Rohde & Schwarz RTB2004 Bedienungsanleitung

R&S®RTB2000

Digital Oscilloscope

User Manual

1333.1611.02 ─ 04

(=Q@;2)

This manual describes the following R&S®RTB2000 models:

●R&S®RTB2002 (1333.1005K02)

●R&S®RTB2004 (1333.1005K04)

Mühldorfstr. 15, 81671 München, Germany

Phone: +49 89 41 29 - 0

Fax: +49 89 41 29 12 164

Email: [email protected]

Internet: www.rohde-schwarz.com

Subject to change – Data without tolerance limits is not binding.

R&S® is a registered trademark of Rohde & Schwarz GmbH & Co. KG.

Trade names are trademarks of their owners.

Throughout this manual, products from Rohde & Schwarz are indicated without the ® symbol, e.g. R&S®RTB is indicated as

R&S RTB2000.

1171.0000.42 - 09 Page 1

Basic Safety Instructions

Always read through and comply with the following safety instructions!

All plants and locations of the Rohde & Schwarz group of companies make every effort to keep the safety

standards of our products up to date and to offer our customers the highest possible degree of safety. Our

products and the auxiliary equipment they require are designed, built and tested in accordance with the

safety standards that apply in each case. Compliance with these standards is continuously monitored by

our quality assurance system. The product described here has been designed, built and tested in

accordance with the EC Certificate of Conformity and has left the manufacturer’s plant in a condition fully

complying with safety standards. To maintain this condition and to ensure safe operation, you must

observe all instructions and warnings provided in this manual. If you have any questions regarding these

safety instructions, the Rohde & Schwarz group of companies will be happy to answer them.

Furthermore, it is your responsibility to use the product in an appropriate manner. This product is designed

for use solely in industrial and laboratory environments or, if expressly permitted, also in the field and must

not be used in any way that may cause personal injury or property damage. You are responsible if the

product is used for any purpose other than its designated purpose or in disregard of the manufacturer's

instructions. The manufacturer shall assume no responsibility for such use of the product.

The product is used for its designated purpose if it is used in accordance with its product documentation

and within its performance limits (see data sheet, documentation, the following safety instructions). Using

the product requires technical skills and, in some cases, a basic knowledge of English. It is therefore

essential that only skilled and specialized staff or thoroughly trained personnel with the required skills be

allowed to use the product. If personal safety gear is required for using Rohde & Schwarz products, this

will be indicated at the appropriate place in the product documentation. Keep the basic safety instructions

and the product documentation in a safe place and pass them on to the subsequent users.

Observing the safety instructions will help prevent personal injury or damage of any kind caused by

dangerous situations. Therefore, carefully read through and adhere to the following safety instructions

before and when using the product. It is also absolutely essential to observe the additional safety

instructions on personal safety, for example, that appear in relevant parts of the product documentation. In

these safety instructions, the word "product" refers to all merchandise sold and distributed by the Rohde &

Schwarz group of companies, including instruments, systems and all accessories. For product-specific

information, see the data sheet and the product documentation.

Safety labels on products

The following safety labels are used on products to warn against risks and dangers.

Symbol

Meaning

Symbol

Meaning

Notice, general danger location

Observe product documentation

ON/OFF Power

Caution when handling heavy equipment

Standby indication

Danger of electric shock

Direct current (DC)

Basic Safety Instructions

1171.0000.42 - 09 Page 2

Symbol

Meaning

Symbol

Meaning

Caution ! Hot surface

Alternating current (AC)

Protective conductor terminal

To identify any terminal which is intended for

connection to an external conductor for

protection against electric shock in case of a

fault, or the terminal of a protective earth

Direct/alternating current (DC/AC)

Earth (Ground)

Class II Equipment

to identify equipment meeting the safety

requirements specified for Class II equipment

(device protected by double or reinforced

insulation)

Frame or chassis Ground terminal

EU labeling for batteries and accumulators

For additional information, see section "Waste

disposal/Environmental protection", item 1.

Be careful when handling electrostatic sensitive

devices

EU labeling for separate collection of electrical

and electronic devices

For additional information, see section "Waste

disposal/Environmental protection", item 2.

Warning! Laser radiation

For additional information, see section

"Operation", item 7.

Signal words and their meaning

The following signal words are used in the product documentation in order to warn the reader about risks

and dangers.

Indicates a hazardous situation which, if not avoided, will result in death or

serious injury.

Indicates a hazardous situation which, if not avoided, could result in death or

serious injury.

Indicates a hazardous situation which, if not avoided, could result in minor or

moderate injury.

Indicates information considered important, but not hazard-related, e.g.

messages relating to property damage.

In the product documentation, the word ATTENTION is used synonymously.

These signal words are in accordance with the standard definition for civil applications in the European

Economic Area. Definitions that deviate from the standard definition may also exist in other economic

areas or military applications. It is therefore essential to make sure that the signal words described here

are always used only in connection with the related product documentation and the related product. The

use of signal words in connection with unrelated products or documentation can result in misinterpretation

and in personal injury or material damage.

Basic Safety Instructions

1171.0000.42 - 09 Page 3

Operating states and operating positions

The product may be operated only under the operating conditions and in the positions specified by the

manufacturer, without the product's ventilation being obstructed. If the manufacturer's specifications are

not observed, this can result in electric shock, fire and/or serious personal injury or death. Applicable local

or national safety regulations and rules for the prevention of accidents must be observed in all work

performed.

1. Unless otherwise specified, the following requirements apply to Rohde & Schwarz products:

predefined operating position is always with the housing floor facing down, IP protection 2X, use only

indoors, max. operating altitude 2000 m above sea level, max. transport altitude 4500 m above sea

level. A tolerance of ±10 % shall apply to the nominal voltage and ±5 % to the nominal frequency,

overvoltage category 2, pollution degree 2.

2. Do not place the product on surfaces, vehicles, cabinets or tables that for reasons of weight or stability

are unsuitable for this purpose. Always follow the manufacturer's installation instructions when

installing the product and fastening it to objects or structures (e.g. walls and shelves). An installation

that is not carried out as described in the product documentation could result in personal injury or

even death.

3. Do not place the product on heat-generating devices such as radiators or fan heaters. The ambient

temperature must not exceed the maximum temperature specified in the product documentation or in

the data sheet. Product overheating can cause electric shock, fire and/or serious personal injury or

even death.

Electrical safety

If the information on electrical safety is not observed either at all or to the extent necessary, electric shock,

fire and/or serious personal injury or death may occur.

1. Prior to switching on the product, always ensure that the nominal voltage setting on the product

matches the nominal voltage of the mains-supply network. If a different voltage is to be set, the power

fuse of the product may have to be changed accordingly.

2. In the case of products of safety class I with movable power cord and connector, operation is

permitted only on sockets with a protective conductor contact and protective conductor.

3. Intentionally breaking the protective conductor either in the feed line or in the product itself is not

permitted. Doing so can result in the danger of an electric shock from the product. If extension cords

or connector strips are implemented, they must be checked on a regular basis to ensure that they are

safe to use.

4. If there is no power switch for disconnecting the product from the mains, or if the power switch is not

suitable for this purpose, use the plug of the connecting cable to disconnect the product from the

mains. In such cases, always ensure that the power plug is easily reachable and accessible at all

times. For example, if the power plug is the disconnecting device, the length of the connecting cable

must not exceed 3 m. Functional or electronic switches are not suitable for providing disconnection

from the AC supply network. If products without power switches are integrated into racks or systems,

the disconnecting device must be provided at the system level.

5. Never use the product if the power cable is damaged. Check the power cables on a regular basis to

ensure that they are in proper operating condition. By taking appropriate safety measures and

carefully laying the power cable, ensure that the cable cannot be damaged and that no one can be

hurt by, for example, tripping over the cable or suffering an electric shock.

Basic Safety Instructions

1171.0000.42 - 09 Page 4

6. The product may be operated only from TN/TT supply networks fuse-protected with max. 16 A (higher

fuse only after consulting with the Rohde & Schwarz group of companies).

7. Do not insert the plug into sockets that are dusty or dirty. Insert the plug firmly and all the way into the

socket provided for this purpose. Otherwise, sparks that result in fire and/or injuries may occur.

8. Do not overload any sockets, extension cords or connector strips; doing so can cause fire or electric

shocks.

9. For measurements in circuits with voltages Vrms > 30 V, suitable measures (e.g. appropriate

measuring equipment, fuse protection, current limiting, electrical separation, insulation) should be

taken to avoid any hazards.

10. Ensure that the connections with information technology equipment, e.g. PCs or other industrial

computers, comply with the IEC 60950-1 / EN 60950-1 or IEC 61010-1 / EN 61010-1 standards that

apply in each case.

11. Unless expressly permitted, never remove the cover or any part of the housing while the product is in

operation. Doing so will expose circuits and components and can lead to injuries, fire or damage to the

product.

12. If a product is to be permanently installed, the connection between the protective conductor terminal

on site and the product's protective conductor must be made first before any other connection is

made. The product may be installed and connected only by a licensed electrician.

13. For permanently installed equipment without built-in fuses, circuit breakers or similar protective

devices, the supply circuit must be fuse-protected in such a way that anyone who has access to the

product, as well as the product itself, is adequately protected from injury or damage.

14. Use suitable overvoltage protection to ensure that no overvoltage (such as that caused by a bolt of

lightning) can reach the product. Otherwise, the person operating the product will be exposed to the

danger of an electric shock.

15. Any object that is not designed to be placed in the openings of the housing must not be used for this

purpose. Doing so can cause short circuits inside the product and/or electric shocks, fire or injuries.

16. Unless specified otherwise, products are not liquid-proof (see also section "Operating states and

operating positions", item 1). Therefore, the equipment must be protected against penetration by

liquids. If the necessary precautions are not taken, the user may suffer electric shock or the product

itself may be damaged, which can also lead to personal injury.

17. Never use the product under conditions in which condensation has formed or can form in or on the

product, e.g. if the product has been moved from a cold to a warm environment. Penetration by water

increases the risk of electric shock.

18. Prior to cleaning the product, disconnect it completely from the power supply (e.g. AC supply network

or battery). Use a soft, non-linting cloth to clean the product. Never use chemical cleaning agents such

as alcohol, acetone or diluents for cellulose lacquers.

Operation

1. Operating the products requires special training and intense concentration. Make sure that persons

who use the products are physically, mentally and emotionally fit enough to do so; otherwise, injuries

or material damage may occur. It is the responsibility of the employer/operator to select suitable

personnel for operating the products.

Basic Safety Instructions

1171.0000.42 - 09 Page 5

2. Before you move or transport the product, read and observe the section titled "Transport".

3. As with all industrially manufactured goods, the use of substances that induce an allergic reaction

(allergens) such as nickel cannot be generally excluded. If you develop an allergic reaction (such as a

skin rash, frequent sneezing, red eyes or respiratory difficulties) when using a Rohde & Schwarz

product, consult a physician immediately to determine the cause and to prevent health problems or

stress.

4. Before you start processing the product mechanically and/or thermally, or before you take it apart, be

sure to read and pay special attention to the section titled "Waste disposal/Environmental protection",

item 1.

5. Depending on the function, certain products such as RF radio equipment can produce an elevated

level of electromagnetic radiation. Considering that unborn babies require increased protection,

pregnant women must be protected by appropriate measures. Persons with pacemakers may also be

exposed to risks from electromagnetic radiation. The employer/operator must evaluate workplaces

where there is a special risk of exposure to radiation and, if necessary, take measures to avert the

potential danger.

6. Should a fire occur, the product may release hazardous substances (gases, fluids, etc.) that can

cause health problems. Therefore, suitable measures must be taken, e.g. protective masks and

protective clothing must be worn.

7. Laser products are given warning labels that are standardized according to their laser class. Lasers

can cause biological harm due to the properties of their radiation and due to their extremely

concentrated electromagnetic power. If a laser product (e.g. a CD/DVD drive) is integrated into a

Rohde & Schwarz product, absolutely no other settings or functions may be used as described in the

product documentation. The objective is to prevent personal injury (e.g. due to laser beams).

8. EMC classes (in line with EN 55011/CISPR 11, and analogously with EN 55022/CISPR 22,

EN 55032/CISPR 32)

 Class A equipment:

Equipment suitable for use in all environments except residential environments and environments

that are directly connected to a low-voltage supply network that supplies residential buildings

Note: Class A equipment is intended for use in an industrial environment. This equipment may

cause radio disturbances in residential environments, due to possible conducted as well as

radiated disturbances. In this case, the operator may be required to take appropriate measures to

eliminate these disturbances.

 Class B equipment:

Equipment suitable for use in residential environments and environments that are directly

connected to a low-voltage supply network that supplies residential buildings

Repair and service

1. The product may be opened only by authorized, specially trained personnel. Before any work is

performed on the product or before the product is opened, it must be disconnected from the AC supply

network. Otherwise, personnel will be exposed to the risk of an electric shock.

Basic Safety Instructions

1171.0000.42 - 09 Page 6

2. Adjustments, replacement of parts, maintenance and repair may be performed only by electrical

experts authorized by Rohde & Schwarz. Only original parts may be used for replacing parts relevant

to safety (e.g. power switches, power transformers, fuses). A safety test must always be performed

after parts relevant to safety have been replaced (visual inspection, protective conductor test,

insulation resistance measurement, leakage current measurement, functional test). This helps ensure

the continued safety of the product.

Batteries and rechargeable batteries/cells

If the information regarding batteries and rechargeable batteries/cells is not observed either at all or to the

extent necessary, product users may be exposed to the risk of explosions, fire and/or serious personal

injury, and, in some cases, death. Batteries and rechargeable batteries with alkaline electrolytes (e.g.

lithium cells) must be handled in accordance with the EN 62133 standard.

1. Cells must not be taken apart or crushed.

2. Cells or batteries must not be exposed to heat or fire. Storage in direct sunlight must be avoided.

Keep cells and batteries clean and dry. Clean soiled connectors using a dry, clean cloth.

3. Cells or batteries must not be short-circuited. Cells or batteries must not be stored in a box or in a

drawer where they can short-circuit each other, or where they can be short-circuited by other

conductive materials. Cells and batteries must not be removed from their original packaging until they

are ready to be used.

4. Cells and batteries must not be exposed to any mechanical shocks that are stronger than permitted.

5. If a cell develops a leak, the fluid must not be allowed to come into contact with the skin or eyes. If

contact occurs, wash the affected area with plenty of water and seek medical aid.

6. Improperly replacing or charging cells or batteries that contain alkaline electrolytes (e.g. lithium cells)

can cause explosions. Replace cells or batteries only with the matching Rohde & Schwarz type (see

parts list) in order to ensure the safety of the product.

7. Cells and batteries must be recycled and kept separate from residual waste. Rechargeable batteries

and normal batteries that contain lead, mercury or cadmium are hazardous waste. Observe the

national regulations regarding waste disposal and recycling.

8. Follow the transport stipulations of the carrier (IATA-DGR, IMDG-Code, ADR, RID) when returning

lithium batteries to Rohde & Schwarz subsidiaries.

Transport

1. The product may be very heavy. Therefore, the product must be handled with care. In some cases,

the user may require a suitable means of lifting or moving the product (e.g. with a lift-truck) to avoid

back or other physical injuries.

2. Handles on the products are designed exclusively to enable personnel to transport the product. It is

therefore not permissible to use handles to fasten the product to or on transport equipment such as

cranes, fork lifts, wagons, etc. The user is responsible for securely fastening the products to or on the

means of transport or lifting. Observe the safety regulations of the manufacturer of the means of

transport or lifting. Noncompliance can result in personal injury or material damage.

Instrucciones de seguridad elementales

1171.0000.42 - 09 Page 7

3. If you use the product in a vehicle, it is the sole responsibility of the driver to drive the vehicle safely

and properly. The manufacturer assumes no responsibility for accidents or collisions. Never use the

product in a moving vehicle if doing so could distract the driver of the vehicle. Adequately secure the

product in the vehicle to prevent injuries or other damage in the event of an accident.

Waste disposal/Environmental protection

1. Specially marked equipment has a battery or accumulator that must not be disposed of with unsorted

municipal waste, but must be collected separately. It may only be disposed of at a suitable collection

point or via a Rohde & Schwarz customer service center.

2. Waste electrical and electronic equipment must not be disposed of with unsorted municipal waste, but

must be collected separately.

Rohde & Schwarz GmbH & Co. KG has developed a disposal concept and takes full responsibility for

take-back obligations and disposal obligations for manufacturers within the EU. Contact your

Rohde & Schwarz customer service center for environmentally responsible disposal of the product.

3. If products or their components are mechanically and/or thermally processed in a manner that goes

beyond their intended use, hazardous substances (heavy-metal dust such as lead, beryllium, nickel)

may be released. For this reason, the product may only be disassembled by specially trained

personnel. Improper disassembly may be hazardous to your health. National waste disposal

regulations must be observed.

4. If handling the product releases hazardous substances or fuels that must be disposed of in a special

way, e.g. coolants or engine oils that must be replenished regularly, the safety instructions of the

manufacturer of the hazardous substances or fuels and the applicable regional waste disposal

regulations must be observed. Also observe the relevant safety instructions in the product

documentation. The improper disposal of hazardous substances or fuels can cause health problems

and lead to environmental damage.

For additional information about environmental protection, visit the Rohde & Schwarz website.

1171.0200.22-06.00

Customer Support

Technical support – where and when you need it

For quick, expert help with any Rohde & Schwarz equipment, contact one of our Customer Support

Centers. A team of highly qualified engineers provides telephone support and will work with you to find a

solution to your query on any aspect of the operation, programming or applications of Rohde & Schwarz

equipment.

Up-to-date information and upgrades

To keep your instrument up-to-date and to be informed about new application notes related to your

instrument, please send an e-mail to the Customer Support Center stating your instrument and your wish.

We will take care that you will get the right information.

Europe, Africa, Middle East Phone +49 89 4129 12345

[email protected]

North America Phone 1-888-TEST-RSA(1-888-837-8772)

[email protected]

Latin America Phone +1-410-910-7988

[email protected]

Asia/Pacific Phone +65 65 13 04 88

[email protected]

China Phone +86-800-810-8228 /

+86-400-650-5896

[email protected]

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Rohde & Schwarz Prüfgeräte Handbücher

Rohde & Schwarz

Rohde & Schwarz RTP044 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz R&S ATS1000 Handbuch

Rohde & Schwarz

Rohde & Schwarz RTB2000 Series Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTB2000 Series Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz HMO Compact Series Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTP Series Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz EDST300 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz Hameg IEEE-488 GBiP Interface HO740 Installationsanleitung

Rohde & Schwarz

Rohde & Schwarz ZV-Z58 Handbuch

Rohde & Schwarz

Rohde & Schwarz RTM3000 Series Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTP044B Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz ZV-Z53 Handbuch

Rohde & Schwarz

Rohde & Schwarz R&S QAR50 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz SMBVB-K362 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTE Series Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz R&S EPL1000 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz VTS Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz CMU 200 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTE-COM4 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz FSH-Z2 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz R&S RTM3000 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTM3K-COM2 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTA4000 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz ZV-Z129 Handbuch

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung