RODE Microphones VideoMic Bedienungsanleitung

80Hz

VideoMicTM

Parts Guide

Mic Controls

quickstart

guide

VideoMicTM

www.rodemic.com

1. Foam windshield

2. Camera shoe mount

3. Battery cover

4. PAD switch (inside battery compartment)

warranty.rodemic.com/videomic

Scan the QR code to

Don’t FORGET

to register for your

FREE ten year warranty!

The RØDE VideoMicTM features an integrated

shock mount based on Rycote®Lyre®technology.

Constructed from a single piece of hard-wearing

thermoplastic, the Lyre®provides superior acoustic

suspension to traditional elastic solutions,

and will never wear out, sag or snap.

RØDE SOUNDBOOTH

now for Broadcast mics

Hear and compare RØDE microphones

at www.rodemic.com/soundbooth or on your iPad®

5. LED power indicator

6. Power and HPF switch

7. Integrated Rycote®Lyre®suspension

8. 3.5mm dual mono output cable

The High Pass Filter (HPF ) is a low frequency cut-off setting, which you can use

to remove rumble, camera noise or other low frequency noise while recording.

Mic ON

using High Pass Filter

Mic ON

Flat setting

Battery OFF

Mic mute

LED power

indicator

028_952_1_Videomic_Quickstart.indd 1028_952_1_Videomic_Quickstart.indd 1 17/12/2012 8:45:19 AM17/12/2012 8:45:19 AM

0dB

-10dB

-20dB

The LED power indicator next to the

On/Off switch will turn red when the

battery is running low. The mic will

work for approximately one hour once

the red indicator is lit, however with

reduced performance.

1. Turn the tightening ring counter-

clockwise to loosen the camera shoe

connection, before attaching to camera.

Securing the cable will

eliminate undesired noise

caused by cable movement.

The cable can be secured

in one of two orientations,

depending on the location

of your camera’s “Audio In”

socket.

See diagram 1 for cameras

with mic socket on the left.

See diagram 2for cameras

with mic socket on the right.

2. Slide the camera-shoe into place on the

camera mount. When the mic is in place,

secure it by gently tightening the ring

clockwise.

3. Connect the VideoMic’s audio lead to

the camera’s “Audio In” or “Mic” socket,

and secure the cable in place using the

in-built cable clips (see below).

mounting to camera

securing the cable

PAD switchbattery

The VideoMic comes with a three-position

PAD switch which is located inside the battery

compartment.

The PAD provides a selectable 10 or 20db

reduction of the input sensitivity, reducing

the output level when recording loud sound

sources, so that the optimal level can be

achieved in a wide range of situations.

To change the battery, gently push

and slide the battery cover off. Insert a

standard 9V battery with the positive

(+) end upwards.

The VideoMic uses a standard 9V

battery. With a good quality Alkaline

or Lithium battery, the VideoMic will

run for up to 100 continuous hours. We

recommend you remove the battery

if storing your VideoMic for extended

periods without use.

–

Push the cable in from the bottom.

028_952_1_Videomic_Quickstart.indd 2028_952_1_Videomic_Quickstart.indd 2 17/12/2012 8:46:21 AM17/12/2012 8:46:21 AM

Andere Handbücher für VideoMic

Dieses Handbuch passt für folgende Modelle

Andere RODE Microphones Mikrofon Handbücher

RODE Microphones

RODE Microphones NT4 Handbuch

RODE Microphones

RODE Microphones WIRELESS GO Bedienungsanleitung

RODE Microphones

RODE Microphones NT 2 Handbuch

RODE Microphones

RODE Microphones PODCASTER Bedienungsanleitung

RODE Microphones

RODE Microphones VideoMic Me-C Bedienungsanleitung

RODE Microphones

RODE Microphones PSA-1 Bedienungsanleitung

RODE Microphones

RODE Microphones NT 3 Handbuch

RODE Microphones

RODE Microphones NT1000 Bedienungsanleitung

RODE Microphones

RODE Microphones M1-S Bedienungsanleitung

RODE Microphones

RODE Microphones STEREO VIDEOMIC PRO Bedienungsanleitung

RODE Microphones

RODE Microphones TX3-XLR Bedienungsanleitung

RODE Microphones

RODE Microphones S1 Bedienungsanleitung

RODE Microphones

RODE Microphones NT 3 Bedienungsanleitung

RODE Microphones

RODE Microphones VideoMic GO Betriebsanleitung

RODE Microphones

RODE Microphones NTG-1 Bedienungsanleitung

RODE Microphones

RODE Microphones NTG8 Bedienungsanleitung

RODE Microphones

RODE Microphones M2 Bedienungsanleitung

RODE Microphones

RODE Microphones NT55 Bedienungsanleitung

RODE Microphones

RODE Microphones NT-USB Bedienungsanleitung

RODE Microphones

RODE Microphones K2 Handbuch

RODE Microphones

RODE Microphones Lavalier Bedienungsanleitung

RODE Microphones

RODE Microphones NT2-A Bedienungsanleitung

RODE Microphones

RODE Microphones VideoMic Me Bedienungsanleitung

RODE Microphones

RODE Microphones NT4 Bedienungsanleitung

Beliebte Mikrofon Handbücher anderer Marken

IK Multimedia

IK Multimedia iRig Stream MIC PRO Bedienungsanleitung

DAPAudio

DAPAudio RM-101 Bedienungsanleitung

AKG

AKG CHM 21 Bedienungsanleitung

Sennheiser

Sennheiser evolution wireless series EM 100 Bedienungsanleitung

Sony

Sony C-48 Bedienungsanleitung

GIGAMEDIA

GIGAMEDIA GGM PAMICUHFG Bedienungsanleitung

Shure

Shure WH30TQG Bedienungsanleitung

auna PRO

auna PRO MIC-900 Bedienungsanleitung

AKG

AKG D 3800 Bedienungsanleitung

Shure

Shure KSM141 Bedienungsanleitung

MAIIN SOUND

MAIIN SOUND IIN style Bedienungsanleitung

Earthworks

Earthworks TC25 Bedienungsanleitung

Sennheiser

Sennheiser evolution D1 Bedienungsanleitung

Alesis

Alesis MicLink Wireless Bedienungsanleitung

DSPPA

DSPPA D6234 Bedienungsanleitung

Monacor

Monacor IMG STAGELINE ECM-300B Bedienungsanleitung

Ansr Audio

Ansr Audio Scan16 Bedienungsanleitung

Shure

Shure MXA710 Series Bedienungsanleitung