Roland V-Mixer M-200i Bedienungsanleitung

Booting/Quitting the M-200i Remote

Booting the M-200i Remote

Turn on the power of the iPad where the M-200i Remote is installed and tap the following icon.

g.icon.eps

Quitting the M-200i Remote

Press the home button of the iPad to quit the M-200i Remote.

Connecting the M-200i and iPad

Right after turning the power on, M-200i cannot communicate with iPad via DOCK cable, Wired LAN nor Wireless LAN. Check the

status indicator located right upper corner of the M-200i’s display before connection.

Display Description

Communication with iPad is not ready.

Connected to the Wireless LAN router. The signal strength (the strength of the radio waves from the Wireless LAN router) is indicated by

three bars.

A wireless USB adapter is attached, but no connection to the Wireless LAN router is in eect.

No wireless USB adapter is attached.

Ad-hoc mode.

* For details of iPad network setup, refer to its user guide.

* For setting of the wireless LAN access point, refer to its owner’s manual.

Network setting of the M-200i

Carry out the network setting on the NETWORK screen of the M-200i. Call up the NETWORK screen using the following steps.

1. Call up the SETUP screen.

Press the [SETUP] in the M-200i’s DISPLAY section to call up the SETUP screen.

2. Call up the NETWORK screen.

Select [NETWORK] in the SETUP screen and press the [ENTER].

* For details of network settings of the M-200i, refer to its owner’s manual. Go to “Network“ section.

Types of Connection

There are 3 types of connection for the M-200i and iPad:

• Wired Connection using the Dock Cable (p. 2)

• Wired to Wireless Connection using a LAN Cable and Wireless LAN Access Point (p. 2)

• Wireless Connection using a Wireless USB Adaptor

- Wireless Network via a Wireless LAN Access Point (p. 3)

- Wireless Ad-Hoc Connection (p. 3)

M-200i Remote Setup Guide

permission of ROLAND CORPORATION.

* All product names mentioned in this document are trademarks or registered trademarks of their respective owners.

1PS

M-200i Remote Setup Guide

Wired Connection using the DOCK cable

Use the accessory dock cable to connect the M-200i’s DOCK CABLE connector and the iPad’s Dock connector.

g.dock-cable-connection.eps

The accessory DOCK cable is for the 30 pin Dock connector. If you are connecting the iPad equipped with such connector (1st, 2nd and 3rd

generation), use the accessory cable. If your iPad is equipped with Lightning connector (4th Generation or iPad mini), use the Lightning - 30 pin

conversion cable.

Stable communication is possible using the DOCK cable. Further, the cable is capable of the power supply to the connected iPad. You can carry out

the remote control operations without concerning the battery life.

When connection is made using the DOCK cable, operation sounds of iPad are sent to the M-200i depending on the patchbay setting.

The remote control application “M-200i Remote”produces the operation sounds while you are setting the clock or editing names using the software

keyboard. To turn o the operation sounds of the iPad, go to [Settings] and select [Sounds]. Then turn o [Lock Sounds] and [Keyboard Clicks].

Wired to WirelessConnection using a LAN Cable and Wireless LAN Access Point

Connect the M-200i to the wireless LAN access point (e.g., wireless LAN router) using LAN cable rst. Then wirelessly connect the

iPad and the wireless LAN access point.

g.wired-connect-router.eps

1. Connect the M-200i with the wireless LAN access point

Use LAN cable to connect the M-200i’s LAN connector and the wireless LAN access point.

2. Connect iPad to the wireless LAN access point

Select [Settings] > [Wi-Fi] > [Choose a Network] on the iPad and select the wireless LAN access point where the M-200i is

connected.

M-200i Remote Setup Guide

Wireless Connection using a Wireless USB Adaptor

Connect the wireless USB adaptor (WNA1100-RL ; sold separately) to the M-200i and make it ready to use the wireless LAN function.

Wireless Connection via a Wireless LAN Access Point

Wirelessly connect the M-200i to a wireless LAN access point, such as a router, rst. Then wirelessly connect with iPad via the

wireless LAN access point.

g.router-wireless.eps

Wireless USB Adaptor

（WNA1100-RL; sold separately）

1. Connect the wireless USB adaptor to the M-200i.

Connect the separately sold WNA1100-RL to the M-200i’s WLAN ADAPTOR connector.

2. Connect the M-200i and the wireless LAN access point wirelessly.

Select WPS or the wireless LAN access point and establish the wireless connection.

* For details of network settings of the M-200i, refer to the M-200i’s owner’s manual. Go to “Network - LAN Setting“ section.

3. Connect iPad to the wireless LAN access point.

Select [Settings] > [Wi-Fi] > [Choose a Network] on the iPad and select the wireless LAN access point where the M-200i is

connected.

Ad-Hoc Connection

Using Ad-Hoc, you can connect your iPad and the M-200i directly.

g.adhoc-connect.eps

Wireless USB Adaptor

（WNA1100-RL; sold separately）

The iPad connected in Ad-Hoc mode will be unable to communicate with the Internet or with another wireless device. However, an iPad that has

cellular capability will be able to connect to the Internet via the cellular connection. Please be aware that if you use a cellular connection for Internet

connectivity, you may incur costs depending on your rate plan.

1. Connect the wireless USB adaptor to the M-200i.

Connect the separately sold WNA1100-RL to the M-200i’s WLAN ADAPTOR connector.

2. Turn the M-200i’s Ad-Hoc mode to on.

To turn the Ad-Hoc mode on/o, refer to the M-200i’s owner’s manual. Go to“Network - Making detailed settings for WIRELESS LAN -

Connecting in ad-hoc mode (AD-HOC)” section.

3. Establish the connection between the iPad and the M-200i.

On the iPad, select the M-200i’s Ad-Hoc SSID. The SSID can be found on the M-200i in [Settings] > [Wi-Fi] > [Choose a Network]. As

the password screen appears, input Ad-Hoc key shown on the M-200i’s screen.

M-200i Remote Setup Guide

Select the M-200i to Remote Control

1. Open the ONLINE screen.

Tap the [ONLINE] as shown below to open the ONLINE screen. Scanning of available M-200i units starts.

g.online_button.eps

2. Select the M-200i unit to communicate.

When this software detects any available units, a list as shown below appears. Tap to select the target unit.

• The device name of the M-200i connected using the DOCK cable is shown as [Dock].

• Device names of the LAN connected M-200i units are shown in the list. If multiple units are connected via LAN, set a dierent wireless ID for each

unit.

* For details of setting the wireless ID, refer to the M-200i’s owner’s manual. Go to “Network - Making detailed settings for WIRELESS LAN - Making

the setting for WIRELESS ID”section.

g.select_device.eps

3. Start communication with the M-200i.

Tap or slide right the [Online] switch on the ONLINE screen. The iPad starts communication with the selected M-200i unit.

g.online_sw_o.eps

M-200i Remote Setup Guide

If an M-200i unit cannot be found

If this software cannot nd any available M-200i unit, the message “M-200i not found” is displayed. In this case or if you cannot nd

the device name of the target M-200i unit, tap [Refresh] button to rescan.

g.device_not_found.eps

Quit the Communication

Tap or slide left the [Online] switch on the ONLINE screen. The iPad quits communication with the selected M-200i unit.

g.online_sw_on.eps

Further, the following operations may terminate the connection.

• Suspending the application

• Switching to another application

• Connecting to the notication center

If you want to prohibit such operations from being triggered by multi-task gesture or auto lock, select the corresponding items in [Setting] of your iPad

and turn them o.

M-200i Remote Setup Guide

Synchronizing with the Controls on the M-200i

Tap or slide right the [Sync knob and switch] switch to start synchronizing with the controls on the M-200i unit. Using switches or

dials on the M-200i unit, you can control this software.

* For details of synchronizing feature, refer to the M-200i Remote’s owner’s manual. Go to “Synchronizing the M-200i Operations and the Display of

this Software“.

g.sync_sw_o.eps

Quit Synchronizing

Tap or slide left the [Sync knob and switch] switch to quit synchronizing.

g.sync_sw_on.eps

You can start/quit synchronizing while the communication between an iPad and the M-200i is active.

Andere Handbücher für V-Mixer M-200i

Inhaltsverzeichnis

Andere Roland Musikmixer Handbücher

Roland

Roland MV-8000 Kurzanleitung

Roland

Roland CPM-120 Bedienungsanleitung

Roland

Roland V-studio VS-2480 Kurzanleitung

Roland

Roland DM-80F Bedienungsanleitung

Roland

Roland V-Mixer VM-C7100 Bedienungsanleitung

Roland

Roland S-1 Bedienungsanleitung

Roland

Roland VR-400UHD Gebrauchs- und Wartungshandbuch

Roland

Roland M-160 II Bedienungsanleitung

Roland

Roland V-Mixer VM-7200 Bedienungsanleitung

Roland

Roland M-5000 Bedienungsanleitung

Roland

Roland VK-7 Bedienungsanleitung

Roland

Roland VS-700C Bedienungsanleitung

Roland

Roland M-5000 Bedienungsanleitung

Roland

Roland VM-7000 Series Bedienungsanleitung

Roland

Roland Groovebox MC-307 Bedienungsanleitung

Roland

Roland M-160 Bedienungsanleitung

Roland

Roland PA-200 Bedienungsanleitung

Roland

Roland U-8ST Bedienungsanleitung

Roland

Roland Sonar V-Studio VS-700 Bedienungsanleitung

Roland

Roland Groovebox D2 Bedienungsanleitung

Roland

Roland SPD-SX Bedienungsanleitung

Roland

Roland M-480 Bedienungsanleitung

Roland

Roland MC-101 Bedienungsanleitung

Roland

Roland Groovebox MC-707 Bedienungsanleitung

Beliebte Musikmixer Handbücher anderer Marken

Neve

Neve 8816 Bedienungsanleitung

Mackie

Mackie Onyx Analogue Mixer Bedienungsanleitung

Behringer

Behringer EUROPOWER PMP518M Bedienungsanleitung

Peavey

Peavey S-32 Sanctuary Series Bedienungsanleitung

Rane

Rane MP 4 Bedienungsanleitung

True

True T9 Touchscreen Console Bedienungsanleitung

Studiomaster

Studiomaster Air Pro 24 Bedienungsanleitung

Pioneer

Pioneer SVM 1000 - Audio/Video Mixer Bedienungsanleitung

Yamaha

Yamaha MR1642 Bedienungsanleitung

Ecler

Ecler MAC40v Bedienungsanleitung

Pioneer

Pioneer DJM 909 - Battle Mixer W/Effects Bedienungsanleitung

Veeder-Root

Veeder-Root TLS-350 Series Bedienungsanleitung

Alto

Alto APM80.QUAD Bedienungsanleitung

Omnitronic

Omnitronic PM-211 Bedienungsanleitung

SoundCraft

SoundCraft B400 Bedienungsanleitung

CARVIN

CARVIN RX 1200 Bedienungsanleitung

Euphonix

Euphonix MC Mix Bedienungsanleitung

Mackie

Mackie Ultra-34 Bedienungsanleitung