Roland HB-12 Bedienungsanleitung

DSA121

DYX362

Mode indicator

• Light: Press the [Preheat] key to start preheating

• Flashing: Preheating under way

• Off: Preheating completed

Tray

Printer

(BT-12)

Finisher

(This machine HB-12)

Front Cover

Mode Switching

Lever

Time/temperature indicator [Temperature] key [Preheat] key*1 [Power] key

[Time] key [Stop/Unlock] key

Control Panel

Guide to Components of the Finisher

This guide describes the basic printing procedures using the

printer and this machine. In the next pages, the procedures

for each step and particular cautions are explained.

For safe and correct use, be sure to read Safety Information

before using the machine.

Quick Guide

Basic Usage of the Finisher

CAUTION:

• A parent or guardian must be present if infants, children, or people who need assistance use the ma-

chine, and they should be very careful when using it. Otherwise, injury or burns may result.

The finisher has “Standard mode”, “Professional mode”, and “Professional 2 mode”.

◆Standard mode

The factory-default setting is standard mode. The finisher has the following functions

to prevent children from touching the inside of the finisher accidentally when it is very

hot.

• When the inside of the finisher exceeds 70 °C (158 °F), the front cover locks. To

open the front cover, press the [Stop/ Unlock] key for at least 1 second.

The surface of the heater and the fabric are not in contact with each other during the

fixing process, so the surface of the heater does not become dirty.

◆Professional mode

To use this mode, switch from standard mode.

As this mode is for users who are accustomed to using the finisher, the front cover

does not lock even when the temperature of the inside of the finisher exceeds 70 °C

(158 °F).

However, during press processing and fixing processing, the front cover locks regard-

less of whatever mode is used to prevent erroneous operations.

The surface of the heater and the fabric are not in contact with each other during the

fixing process, so the surface of the heater does not become dirty.

◆Professional 2 mode

This mode minimizes the loss of color when T-shirts are washed.

To use this mode, switch from professional mode.

As this mode is for users who are accustomed to using the finisher, the front cover

does not lock even when the temperature of the inside of the finisher exceeds 70 °C

(158 °F).

However, during press processing and fixing processing, the front cover locks regard-

less of whatever mode is used to prevent erroneous operations.

The surface of the heater and the fabric are in contact with each other during the fixing

process, so regular cleaning of the surface of the heater is necessary.

* Refer to Operating Instructions for cleaning frequency and precautions.

◆How to Switch Modes

Press the [Temperature] key and

[Time] key simultaneously for at least

2 seconds.

DYX353

The operating mode changes as fol-

lows.

Standard mode

Professional

2 mode

Professional

mode

DYX354

◆Unlock Cover

When set to standard mode, press

the [Stop/ Unlock] key for at least 1

second.

DYX360

When set to the professional mode,

it is not necessary to hold down the

[Stop/Unlock] key.

Operating Procedure

Perform the procedures in the order of 1, 2, 3, and then 4.

The following settings and procedures are examples for major fabrics.

Depending on your environment, discoloration may occur or the ink may not be fixed prop-

erly. Before configure the settings, check the fixability of the fabric you use.

Fabric type Mode Temperature 1. Preparation 2. Pressing 3. Printing 4. Fixing

T-shirt Standard mode

Professional

mode

170°C (338°F) See next

page.

30sec See BT-12

Operating

Instructions.

3min

Professional 2

mode

180°C (356°F) 30sec 30sec

3min

Tote bag (thick) Standard mode

Professional

mode

170°C (338°F) 30sec 3min

Tote bag (thin) 150°C (302°F) 30sec 3min

Sweatshirts 170°C (338°F) 30sec 3min

Printed in Japan

EN GB EN US EN AU J089-7032

R1-181105 FA01418

Preparation

Loading the fabric in the tray

For details, refer to User’s Guide provided with the printer BT-12.

You can shorten the processing time by putting a garment in the tray while preheating the

finisher.

➊

Press the [Power] key to turn on the power..

➍

Set the amount of time that the heater is on.

Set the time according to the fabric on which you

are printing. The default setting is “Medium”.

➋

Make sure the mode switching lever is set in the

center.

➎

When the [Preheat] key is lit, press the [Preheat]

key to start preheating.

When the [Preheat] key is unlit, no operation is

necessary because preheating is completed.

➌

Set the temperature of the heater.

Set the temperature according to the fabric on which

you are printing. The default setting is “High”

Procedure for ( )

➊

When you move the mode switching lever to the

left, processing starts. An alarm sounds after pre-

heating is completed.

➋

Procedure for ( )

➊

When you move the mode switching lever to the

right, processing starts. An alarm sounds after

preheating is completed.

➋

Andere Roland Drucker Handbücher

Roland

Roland FJ-50 Bedienungsanleitung

Roland

Roland VersaUV LEF2-300 Betriebsanleitung

Roland

Roland SOLJET Pro III XC-540 Bedienungsanleitung

Roland

Roland VersaCAMM SP-300S Bedienungsanleitung

Roland

Roland EGX-600 Bedienungsanleitung

Roland

Roland SOLJET PROIII XC-540 Bedienungsanleitung

Roland

Roland VersaCamm VP-540 Bedienungsanleitung

Roland

Roland SOLJET PROIII XC-540 Bedienungsanleitung

Roland

Roland SJ-740 Bedienungsanleitung

Roland

Roland EGX-600 Bedienungs- und Wartungshandbuch

Roland

Roland versaUV lec-540 Bedienungsanleitung

Roland

Roland SP-300 Bedienungsanleitung

Roland

Roland VersaUV LEJ-640 Bedienungsanleitung

Roland

Roland SP-540i Bedienungsanleitung

Roland

Roland AJ-1000 Bedienungsanleitung

Roland

Roland Versa UV LEF-12 Bedienungsanleitung

Roland

Roland Metaza MPX-80 Bedienungsanleitung

Roland

Roland TrueVIS SG3-540 Bedienungsanleitung

Roland

Roland ColorCamm PC-12 Bedienungsanleitung

Roland

Roland VersaUV LEF-12 Gebrauchs- und Pflegehandbuch

Roland

Roland VersaUV LEF-20 Gebrauchs- und Pflegehandbuch

Roland

Roland VS-640i Bedienungsanleitung

Roland

Roland VersaCAMM ECO-SOL MAX3 Bedienungsanleitung

Roland

Roland SOLJET PROIII XC-540 Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Lexmark

Lexmark 1400 Series Handbuch

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Epson

Epson ET-7750 Betriebsanleitung

Canon

Canon CLBR 460ps Bedienungsanleitung

Eltron

Eltron P210 Guide Bedienungsanleitung

Ricoh

Ricoh MD-P1 Bedienungsanleitung

Epson

Epson SC-F7100 series Bedienungsanleitung

Epson

Epson Stylus C40UX Bedienungsanleitung

Canon

Canon imagePASS-A2 Bedienungsanleitung

Canon

Canon S820D Bedienungsanleitung