Roland Soljet EJ-640 Bedienungsanleitung
Setup Guide
Thank you very much for purchasing this product.
To ensure correct and safe usage with a full understanding of this product's performance, please be sure to read through this
manual completely and store it in a safe location.
Unauthorized copying or transferral, in whole or in part, of this manual is prohibited.
The contents of this manual and the specications of this product are subject to change without notice.
This manual and the product have been prepared and tested as much as possible. If you nd any misprints or errors, please
inform Roland DG Corp.
Roland DG Corp. assumes no responsibility for any direct or indirect loss or damage that may occur through use of this product,
regardless of any failure to perform on the part of this product.
Roland DG Corp. assumes no responsibility for any direct or indirect loss or damage that may occur with respect to any article
made using this product.
1
Company names and product names are trademarks or registered trademarks of their respective holders.
http://www.rolanddg.com/
Copyright © 2015 Roland DG Corporation
Contents
Contents........................................................................................................1
1. Installation Environment............................................................................3
Deciding On an Installation Site ................................................................................................. 3
Temperature and Humidity .......................................................................................................... 4
Installation Space ............................................................................................................................. 4
2. Included Items...........................................................................................5
Printer Unit.......................................................................................................................................... 5
Roland Ink System............................................................................................................................ 6
3. About the Symbols ....................................................................................7
4. Assembly and Ink Filling............................................................................8
Checks before Operations............................................................................................................. 8
Step 1: Assembling the Stand...................................................................................................... 9
Step 2: Attaching the Machine ..................................................................................................14
Step 3: Installing the Media Holders........................................................................................15
Step 4: Attaching the DU2-64 Arms.........................................................................................20
Step 5: Installing the Drain Bottle.............................................................................................21
Step 6: Removing the Retainer..................................................................................................23
Step 7: Installing the Roland Ink System................................................................................24
Step 8: Connecting the Cables and Making Initial Settings............................................24
Step 9: Ink Filling.............................................................................................................................28
5. Network Settings .....................................................................................33
Step 1: Make the Network Settings for the Computer......................................................33
Step 2: Make the Network Settings on the Printer.............................................................35
Step 3: Make the Port Settings for the Software RIP..........................................................37
2
3
1. Installation Environment
Deciding On an Installation Site
Install the machine in a quiet, stable location oering good operating conditions. An unsuitable location can
cause accidents, re, faulty operation, or breakdown.
WARNING Install the machine in a location that is level, stable, and able to bear the
weight of the machine.
The total weight of the machine may reach over 325 kg (716.5 lbs). Installa-
tion in an unsuitable location may cause a major accident, including tip over,
fall, or collapse.
WARNING Never install this machine outside or in any location where exposure to
water or high humidity may occur.
Current leakage may cause electrical shock, electrocution, or combustion and
re.
WARNING Never install the machine close to any ammable object or in a gas-lled
location.
Combustion or explosion may occur.
WARNING Install the machine in a clean, brightly lit location.
Working in a location that is dark or cluttered may lead to an accident, such
as becoming caught in the machine as the result of an inadvertent stumble.
WARNING Position the machine so that the power plug is within immediate reach
at all times.
This is to enable quick disconnection of the power plug in the event of an emer-
gency. Install the machine next to an electrical outlet. Also, provide enough
empty space to allow immediate access to the electrical outlet.
CAUTION Ensure adequate ventilation for the work area.
Failing to perform ventilation may result in a health hazard or danger of com-
bustion due to ink fumes.
Unsuitable Installation Sites
Locations subject to large uctuations in temperature or humidity
Locations subject to shaking or vibration
Locations where the oor is tilted, not level, or unstable
Dusty locations
Locations exposed to direct sunlight
Locations near air-conditioning or heating equipment
Locations exposed to water or moving air
Locations exposed to considerable electrical or magnetic noise or other forms of electromagnetic
energy
1. Installation Environment
4
Temperature and Humidity
Maintain the specied temperature and humidity even when the machine is not in use. Failure to do so may
result in malfunction.
Installation Space
The space shown in the gure is required in order to use this machine.
During operation: Temperature 15 to 32°C (59 to 90°F), humidity: 35 to 80%RH (no condensation)
During non-operation: Temperature 5 to 40°C (41 to 104°F), humidity: 20 to 80%RH (no condensation)
4,000 mm (157.5 in.)
1,000 mm (39.4 in.)
3,000 mm (118.1 in.)
Machine space
Work space
2,000 mm (78.7 in.)
5
2. Included Items
The following items are included with the machine. Make sure they are all present before proceeding.
Printer Unit
Power cord(1)
Arms
(1 each for right and left) Casters (2) Stand legs
(1 each for right and left)
Stand stay (1) Shafts (2)
Paper tube
Media holders/ Retaining
screws
(1 each for right and left)
DU2-64 stays (2)
Media holder adjuster Shaft clamps (2) Adjustment papers (2) Media clamps
(1 each for right and left)
Adjustment
bolt (1) Bolts (50) Washers
(black; 8)
Washers
(silver; 8) Bottle stand (1) Drain bottles (2)
Replacement wipers (2) Replacement felt wipers (2) Stand leg xing plates (2) Cable clamp (1)
Tube caps (for 7 colors)* Ink color labels (2) SOL INK cleaning
cartridges (2)
Replacement blades for
separating knife (1)
2. Included Items
6
Cleaning sticks Cleaning liquid (1) Tweezers (1) Pipe (1)
Setup Guide
(this document; 1)
Read this rst (1)
User's Manual (1)
Inkjet printer
maintenance guide (1)
Hexagonal
wrench(1)
Spanner
(1) Software RIP (1)
* Not required when using four colors (cyan, magenta, yellow, and black).
Roland Ink System
Unit (1) LED cover (1) Ink tube cover (top; 1) Subtank guard (1)
Subtank cartridges (8) Lower-right
concealing cover (1) Lower-right stay (1) LED circuit
board stay (1)
Square bushes (4) Y-shaped tubes (8) Screws (M3, black; 12) Screws (M4, silver; 8)
Bushes (2) Multiple color twisted
cable(1) White cable(1) Ink color labels (1)
7
3. About the Symbols
The meanings of the symbols used in this document are as follows.
This symbol indicates instructions that must be followed in relation to opera-
tion. Always follow these instructions to prevent accidents and damage due
to misoperation.
This symbol indicates things that must be checked visually in relation to
operation. Always perform a visual check to prevent accidents and damage
due to failure to check.
8
4. Assembly and Ink Filling
Checks before Operations
CAUTION Unpacking and installation must be carried out by six or more people.
Failure to observe this instruction may cause the machine to fall over, result-
ing in injury.
Completed drawing
Necessary tools
Included items Commercially avail-
able item
Hexagonal wrench Pipe*Spanner Phillips screwdriver
* If the hexagonal wrenches are too small and it is dicult to tighten the bolts, you may need to use the pipe
to increase the length of the wrench.
How to view pictures
When tightening the bolts fully, tighten them securely. Loose bolts may cause the stand to
wobble.
Tighten temporarily Tighten fully
Andere Handbücher für Soljet EJ-640
1
Inhaltsverzeichnis
Andere Roland Drucker Handbücher
Roland
Roland LEC-300A Bedienungsanleitung
Roland
Roland VersaUV LEC2-300 Bedienungsanleitung
Roland
Roland Metaza MPX-90 Bedienungsanleitung
Roland
Roland FJ-500 Bedienungsanleitung
Roland
Roland VS-640 Bedienungsanleitung
Roland
Roland SolJet PROII SC-540 Bedienungsanleitung
Roland
Roland Texart RT-640 Bedienungsanleitung
Roland
Roland versaUV lec-540 Bedienungsanleitung
Roland
Roland Versa UV LEF-12 Bedienungsanleitung
Roland
Roland VS-540i Bedienungsanleitung
Roland
Roland VersaUV LEF2-300 Bedienungsanleitung
Roland
Roland SJ-740 Bedienungsanleitung
Roland
Roland Color CAMM PC-50 Bedienungsanleitung
Roland
Roland VersaCamm SP-300V Bedienungsanleitung
Roland
Roland SJ-740 Bedienungsanleitung
Roland
Roland GR-540 Bedienungsanleitung
Roland
Roland VersaCAMM SP-300S Bedienungsanleitung
Roland
Roland TrueVIS SG-300 Bedienungsanleitung
Roland
Roland VersaUV LEC2-330 Bedienungsanleitung
Roland
Roland VersaSTUDIO Bedienungsanleitung
