Roland Color Camm Pro PC-60 Bedienungsanleitung

PC-60PC-60

PC-60

USER'S MANUAL

Thank you very much for purchasing the PC-60.

• To ensure correct and safe usage with a full understanding of

this product's performance, please be sure to read through this

manual completely and store it in a safe location.

• Unauthorized copying or transferral, in whole or in part, of this

manual is prohibited.

• The contents of this operation manual and the specifications of

this product are subject to change without notice.

• The operation manual and the product have been prepared and

tested as much as possible. If you find any misprint or error,

please inform us.

• Roland DG Corp. assumes no responsibility for any direct or

indirect loss or damage which may occur through use of this

product, regardless of any failure to perform on the part of this

product.

• Roland DG Corp. assumes no responsibility for any direct or

indirect loss or damage which may occur with respect to any

article made using this product.

NOTICE Grounding Instructions

Do not modify the plug provided - if it will not fit the outlet,

have the proper outlet installed by a qualified electrician.

Check with qualified electrician or service personnel if the

grounding instructions are not completely understood, or if in

doubt as to whether the tool is properly grounded.

Use only 3-wire extension cords that have 3-prong

grounding plugs and 3-pole receptacles that accept the tool’s

plug.

Repair or replace damaged or worn out cord immediately.

Operating Instructions

KEEP WORK AREA CLEAN. Cluttered areas and benches

invites accidents.

DON’T USE IN DANGEROUS ENVIRONMENT. Don’t

use power tools in damp or wet locations, or expose them to

rain. Keep work area well lighted.

DISCONNECT TOOLS before servicing; when changing

accessories, such as blades, bits, cutters, and like.

REDUCE THE RISK OF UNINTENTIONAL STARTING.

Make sure the switch is in off position before plugging in.

USE RECOMMENDED ACCESSORIES. Consult the

owner’s manual for recommended accessories. The use of

improper accessories may cause risk of injury to persons.

NEVER LEAVE TOOL RUNNING UNATTENDED.

TURN POWER OFF. Don’t leave tool until it comes to a

complete stop.

For the USA

FEDERAL COMMUNICATIONS COMMISSION

RADIO FREQUENCY INTERFERENCE

STATEMENT

This equipment has been tested and found to comply with the

limits for a Class A digital device, pursuant to Part 15 of the

FCC Rules.

These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated

in a commercial environment.

This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance

with the instruction manual, may cause harmful interference

to radio communications.

Operation of this equipment in a residential area is likely to

cause harmful interference in which case the user will be

required to correct the interference at his own expense.

Unauthorized changes or modification to this system can void

the users authority to operate this equipment.

The I/O cables between this equipment and the computing

device must be shielded.

For Canada

CLASS A NOTICE

This Class A digital apparatus meets all requirements of the

Canadian Interference-Causing Equipment Regulations.

CLASSE A AVIS

Cet appareil numérique de la classe A respecte toutes les

exigences du Règlement sur le matériel brouilleur du

Canada.

ROLAND DG CORPORATION

1-6-4 Shinmiyakoda, Hamamatsu-shi, Shizuoka-ken, JAPAN 431-2103

MODEL NAME : See the MODEL given on the rating plate.

RELEVANT DIRECTIVE : EC MACHINERY DIRECTIVE (89/392/EEC)

EC LOW VOLTAGE DIRECTIVE (73/23/EEC)

EC ELECTROMAGNETIC COMPATIBILITY DIRECTIVE (89/336/EEC)

WARNING

This is a Class A product. In a domestic environment this product may cause radio interference in which

case the user may be required to take adequate measures.

Table of Contents

To Ensure Safe Use...............................................................................................................2

About the Labels Affixed to the Unit...............................................................4

Chapter 1 - Introduction

Checking Supplied Items............................................................................................................5

Part Names and Functions.........................................................................................................5

Set-up and Connections .............................................................................................................8

Installing the DRIVER ............................................................................................................... 10

Using with Windows®95 ..................................................................................................................... 11

Using with Windows®3.1 .................................................................................................................... 14

Chapter 2 - Basic Operation

1 DIP Switch Settings............................................................................................................... 18

2 Powering On............................................................................................................................ 19

3 Loading the Material ............................................................................................................. 20

To Perform Long Printing/Cutting..................................................................................................... 24

4 Installing a Blade ................................................................................................................... 25

5 Installing a Ribbon Cartridge.............................................................................................. 26

The COLOR LED Flashes and Operation Stops... .................................................................... 28

6 Cut Test & Self-test................................................................................................................ 29

7 Setting the Base Point.......................................................................................................... 31

8 Downloading Printing/Cutting Data .................................................................................. 32

9 Pausing and Stopping Operation ...................................................................................... 32

10 Cutting Off or Detaching the Material .............................................................................. 33

11 Powering Off ........................................................................................................................... 34

Chapter 3 - User's Reference

Tips and Tricks for Printing/Cutting ..................................................................................... 35

About the Printing/Cutting Area ............................................................................................ 37

About the Blade.......................................................................................................................... 37

Care and Maintenance.............................................................................................................. 38

What to Do If... ............................................................................................................................................ 39

Specifications of PC-60............................................................................................................................ 42

Windows is a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries.

IBM is a registered trademark of International Business Corporation.

Macintosh is a registered trademark of Apple Computer, Inc. in the USA and other countries.

To Ensure Safe Use

Used for instructions intended to alert the user to the risk of death or severe

injury should the unit be used improperly.

About and Notices

Used for instructions intended to alert the user to the risk of injury or material

damage should the unit be used improperly.

* Material damage refers to damage or other adverse effects caused with

respect to the home and all its furnishings, as well to domestic animals or

pets.

About the Symbols

The symbol alerts the user to important instructions or warnings. The specific meaning of

the symbol is determined by the design contained within the triangle. The symbol at left means

"danger of electrocution."

The symbol alerts the user to items that must never be carried out (are forbidden). The

specific thing that must not be done is indicated by the design contained within the circle. The

symbol at left means the unit must never be disassembled.

The symbol alerts the user to things that must be carried out. The specific thing that must

be done is indicated by the design contained within the circle. The symbol at left means the

power-cord plug must be unplugged from the outlet.

Do not disassemble, repair, or

modify.

Doing so may lead to fire or abnormal

operation resulting in injury.

Do not use with any electrical power

supply that does not meet the

ratings displayed on the unit.

Use with any other power supply may lead

to fire or electrocution.

Ground the unit with the ground

wire.

Failure to do so may result in risk of

electrical shock in the even of a mechanical

problem

Do not use while in an abnormal

state (i.e., emitting smoke, burning

odor, unusual noise, or the like).

Doing so may result in fire or electrical

shock. Immediately switch off first the sub

power, then the main power, unplug the

power cord from the electrical outlet, and

contact your authorized Roland dealer or

service center.

Do not allow liquids, metal objects

or flammables inside the machine.

Such materials

can cause fire.

Install in a level and stable location.

Otherwise the unit may tip over and cause

injury.

Use only with the power cord

included with this product.

Use with other than the included power cord

may lead to fire or electrocution.

Do not use with a damaged power

cord or plug, or with a loose electri-

cal outlet.

Use with any other

power supply may

lead to fire or

electrocution.

Do not injure or modify the electrical

power cord, nor subject it to exces-

sive bends, twists, pulls, binding, or

pinching, nor place any object of

weight on it.

Doing so may

damage the electri-

cal power cord,

leading to electrocu-

tion or fire.

When not in use for prolonged

periods, unplug the power cord from

the electrical outlet.

Failure to do so may

result in danger of

shock, electrocution,

or fire due to

deterioration of the

electrical insulation.

When unplugging the electrical

power cord from a power outlet,

grasp the plug, not the cord.

Unplugging by

pulling the cord

may damage it,

leading to fire or

electrocution.

Use the joining screws to secure the

unit to the stand.

Failure to do so

may result in

falling of the unit,

leading to injury.

Do not allow hands or hair to come

near the platen while the carriage is

in motion.

Failure to do so may result in injury due to

sudden movement of the carriage when the

power is switched on, when the sheet

loading lever is raised or lowered,

or when the

CUT TEST

key is

pressed.

Do not touch the area around the

printing carriage with the hands.

Failure to do so may result in burns.

Unpacking, installing, or relocating

the unit are operations which must

be carried out by two or more per-

sons holding the unit at its bottom

surface on the left and right sides.

Failure to do so may

result in dropping

the unit, leading

to injury.

Release the caster locks for the

stand before attempting to move.

Otherwise the unit may tip over and cause

injury.

Use care to avoid pinching the

fingers when placing the unit on the

stand.

Doing so may

result in injury.

Roll material must be placed at a

predetermined shaft position.

Failure to do so may

result in falling of the

roll, leading to injury.

About the Labels Affixed to the Unit

These labels are affixed to the body of this product.

The following figure describes the location.

: Indicates information to prevent machine breakdown or malfunction and ensure correct use.

: Indicates a handy tip or advice regarding use.

In addition to the and symbols, the symbols shown below are also used.

NOTICE

Do not touch the area around the

printing carriage with the hands.

Ne touchez pas avec les mains la zone

située autour du chariot d' impression.

Model name

Rating label

Use a rated power supply.

Do not allow hands or hair to come near the platen while

the carriage is in motion.

N' approchez pas vos mains ni vos cheveux du plateau

de travail quand le chariot est en mouvement.

Power Cord

Check the following to make sure that you received all the items that were shipped along with the unit.

Checking Supplied Items

Chapter 1 - Introduction

Blade

(Carbide) Blade Holder Head Cleaner

Chapter 1 - Introduction

Checking Supplied Items / Part Names and Functions

Material for Test Cuts

Thermal transfer ribbon cartridge

C M Y K

PC-60 DRIVER for windows®95

PC-60 DRIVER for windows®3.1

User's Manual

Part Names and Functions

Do not put the hands inside the right-hand cover. Doing so may result in breakdown of the unit.

NOTICE

Part Names and Functions

Rear View

Sheet Loading Lever

Used to raise or lower the pinch rollers

when loading or unloading material.

Automatic setup is performed by loading

material and lowering the lever.

Main Power Switch

Power Connector (AC IN)

This connector accepts standard AC

power cord.

Front View

DIP Switches

Used to make various settings.

Material

Alignment Sticker

Platen

Knife Guide

Printing Carriage

This is where a ribbon cartridge is mounted in

the cartridge holder and printing is carried out.

Pinch Roller (Left)

Press material against the grit

roller. When loading material,

place the left roller inside the

left edge of the material to

correctly track it through the

machine.

Cleaning pad

* Please do not remove

this pad.

Removing it may

result in breakdown. Cutter Force Control Slider

This is used to set the blade force.

Pinch Roller (Right)

This presses the material against the grit roller.

Cutting Carriage

The blade holder is mounted here.

Cartridge Holder

This is where the ribbon cartridge is installed.

Front cover

Opening the front cover during printing or cutting causes operation

to be paused. Operation resumes when the front cover is closed.

No printing or cutting is performed while the front cover is opened.

When the front cover is closed, the unit detects the color and

location of the installed ribbon cartridge.

Grit Roller

Grit roller position

indicator

Operation Panel

Serial (RS-232C) Input

Connector

When connecting an IBM-compat-

ible computer to the PC-60, a series

(RS-232C) cable is inserted here.

Serial (RS-422) Input

Connector

When connecting a Macintosh

to the PC-60, the recommended

cable (Apple System Peripheral-

8 Cable) is inserted here.

Parallel (Centronics) Input Connector

In a parallel configuration, connect the parallel

cable here. This cable carries data to your computer.

LED state

POWER PIECE ROLL FRONT CARTRIGE BUSY COLOR BASE POINT

PC-60 status and operator action

COVER HOLDER / CLEAR

The pinch roller is not above the grit roller.

flashing flashing The loaded material is displaced from the sensor.

See “3 Loading the Material” .

flashing Printing of the leaded piece material has finished

Replace with a new piece material.

flashing The front cover is open.

Close the front cover.

Corresponding The ink ribbon at the corresponding location has been used up.

LED is flashing

Corresponding The cartridge at the corresponding location is installed incorrectly.

LED is flashing See “5 Installing a Ribbon Cartridge” .

A ribbon cartridge needed for printing is absent.

flashing Install the ribbon cartridge that is needed for printing.

( See “ The COLOR LED Flashes and Operation Stops... ” .)

The ink ribbon at the has been used up and printing cannot continue.

flashing flashing Install a new ribbon cartridge of the same color.

( See “ The COLOR LED Flashes and Operation Stops... ” .)

flashing flashing Data is being deleted

flashing flashing flashing flashing flashing flashing flashing flashing See “What to Do If...” .

Operation Panel

POWER LED

This lights up when the sub power source

has been switched on.

* "Material setup" refers to the state when material has been loaded and the sheet-loading lever has been lowered.

Error Codes

* This chart can be copied and affixed to the top of the PC-60 to serve as a handy reference.

POWER Key

This switches the sub power source on

and off.

FRONT COVER LED

During setup, this flashes when the front

cover is opened. Closing the front cover

causes it to remain lit continuously.

BASE POINT/ CLEAR

LED

Setting a base point illuminates this LED.

The LED flashes while data is being

deleted.

BASE POINT/ CLEAR

Key

Sets the current position of the blade to

the base point for printing or cutting.

This key can be used only after material

has been loaded.

Holding down this key until the CLEAR

LED starts to flash deletes the data being

received.

BUSY LED

This flashes while receiving or deleting

data.

Cursor Keys

The , , , and keys

are used to move the carriage.

PIECE LED / ROLL LED

The corresponding LED flashes when

the material type is solenoid, then

remains lit continuously when setup is

completed.

COLOR LED

This lights up when cartridges for all

colors (CMYK) have been installed and

full-color printing is possible.

It flashes when a ribbon cartridge

required for printing is not installed.

SHEET TYPE Key

This selects either roll or piece material

as the loaded medium.

This key can be used only before

material setup.

CARTRIDGE HOLDER

LED

This lights up when a ribbon cartridge is

installed.

It flashes when the cartridge is installed

incorrectly or the ink ribbon has been

used up.

CUT TEST Key

This performs a cutting test (for

verifying that blade force is correct).

This key can be used only after material

setup has been performed.

Part Names and Functions

Set-up and Connections

Do not use with any electrical power

supply that does not meet the

ratings displayed on the unit.

Use with any other power supply may lead

to fire or electrocution.

Ground the unit with the ground

wire.

Failure to do so may result in risk of

electrical shock in the even of a mechanical

problem.

Unpacking, installing, or relocating

the unit are operations which must

be carried out by two or more per-

sons holding the unit at its bottom

surface on the left and right sides.

Failure to do so may

result in dropping

the unit, leading

to injury.

Install in a level and stable location.

Otherwise the unit may tip over and cause

injury.

Do not hold the upper portion of the PC-60 when installing or moving the unit.

Avoid installing the PC-60 in the following conditions, as this may result in damage to the machine.

• Avoid use in locations subject to high levels of electrical noise (near motors, generators, transformers, and

the like).

• Avoid use in locations subject to high humidity or dust.

• The unit becomes hot during use. Do not install in locations where heat radiation is inadequate (i.e., areas

with poor ventilation).

• Do not install in locations subject to strong vibration.

• Do not install in a location exposed to direct sunlight or other strong light.

Always make sure that the main power switch is switched off on both the computer and the PC-60 whenever any

cables are connected or disconnected.

NOTICE

When arranging setup space for the PC-60, make sure you have a space that is at least 1500 mm (59-1/16") wide, 750 mm (29-9/16") in

depth, and 1500 mm (59-1/16") in height. Since the material moves during printing and cutting, make sure the unit is placed on a stable,

sturdy surface. Also make sure there is nothing that can block the material at both front and rear.

Power outlet

Power cord

Power connector

Use only with the power cord

included with this product.

Use with other than the included power cord

may lead to fire or electrocution.

Andere Handbücher für Color Camm Pro PC-60

Inhaltsverzeichnis

Andere Roland Drucker Handbücher

Roland

Roland EGX-400 Bedienungsanleitung

Roland

Roland SolJet PROII SC-540 Bedienungsanleitung

Roland

Roland Texart XT-640 Bedienungsanleitung

Roland

Roland SOLJET PRO4 XF-640 Bedienungsanleitung

Roland

Roland CAMM-2 PNC-2300 Stücklistenhandbuch

Roland

Roland Metaza MPX-90 Bedienungsanleitung

Roland

Roland SOLJET Pro III XC-540 Bedienungsanleitung

Roland

Roland VersaStudio BR-20 Gebrauchs- und Pflegehandbuch

Roland

Roland CAMM-1 PNC-950 Bedienungsanleitung

Roland

Roland EGX-600 Bedienungs- und Wartungshandbuch

Roland

Roland VersaUV LEC2-640 Betriebsanleitung

Roland

Roland SOLJET PROIII XC-540 Bedienungsanleitung

Roland

Roland Metaza MPX-90M Bedienungsanleitung

Roland

Roland iModela iM-01 Gebrauchs- und Pflegehandbuch

Roland

Roland SP-540i Bedienungsanleitung

Roland

Roland VersaUV LEF2-200 Bedienungsanleitung

Roland

Roland AJ-1000 Bedienungsanleitung

Roland

Roland LEC-300 Betriebsanleitung

Roland

Roland TrueVIS SG3-540 Bedienungsanleitung

Roland

Roland GX-640/GX-500/GX-400/GX-300 Bedienungsanleitung

Roland

Roland FJ-42 Bedienungsanleitung

Roland

Roland EU-1000MF Bedienungsanleitung

Roland

Roland SOLJET PROIII DU-740 Bedienungsanleitung

Roland

Roland XC-540W Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung