Rockwell Automation ArmorBlock MaXum 1792D-CB23 Bedienungsanleitung

Publication 1792D-IN054B-EN-P - April 2003

Installation Instructions

ArmorBlock MaXum Robot I/O Cable Base

and Kempf Box Plate

(Cat. No. 1792D-CB23 and -KPLT)

The 23mm ArmorBlock MaXum Robot Ι/Ο Cable Base mates with 4

or 8 point modules, depending on your installation requirements, and

optionally the Kempf box plate. No modification is required. Modules

are interchangeable whether flat or round media cable bases are

used. This interchangeability provides plug and play block upgrade

capability and easy field replacement. The completely assembled

ArmorBlock module and base requires no enclosure.

CB23 KPLT

43333

43338

2ArmorBlock MaXum Robot I/O Cable Base and Kempf Box Plate

Publication 1792D-IN054B-EN-P - April 2003

These instructions describe the installation of the cable base. The

catalog numbers for the cable base and Kempf box are:

•1792D-CB23 (for 23mm trunk or drop cable installation)

•1792D-KPLT (to mount the cable base on a Kempf box)

Important User Information

Because of the variety of uses for the products described in this

publication, those responsible for the application and use of these

products must satisfy themselves that all necessary steps have been

taken to assure that each application and use meets all performance

and safety requirements, including any applicable laws, regulations,

codes and standards. In no event will Rockwell Automation be

responsible or liable for indirect or consequential damage resulting

from the use or application of these products.

Any illustrations, charts, sample programs, and layout examples

shown in this publication are intended solely for purposes of

example. Since there are many variables and requirements associated

with any particular installation, Rockwell Automation does not

assume responsibility or liability (to include intellectual property

liability) for actual use based upon the examples shown in this

publication.

Allen-Bradley publication SGI-1.1, Safety Guidelines for the

Application, Installation and Maintenance of Solid-State Control

(available from your local Rockwell Automation office), describes

some important differences between solid-state equipment and

electromechanical devices that should be taken into consideration

when applying products such as those described in this publication.

Reproduction of the contents of this copyrighted publication, in

whole or part, without written permission of Rockwell Automation, is

prohibited.

IMPORTANT ArmorBlock MaXum modules and media cables

are ordered and shipped separately.

ArmorBlock MaXum Robot I/O Cable Base and Kempf Box Plate 3

Publication 1792D-IN054B-EN-P - April 2003

Throughout this publication, notes may be used to make you aware

of safety considerations. The following annotations and their

accompanying statements help you to identify a potential hazard,

avoid a potential hazard, and recognize the consequences of a

potential hazard:

WARNING

Identifies information about practices or

circumstances that can cause an explosion in a

hazardous environment, which may lead to

personal injury or death, property damage, or

economic loss.

ATTENTION

Identifies information about practices or

circumstances that can lead to personal injury or

death, property damage, or economic loss.

IMPORTANT

Identifies information that is critical for

successful application and understanding of the

product.

4ArmorBlock MaXum Robot I/O Cable Base and Kempf Box Plate

Publication 1792D-IN054B-EN-P - April 2003

ATTENTION

Environment and Enclosure

This equipment is intended for use in a Pollution

Degree 2 industrial environment, in overvoltage

Category II applications (as defined in IEC

publication 60664-1), at altitudes up to 2000 meters

without derating.

This equipment is considered Group 1, Class A

industrial equipment according to IEC/CISPR

Publication 11. Without appropriate precautions,

there may be potential difficulties ensuring

electromagnetic compatibility in other

environments due to conducted as well as radiated

disturbance.

This equipment is supplied as "enclosed"

equipment. It should not require additional system

enclosure when used in locations consistent with

the enclosure type ratings stated in the

Specifications section of this publication.

Subsequent sections of this publication may

contain additional information regarding specific

enclosure type ratings, beyond what this product

provides, that are required to comply with certain

product safety certifications.

See NEMA Standards publication 250 and IEC

publication 60529, as applicable, for explanations

of the degrees of protection provided by different

types of enclosure. Also, see the appropriate

sections in this publication, as well as the

Allen-Bradley publication 1770-4.1 ("Industrial

Automation Wiring and Grounding Guidelines"),

for additional installation requirements pertaining

to this equipment.

ArmorBlock MaXum Robot I/O Cable Base and Kempf Box Plate 5

Publication 1792D-IN054B-EN-P - April 2003

Install Your ArmorBlock Cable Base

To install the cable base:

•Mount the cable base

•Attach the module to the base

•Attach the cables

These procedures are explained in detail in the following sections.

Mount the Cable Base

The cable base can be mounted either vertically or horizontally, using

3 screws. Cable bases accommodate 4 or 8 point ArmorBlock MaXum

modules. You must allow additional space for installation of 8 point

ArmorBlock MaXum module, which are longer than 4 point modules.

43332

When

installing a

cable base

with an 8

connector

module,

allow for

the

additional

length.

1792D-CB23

1.34in

34mm

1.63in

41.5mm

6.10in

155mm

4 connector

module

8.23in

209mm

8 connector

module

1.90in

48.18mm

2.70in

68.5mm

1.42in

36mm

0.64in

16.25mm

0.26in

6.5mm

4.21in

107mm

2.27in

57.6mm

6.10in

155mm

1.35in

34.25mm

6ArmorBlock MaXum Robot I/O Cable Base and Kempf Box Plate

Publication 1792D-IN054B-EN-P - April 2003

1. Mount the MaXum Kempf plate to the Kempf box.

2. Mount the CB23 cable base to the gasket and the Kempf box.

The mounting instructions are illustrated below.

43339

MaXum Kempf plate

MaXum Kempf box

31467-m

MaXum CB23

gasket

MaXum Kempf plate

MaXum

Kempf box

ArmorBlock MaXum Robot I/O Cable Base and Kempf Box Plate 7

Publication 1792D-IN054B-EN-P - April 2003

Attach the Module to the Base

1. Position the module over the mounted cable base. Align the

three captive screws in the module with the accepting

receptacles in the base.

2. Tighten the screws with a torque of 8 inch-pounds to secure

the module to the base.

IMPORTANT Make sure you properly align the screws to

complete the connections between the module

contacts and the cable contacts.

WARNING

If you insert or remove the module while

backplane power is on, an electrical arc can

occur. This could cause an explosion in

hazardous location installations.

Be sure that power is removed or the area is

nonhazardous before proceeding.

43335

Screws must be

aligned properly to

complete contact

connections.

Contact

connections

8ArmorBlock MaXum Robot I/O Cable Base and Kempf Box Plate

Publication 1792D-IN054B-EN-P - April 2003

ArmorBlock MaXum I/O modules are described in the following

publications:

•1792D series of ArmorBlock MaXum Installation Instructions

•1792-TD001 ArmorBlock Technical Data

The DeviceNet Network uses advanced network technology,

producer/consumer communication, to increase network

functionality and throughput. Visit our web site at

http://www.ab.com/networks for producer/consumer technology

information and updates.

Attach the Cables

1. Attach your network cable and power cable (if used) to the

connectors.

2. Cover the power connector with a cap if it is not used.

ArmorBlock MaXum Robot I/O Cable Base and Kempf Box Plate 9

Publication 1792D-IN054B-EN-P - April 2003

3. Attach your I/O connector cables.

WARNING

If you connect or disconnect the DeviceNet cable

with power applied to this module or any device

on the network, an electrical arc can occur. This

could cause an explosion in hazardous location

installations.

Be sure that power is removed or the area is

nonhazardous before proceeding.

31463-m

Male

Female

Network

Out

10 ArmorBlock MaXum Robot I/O Cable Base and Kempf Box Plate

Publication 1792D-IN054B-EN-P - April 2003

WARNING

Use supply wires suitable for 30°C above

surrounding ambient.

WARNING

If you connect or disconnect wiring while the

field-side power is on, an electrical arc can occur.

This can cause an explosion in hazardous location

installations. Be sure that power is removed or the

area is nonhazardous before proceeding.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Rockwell Automation Industrieelektrik Handbücher

Rockwell Automation

Rockwell Automation 140G2-N Bedienungs- und Wartungsanleitung

Rockwell Automation

Rockwell Automation A-B Quality 194R-S1 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 48CR Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Guardmaster GuardShield Type 4 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 140G Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 525 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley ControlNet 1784-PCC Bedienungsanleitung

Rockwell Automation

Rockwell Automation Enwatch EK-44750C Referenzhandbuch

Rockwell Automation

Rockwell Automation Allen-Bradley 2090-KTPC-MA-AA Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley MegaDySC 1608M Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1606-XLS120E Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley MP-Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley CENTERLINE 2500 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex Active Front End... Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 700 Drive Frame 9 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 100-C60 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley CENTERLINE 800 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley ControlNet 1786 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 140G Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 700 Bedienungsanleitung

Rockwell Automation

Rockwell Automation C09 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley CrossBoard 141C-VN16 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 194U Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Kinetix 5700 Series Bedienungsanleitung

Beliebte Industrieelektrik Handbücher anderer Marken

Rexroth Indramat

Rexroth Indramat DURADRIVE SYSTEM200 Technisches Handbuch

Abtech

Abtech HVJB Series Leitfaden

Murata

Murata GRM0335C1H8R1DA01 Series Bedienungsanleitung

SAF-HOLLAND

SAF-HOLLAND CBX 5415.5 Bedienungsanleitung

Eaton

Eaton Ulusoy HMH24-04 Bedienungsanleitung

Murata

Murata GJM0335C1E4R4BB01 Series Bedienungsanleitung

Newlong

Newlong NP-7H Bedienungsanleitung

Stahl

Stahl 8575/12 Bedienungsanleitung

SI Pegasus Bedienungsanleitung

Murata

Murata GRM1555C1H2R7CA01 Seies Bedienungsanleitung

Murata

Murata GRM0225C1E6R4BA03 Series Bedienungsanleitung

Cooper Power Systems

Cooper Power Systems VXE15 Bedienungsanleitung

S&C

S&C Vista SD Bedienungsanleitung

Murata

Murata GRM0335C2A7R3CA01 Series Bedienungsanleitung

Siemens

Siemens 3VA9988-0BM10 Bedienungsanleitung

Siemens

Siemens SITRANS LVS100 Bedienungsanleitung

Murata

Murata GRM32ER60G227ME05 Series Bedienungsanleitung

Phasemation

Phasemation DG-100 Bedienungsanleitung