Roland VS-640 Bedienungsanleitung

USER'S MANUAL

Thank you very much for purchasing this product.

To ensure correct and safe usage with a full understanding of this product's performance, please be sure to read through

this manual completely and store it in a safe location.

Unauthorized copying or transferral, in whole or in part, of this manual is prohibited.

The contents of this document and the specications of this product are subject to change without notice.

The documentation and the product have been prepared and tested as much as possible. If you nd any misprint or

error, please inform us.

Roland DG Corp. assumes no responsibility for any direct or indirect loss or damage which may occur through use of this

product, regardless of any failure to perform on the part of this product.

Roland DG Corp. assumes no responsibility for any direct or indirect loss or damage which may occur with respect to

any article made using this product.

Contents

http://www.rolanddg.com/

Company names and product names are trademarks or registered trademarks of their respective holders.

Chapter 7 Main Specications......................................................................................161

Printing/Cutting Area ................................................................................................162

Maximum Area................................................................................................................................................... 162

Maximum Area When Using Crop Marks.................................................................................................. 162

The Media-cuto Location During Continuous Printing .................................................................... 163

About the Blade........................................................................................................164

Locations of the Power Rating and Serial Number Labels.......................................165

Specications ...........................................................................................................166

This document is the Use's Manual for four models: VS-640/540/420/300. This document uses the following

notation to distinguish between the four models where necessary.

VS-640 — 64-inch model

VS-540 — 54-inch model

VS-420 — 42-inch model

VS-300 — 30-inch model

Also, most of the gures in this document depict the VS-640

To Ensure Safe Use

This machine weighs 200 kg (441 lb.). Media weighs 40 kg (88 lb.).

Danger of re, burns, or toxic gas emissions

WARNING

Install the machine in a location that is

level, stable, and able to bear the weight

of the machine.

The total weight may reach over 200 kg

(441lb.) for the 64-inch model (, 170kg

(375lb.) for the 54-inch model, 150 kg

(331lb.) for the 42-inch model, and 130

kg (287lb.) for the 30-inch model). Instal-

lation in an unsuitable location may cause

a major accident, including tip over, fall, or

collapse.

Unloading and emplacement are opera-

tions that must be performed by 6 per-

sons or more (, by 4 persons or more for

the 30-inch model).

Tasks that require undue effort when per-

formed by a small number of persons may

result in physical injury. Also, if dropped,

such items may cause injury.

WARNING

Be sure to lock the stand's casters.

If the machine should begin to topple, a ma-

jor accident may result, including crushing

of the appendages or the body.

When storing roll media, implement

adequate safety measures to ensure

that the stored media will not roll, fall, or

topple over.

Danger exists of becoming pinned under the

media and suffering serious injury.

Handling roll media is an operation that

must be performed by two persons or

more, and care must be taken to prevent

falls.

Attempting to lift heavy media in a manner

that taxes your strength may cause physi-

cal injury.

WARNING

Caution: high temperatures

Areas such as the dryer become hot. Exer-

cise caution to avoid re or burns.

When printing is not being performed,

remove any loaded media or switch off

the power.

The continued application of heat at a

single location may cause the release of

toxic gases from the media or pose a re

hazard.

WARNING

Never use media that cannot withstand

heat.

Doing so may degrade the media, or may

result in re or the release of toxic gases.

Machine

Highlights

Pour utiliser en toute sécurité

Le poids de cet appareil est de 200 kg (441 lb.)

Le poids du support est de 40 kg (88 lb.)

ATTENTION

Installer l'appareil à un endroit stable et

plat et capable de supporter son poids.

Le poids total de l’appareil peut être de

200 kg (441 lb.) ou plus pour le modèle de

64 pouces (170 kg (375 lb.) ou plus pour

le modèle de 54 pouces, 150 kg (331 lb.)

ou plus pour le modèle de 42 pouces,130

kg (287 lb.) ou plus pour le modèle de 30

pouces). Installer l'appareil à un endroit

inapproprié peut provoquer un accident

grave comme le renversement, la chute ou

l'écrasement.

Le déchargement et la mise en place

doivent être faits par au moins 6 per-

sonnes on plus (, 4 personnes ou plus

pour le modèle de 30 pouces).

Les tâches qui exigent un effort trop grand

si elles sont exécutées par un petit nombre

de personnes peuvent être cause de bles-

sures. La chute d'articles très lourds peut

aussi causer des blessures.

ATTENTION

S'assurer de verrouiller les roulettes de

la base.

Si l'appareil devait commencer à basculer, il

s'ensuivrait un accident grave, par exemple

l'écrasement de membres ou du corps.

Prendre les mesures de sécurité adé-

quates pour l'entreposage des rouleaux

de support pour s'assurer qu'ils ne

rouleront pas, ne tomberont pas et ne

se renverseront pas.

Il y a risque d'être écrasé par le support et

de subir des blessures graves.

La manutention du support en rouleau

doit être faite par deux personnes ou

plus et il faut prendre des précautions

pour éviter les chutes.

Tenter de soulever des objets trop lourds

peut causer des blessures.

Risque d'incendie, de brûlures ou d'émissions de gaz toxiq

ATTENTION

Attention : températures élevées.

Les zones comme le séchoir chauffent.

Faire preuve de prudence pour éviter un

incendie ou des brûlures.

Quand aucun travail d'impression n'est

en cours, retirer tout support de l'appareil

ou couper l'alimentation électrique.

L'application continue de chaleur à un point

unique peut causer l'émission de gaz tox-

iques ou créer un risque d'incendie.

ATTENTION

Ne jamais utiliser un support qui ne peut

pas supporter la chaleur.

L'utilisation d'un support qui ne supporte pas

la chaleur peut détériorer le support, créer

un risque d'incendie ou causer l'émission

de gaz toxiques.

Machine

Highlights

Prepare the Media

Basic

Operation

Usable Media

This machine cannot necessarily print every kind of media. When selecting media, be sure to carry out testing

in advance to make sure that satisfactory printing quality is obtained.

Size

Width (For both Roll Media and sheet media)

64-inch model: 210 to 1625 mm (8.3 to 64 inches)

54-inch model: 210 to 1371 mm (8.3 to 54 inches)

42-inch model: 210 to 1071 mm (8.3 to 42 inches)

30-inch model: 210 to 762 mm (8.3 to 30 inches)

A) Cuttable media thickness (For both Roll Media and sheet media)

0.08 mm to 0.22 mm (0.3 to 1 mil) (depending on media composition)

B) Maximum media thickness (For both Roll Media and sheet media)

Printing only:1.0 mm (4mil)

When performing cutting: 0.4 mm (1.6 mil)

Roll outer diameter

210 mm (8.2 inches)

Paper tube (core) inner diameter

76.2 mm (3 inches) or 50.8 mm (2inches)

Note: To use 2 inches media, the optional media anges are required. For information about optional items,

contact your authorized dealer or us.

Roll weight

64-inch model: 40 kg (88 lb.)

54-inch model: 30 kg (66 lb.)

42-inch model: 25 kg (55 lb.)

30-inch model: 25 kg (55 lb.)

Note: When using the take-up unit, conditions are dependent on the usable media of the take-up unit.

Other conditions

Media such as the following cannot be used.

Media whose end is attached to the paper tube (core)

Media which is severely warped or which has a strong tendency to reroll

Media that cannot withstand the heat of the media heating system

Media whose paper tube (core) is bent or crushed

Media that bends under its own weight when loaded

Media on a sagging roll

Media that is rolled unevenly

Basic

Operation

Loading Media

Loading Roll Media

CAUTION Load roll media correctly.

Otherwise the media may fall and cause injury.

CAUTION Roll media weighs about 40 kg (88 lb.). To avoid injury, handle with

care.

CAUTION Never load media that weighs over 40 kg (88lb.) for the 64-inch model (,

30 kg (66lb.) for the 54-inch model, and 25 kg (55lb.) for the 42-inch or the

30-inch model).

The machine may fail to withstand the weight and tip over or cause the media

to fall.

Install the media to the media holder.

Note: The media holder of this machine is exclusive use for the media of paper tube (core) inner diameter

3 inches. To use 2 inches media, the optional media anges are required. For information about optional

items, contact your authorized dealer or us.



Open the front cover.

Move the media clamps to the left and right ends respectively.



Loosen the retaining screws of the media holders.

Move the media holders all the way to the left and right.

Front cover

Media clamp

Maintenance

Replacing Consumable Parts

Replacing the Wiper

The wiper is a component that you use when cleaning the print head. When the screen displays a message

like the one shown, it means the item needs to be replaced. Replace with new items.

Regarding the purchase of the wiper, contact your authorized Roland DG Corp. dealer.

CAUTION Be sure to perform operations as specied by the following instructions,

and never touch any area not specied in the instructions.

Sudden movement of the machine may cause injury.

Display the [REPLACE WIPER] menu.



When the message shown in the gure appears, press .



Remove any media from the platen.



Press .



Press several times until the screen shown on the left

appears.

Press , and then .



Press , and then .



Press .

The print-head carriage moves to a location where wiper replacement is

possible, and then the screen shown in the gure appears.



Remove the cover R.

TIME FOR

WIPER REPLACE

TIME FOR

WIPER REPLACE

SUB MENU

MAINTENANCE

REPLACE WIPER

OPEN COVER R

Screw

Cover R

Hook

162

Main

Specications

Printing/Cutting Area

Maximum Area

The printing or cutting area along the horizontal plane (the direction in which the carriages move) is deter-

mined by the position of the pinch rollers.

Maximum Area When Using Crop Marks

When crop marks are used, the printing or cutting area is reduced from the maximum area by an amount

equal to the crop marks.

10 mm

12.5 mm

10 mm

12.5 mm

10 mm

12.5 mm

10 mm

Crop mark

Maximum area

Printing or cutting area

10 mm 1.5 mm

Max. 24,998 mm

1.5 mm 10 mm

90 mm

75 mm

Printing or cutting area

Max. 1,600 mm (64-inch model)

Max. 1,364 mm (54-inch model)

Max. 1,064 mm (42-inch model)

Max. 736 mm (30-inch model)

Printing or cutting coordinates origin (0,0)

Pinch roller

Specications

Main

Specications

167

Note: The media holder of this machine is exclusive use for the media of paper tube (core) inner diameter 3 inches. To use 2 inches media, the optional

media ﬂanges are required.

The length of printing or cutting is subject to the limitations of the program.

Media type: Media speciﬁed by Roland DG Corp. (Cutting only)

Temperature: 25°C (77°F), humidity: 50%

Roll media must be loaded correctly.

Applicable when all pinch rollers available to the media width are used.

Side margins: 25 mm or more for both the left and right margins

Front margin: 35 mm or more

Excluding expansion/contraction of the media

Not assured when the print heater or dryer is used.

All correction or adjustment function of this machine has been made properly.

With Roland PET ﬁlm, print travel: 1 m

[PREFEED] menu item must be set to "ENABLE."

Range for assured repetition accuracy

64-inch model

For media with a width exceeding 610 mm: Length 4,000 mm

For media with a width of 610 mm or less: Length 8,000 mm

54-inch model

For media with a width exceeding 610 mm: Length 4,000 mm

For media with a width of 610 mm or less: Length 8,000 mm

42-inch model

Length 3,000 mm

30-inch model

Length 3,000 mm

Provided that media length is under 3,000 mm

Excludes the eﬀects of slanted movement and of expansion and contraction of the media.

Data size:

64-inch model:1,000 mm in the media-feed direction, 1,600 mm in the carriage-movement direction

54-inch model:1,000 mm in the media-feed direction, 1,600 mm in the carriage-movement direction

42-inch model:1,000 mm in the media-feed direction, 1,346 mm in the carriage-movement direction

30-inch model:1,000 mm in the media-feed direction, 736 mm in the carriage-movement direction

No lamination

Automatic detection of crop marks at 4 points when media is reloaded.

During cutting, [PREFEED] menu item must be set to "ENABLE."

Excluding possible shift caused by expansion/contraction of the media and/or by reloading the media.

Warm-up is required after power up. This may require 5 to 20 minutes, depending on the operating environment.

Depending on the ambient temperature and media width, the preset temperature may fail to be reached.

Operating environment

Use in an operating envi-

ronment with this range.

R2-100701

This product is using GNU General Public License (GPL) / GNU Lesser General Public License (LGPL) software. You have the

right to acquire, modify, and distribute the source code for this GPL/LGPL software.You can obtain the GPL/LGPL source code

used in this product by downloading it from the following website.

URL: http://www.rolanddg.com/gpl/

RolandDG Corp. has licensed the MMP technology from the TPL Group.

Andere Handbücher für VS-640

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Roland Drucker Handbücher

Roland

Roland TrueVIS VG3-640 Bedienungsanleitung

Roland

Roland TrueVIS SG-300 Bedienungsanleitung

Roland

Roland Metaza MPX-90M Bedienungsanleitung

Roland

Roland VersaUV LEF-20 Gebrauchs- und Pflegehandbuch

Roland

Roland TrueVIS VG2-640 Bedienungsanleitung

Roland

Roland VersaStudio BN-20 Bedienungsanleitung

Roland

Roland LEC-300 Bedienungsanleitung

Roland

Roland SolJet PROII SC-540 Bedienungsanleitung

Roland

Roland Texart RT-640 Bedienungsanleitung

Roland

Roland VersaCamm SP-540V Bedienungs- und Wartungshandbuch

Roland

Roland VersaSTUDIO BN-20D Bedienungsanleitung

Roland

Roland VersaStudio BT-12 Bedienungsanleitung

Roland

Roland VersaCamm VP-540i Bedienungsanleitung

Roland

Roland XC-540W Bedienungsanleitung

Roland

Roland TrueVIS MG-640 Bedienungsanleitung

Roland

Roland TrueVIS SG2-640 Bedienungs- und Wartungshandbuch

Roland

Roland VersaArt RE-640 Bedienungsanleitung

Roland

Roland VersaUV LEF2-200 Bedienungsanleitung

Roland

Roland Soljet Pro III XJ-540 Bedienungs- und Wartungshandbuch

Roland

Roland SOLJET PROIII XC-540 Bedienungsanleitung

Roland

Roland SOLJET PROIII XC-540 Bedienungsanleitung

Roland

Roland SJ-740 Bedienungsanleitung

Roland

Roland CAMM-2 PNC-2300 Stücklistenhandbuch

Roland

Roland iModela iM-01 Gebrauchs- und Pflegehandbuch

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung