Rockler JIG IT 50713 Bedienungsanleitung

JIG IT®Undermount

Drilling Guide Instructions

Before attempting to install the locking devices, make

sure that the dimensions of your drawer box meet the

specifications in the instructions that came with your

Blum Tandem Drawer Slides. Also, as specified in the

instructions, cut notches in the back of the drawer box, at

the bottom, to accommodate the slides. Try to make the

notches as flush to the drawer bottom and square to the

sides as possible.

Set Depth Collars on Drill Bits

1. Slide the smaller depth collar on the 2.5mm drill bit and

insert the bit in the 2.5mm depth guide in the rounded

foot of the Drill Guide.

2. Allow the bit to bottom out in the hole and the stop

collar to rest on the Drill Guide. Secure the depth collar

by tightening the set screw with the included hex

wrench. Fig. 1.

3. Repeat Steps 1 and 2 for the 6mm bit, using the 6mm

depth guide in the Drill Guide. Fig. 1

Angled guide holes

for locking devices

Stop collar

depth guides

Pin guide holes

6mm drill bit

and stop collar

Hex wrench

2.5mm drill bits

with stop collar

2Distributed by Rockler Companies, Inc.

50713

Rev 10/15

Fig. 2

Fig. 3

Drill for the Locking Devices

1. With the drawer box upside down on a stable work

surface, position the Drilling Guide on the drawer

bottom in one of the front corners. Make sure the flat

foot is against the drawer side and the arrow points

to the side.

2. With the 2.5mm bit chucked in a handheld drill, hold

the Drill Guide in place and use the guide holes to drill

the angled holes for mounting the slide bracket. Fig. 2.

3. Flip the Drill Guide side-to-side and repeat Steps 1

and 2 in the other front bottom corner of the

drawer box.

Drill for the Slides’ Rear Pins

1. With the drawer box still upside down, place the Drill

Guide in one of the notches and against the drawer side.

Make sure the shoulder on the rounded foot of the

guide rests squarely on the bottom of the notch.

2. With the 6mm bit chucked in a handheld drill, hold the

Drill Guide in place and use the guide hole closest to

the drawer side to bore the hole for the rear pin

on the slide. Fig. 3.

3. Reposition the Drill Guide in the other notch and

repeat Steps 1 and 2, using the other guide hole in

the Drill Guide.

Check Rockler.com for updates. If you have further questions, please

contact our Technical Support Department at 1-800-260-9663

or support@rockler.com

Locking device

Inhaltsverzeichnis

Andere Rockler Werkzeuge Handbücher

Rockler

Rockler Dust RIGHT Bedienungsanleitung

Rockler

Rockler 43450 Betriebsanleitung

Rockler

Rockler Trim Router Table Bedienungsanleitung

Rockler

Rockler Miter-Tight Picture Frame Clamp Bedienungsanleitung

Rockler

Rockler Interlock Signmaker's Script Font Template Bedienungsanleitung

Rockler

Rockler 311373 Bedienungsanleitung

Rockler

Rockler Indexing Dado Bedienungsanleitung

Rockler

Rockler 57302 Bedienungsanleitung

Rockler

Rockler 57484 Bedienungsanleitung

Rockler

Rockler 52149 Bedienungsanleitung

Rockler

Rockler 68547 Bedienungsanleitung

Rockler

Rockler 22818 Bedienungsanleitung

Rockler

Rockler 55391 Bedienungsanleitung

Rockler

Rockler HPL Installationsanleitung

Rockler

Rockler ProFence 47905 Bedienungsanleitung

Rockler

Rockler 45968 Betriebsanleitung

Rockler

Rockler 56372 Bedienungsanleitung

Rockler

Rockler 55512 Bedienungsanleitung

Rockler

Rockler 59133 Bedienungsanleitung

Rockler

Rockler 52149 Bedienungsanleitung

Rockler

Rockler JIG IT Bedienungsanleitung

Rockler

Rockler Interlock Signmaker’s Templates State Park Bedienungsanleitung

Rockler

Rockler 37375 Bedienungsanleitung

Rockler

Rockler 63779 Bedienungsanleitung

Beliebte Werkzeuge Handbücher anderer Marken

Martor

Martor SECUNORM 175 Bedienungsanleitung

ERKCO

ERKCO 1000 Bedienungsanleitung

jbc

jbc N4473 Bedienungsanleitung

FEINMETALL

FEINMETALL FZWZ-SET-001 Bedienungsanleitung

Worx Professional

Worx Professional Sonicrafter WU676 Bedienungsanleitung

Gage Bilt

Gage Bilt GB713SH Bedienungsanleitung

Hilti

Hilti DX 9-ENP Bedienungsanleitung

norbar

norbar NORTRONIC 34399 Bedienungsanleitung

BGS technic

BGS technic 8578 Bedienungsanleitung

Makita

Makita DHR241 Bedienungsanleitung

Motor Guard

Motor Guard JMB-1250 Bedienungsanleitung

Power Adhesives

Power Adhesives 805-12 Bedienungsanleitung

Clemco

Clemco 24189 Bedienungsanleitung

VVG

VVG VNG 903 Series Bedienungsanleitung

Hilti

Hilti FX 3-A Bedienungsanleitung

Grizzly

Grizzly H6472 Bedienungsanleitung

axing

axing BWZ 5-02 Bedienungsanleitung

Dh-Robotics

Dh-Robotics RGI-100 Anleitung zur Verwendung