holding th speaker and
grill
on.
Pull the speaker slightly
towards you and rotate
it
until
it
looks like illus.-1.1.
Use
the
predrilledholes to reinstall the speakerillus.-3.1.
