Rohde & Schwarz RT-ZF5 Bedienungsanleitung

R&S®RT-ZF5

Ethernet Probing Fixture

Manual

Version 02

1333231802

(=QGB2)

This manual describes the R&S RT-ZF5 Ethernet probing fixture (1333.0896.02).

Mühldorfstr. 15, 81671 München, Germany

Phone: +49 89 41 29 - 0

Fax: +49 89 41 29 12 164

Email: [email protected]

Internet: www.rohde-schwarz.com

Subject to change – Data without tolerance limits is not binding.

R&S® is a registered trademark of Rohde & Schwarz GmbH & Co. KG.

Trade names are trademarks of the owners.

Throughout this manual, products from Rohde & Schwarz are indicated without the ® symbol, e.g.

R&S®RT-ZF5 is indicated as R&S RT-ZF5.

Safety Information

R&S®RT-ZF5

3Manual 1333.2318.02 ─ 02

1 Safety Information

The product documentation helps you to use the product safely and efficiently.

Keep the product documentation nearby and offer it to other users.

Safety information warns you about the potential dangers and gives instructions

how to prevent personal injuries or damage caused by dangerous situations.

Throughout the documentation, safety instructions are provided when you need to

take care during setup or operation.

Intended use

The equipment under test (EUT) is a signal quality test and development board,

indented to be used at laboratory or test and measurement areas. These areas

are used for analysis, testing and servicing and where equipment is operated by

trained personnel.

Operating site

Only use the product indoors, and keep it dry. The product has no casing and is

sensitive to moisture and humidity.

The product is suitable for pollution degree 2 environments where nonconductive

contamination can occur. For more information on environmental conditions such

as ambient temperature, see the specifications.

Installation

Make sure to connect only Ethernet devices with RJ-45 interface that are

designed according to IEEE802.3 10BASE-T, 100BASE-T/TX, 100BASE-T1,

1000BASE-T, or 10GBASE-T.

ESD and EMI impact

The product is sensitive to electrostatic discharge (ESD) because of open mod-

ules. Protect the work area against electrostatic discharge to avoid damage to

electronic components. Always work at a static-approved workstation.

Electromagnetic interference (EMI) can affect the measurement results. To avoid

any impact, use only USB cables shorter 3 m.

Product Description

R&S®RT-ZF5

4Manual 1333.2318.02 ─ 02

2 Product Description

The R&S RT-ZF5 test fixture is a multipurpose fixture to probe or tap Ethernet sig-

nals up to the 10GBASE-T standard.

The fixture can be used to separate the directions of a full duplex connection for

decoding applications like R&S RTO/R&S RTP-K57 (100BASE-T1).

The R&S RT-ZF5 can also be used for compliance testing of energy-efficient

Ethernet (100BASE-TX and 1000BASE-T). For compliance testing, it is used in

combination with:

●R&S RTO/R&S RTP oscilloscope

●EEE: R&S RTO-K86 (1333.1992.02), R&S RTP-K86 (1337.8833.02): requires

R&S RTO/R&S RTP-K22

●R&S ScopeSuite software

For data, see the "R&S RT-ZFxx Oscilloscope Test Fixtures - Specifications" at

www.rohde-schwarz.com/brochure-datasheet/rto.

2.1 Deliveries

The R&S RT-ZF5 delivery package contains the following items:

●R&S RT-ZF5 test board

●Manual

2.2 Board Description

The R&S RT-ZF5 Ethernet probing fixture has three labeled sections, which are

designed for specific test cases. You can cut the board at the section limits and

use each section as a separate board.

"Directional Probe" section

Separates the signals on a (differential) full duplex Ethernet connection (like

1000BASE-T or 100BASE-T1) into a forward signal and a backward signal. The

Board Description

Product Description

R&S®RT-ZF5

5Manual 1333.2318.02 ─ 02

fixture supports all four Ethernet lanes in parallel. The couplers deliver -15 dB of

the original signal amplitude.

" Load and Probe" section

Terminates the signals with 100 Ω and offers pins for differential probing.

"DUT and Link Partner" section

Used to tap the connection between two Ethernet devices. It offers pins for differ-

ential and single-ended probes to ground probe connections.

RSRT-ZF5

Ethernet Probing Fixture

Directional

Probe

Load and Probe DUT and Link Partner

X100

DUT

X101

Link

Partner

X200

DUT

X210

DUT

X211

Link

Partner

C B

A D

C B

FWD REV FWD REV

X111

X113

X115

X117

X119

X121

X123

X125

X112

X114

X116

X118

X120

X122

X124

X126

Figure 2-1: R&S

RT-ZF5 Ethernet probing fixture

Board Description

Connecting the Board

R&S®RT-ZF5

6Manual 1333.2318.02 ─ 02

Figure 2-2: Wiring diagram of the Directional Probe section

3 Connecting the Board

The appropriate DUT and probe connection depends on the test case. The

R&S ScopeSuite software provides a step-by-step guide that shows the required

setup for each test case.

The test preparation and measurements of the test cases are described in the

"R&S®RTO, R&S®RTP Ethernet Compliance Tests, Test Procedures Manual".

Inhaltsverzeichnis

Andere Rohde & Schwarz Prüfgeräte Handbücher

Rohde & Schwarz

Rohde & Schwarz R&S AMS32-K31 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTH1004MSO Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTO64 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RT-ZF7 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz Hameg HMO3524 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz CMW 500 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz SMBVB-K362 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz VTS Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz Scope Rider RTH1004 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz SFQ Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTP Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz R&S TS-PIO4 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz ZV-Z58 Handbuch

Rohde & Schwarz

Rohde & Schwarz Hameg HMO3522 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz CMU 200 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz HMO1202 Series Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz Hameg IEEE-488 GBiP Interface HO740 Installationsanleitung

Rohde & Schwarz

Rohde & Schwarz RTM3000 Series Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTM3K-COM4 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz TSVP Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz CTS50 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz R&S CMW500 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTB2000 Series Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTE Series Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung