Roland MKS-80 Bedienungsanleitung

^Roland

MMSM SOUND MODULE

SUPER JUPITER

MIKm CZID

Owner's Manual

RADIO AND TELEVISION INTERFERENCE

"Warning -This equipment has been verified to comply with the limits for aClass Bcomputing

device, pursuant to Subpart J, of Part 15, of FCC rules. Operation with non-certified or non-verified

equipment is likely to result in interference to radio and TV reception."

The equipment described in this manual generates and uses radio-frequency energy. If it is not

installed and used properly, that is, in strict accordance with our instructions, it may cause interference

with radio and television reception.

This equipment has been tested and found to comply with the limits for aClass Bcomputing device

in accordance with the specifications in Subpart J, of Part 15, of FCC Rules. These rules are designed

to provide reasonable protection against such ainterference in aresidential installation.

However, there is no guarantee that the interference will not occur in aparticular instaliation. If this

equipment does cause interference to radio or television reception, which can be determined by

turning the equipment on and off, the user is encouraged to try to correct the interference by the

following measure:

•Disconnect other devices and their input/output cables one at atime. If the interference stops, it

is caused by either the other device or its I/O cable.

These devices usually require Roland designated shielded I/O cables. For Roland devices, you can

obtain the proper shielded cable from your dealer. For non Roland devices, contact the manufacturer

or dealer for assistance.

If your equipment does cause interference to radio or television reception, you can try to correct

the interference by using one or more of the following measures;

•Turn the TV or radio antenna until the interference stops.

•Move the equipment to one side or the other of the TV or radio.

•Move the equipment farther away from the TV or radio.

•Plug the equipment Into an outlet that is on adifferent circuit than the TV or radio. (That Is, make

certain the equipment and the radio or television set are on circuits controlled by different circuit

breakers or fuses.)

•Consider installing arooftoptelevision antenna with coaxial cable lead-in between the antenna and

TV.

If necessary, you should consult your dealer or an experienced radio/television technician for

additional suggestions. You may find helpful the following booklet prepared by the Federal Communi-

cations Commission;

"How to identify and Resolve Radio-TV Interference Problems"

This booklet Is available from the U.S. Government Printing Office, Washington, D. C, 20402,

Stock No.004-a00-00345-4.

Tl PANEL DESCRIPTION

^Receive Made indicator

©CantrasT Knob

Memory Area Switch

^Memory Cartridge Holder

MIDI Massage indicator

©Power Switch

M(D1 Channel Selector Switch

'Protect Switch

S/L Mode Switch

©MIDI Function SiMitcn

ODynamics Sens Knob

©Volurne Knob

WHMMC

NJ\S ttSM

bD D

@Progrsrnmer Connector

10 Input Selector Switch

MIDI Connector

ITHRU/OUT/IN)

-J

"S"

Output Connector

<XLR)IUPPER/ LOWER)

Output Mode Switch

@Output Jack il/A Standard)

lUPPER/LOWERi

©Output Level Seiector Switch

The MKS-SO is an 8voice, 16 VCO polyphonic syn-

thesizer module that can be played by MIDI music

messages sent from the other MIDI device.

FEATURES

•The MKS-80 has memory capacity that retains

64 different tone coiors. By using the Memory

Cartridge M-64C that retains up to 128 tone

colors, total of 192 patch programs can be

available.

•The MKS-80 features battery backup system

that retains the data in memory even when

switched off.

•Auto Tune function that allows ail VCO's to be

instantaneously tuned just by pressing abutton.

•Patch Preset is aprogram that can contain atone

color (or even apair of tone colors depending on

the Key mode setting) and various mode and

effect settings.

•The Octave Shift function allows shifting the

pitch of the entire keyboard without changing

the VCO range.

•Data in the MKS-80's memory can be transferred

to another MKS-80 or to acomputer.

•The MKS-BO's dynamics function can change The

attack time as weli as the level.

•8y the unique Envelope Reset function, each

time you press anew key, the note wiH start

from the beginning of the envelope curve.

•By using the optionai Programmer MPG-80, syn-

thesizing will become much easier.

The Detune function enables apowerful ensemble

effect in Unison mode.

It is important to understand ail the functions

of the MKS-BO to make the best use of it.

Please read the separate volume "MIDI" and

this owner's manual.

CONTENTS

[fj Panel Description 3

A. Front Panel 3

B. Rear Panel 3

l2j Connection 6

J3] Operation 7

A. Outline of the IVIKS-80 7

B. Play Mode 8

a. MIDI Channel Setting 8

b. MIDI Function Switch 8

c. Tone Color Selection 9

1) Calling aPatch Preset 10

2) Calling aTone Memory 10

d. Auto Tune 13

e. Volume 13

f. Dynamics Sens Knob 13

g. Contrast Knob 13

C. Edit Mode (I) 14-20

a. Parameters of Tone Memory Section ... 14

b. Editing aTone Memory 21

c. Parameters of Patch Preset Section . . .22—25

d. Editing aPatch Preset 26

D. EditlVIode (II) 27

a. Setting up the Programmer MPG-80 .... 27

1) Programmer Connector 27

2) Connection 27

b. How to use the Programmer MPG-BO ... 28

1)Method 128

2! Method 229

E. Write Mode 30

a. Writing aTone Memory 30

b. Writing aPatch Preset 31

F. Memory Cartridge 32

a. Saving onto the Memory Cartridge 32

b. Loading from the Memory Cartridge ... 34

g] MIDI 36

A. Saving and Loading 36

a. Saving the data in the MKS-BO

to aMIDI device (or computer} 37

b. Loading the data in the MIDI device

(or computer) to the MKS-80 39

B. Indicators 40

a. Receive Mode Indicators 40

b. MIDI Message indicators 40

[5] Tables 41

Edit Map 11

Parameter Table 41

Display Message Table 44

Program Change Table 45

MIDI Function Table 46

\6\ Specifications 47

IMPORTANT NOTES

Before turning the MKS-80 on, make sure that

the Protect Switch ®is set to the ON position.

Otherwise the data in memory may be destroyed.

Power Supply Location

•The appropriate voltage to be used is shown on

the name piate on the rear panel. Be sure that it

meets the voltage system in your country.

•Do not use the same socket that is used for any

noise generating device, such as a motor, or varia-

ble lighting system.

•When setting up the MKS-80, be sure that all the

units are turned off.

•This unit might not work properly if turned on

immediately after turned off, or if the power

cable is plugged in with the unit turned on. If

this happens, simply turn the unit off, and turn it

on again in afew seconds.

•Operating the MKS-80 near aneon or fluorescent

lamp may cause noise interference. If so, change

the angle or position of the MKS-80.

•Avoid using the MKS-80 in extreme heat or

humidity or where it may be affected by dust.

Cleaning

•Use asoft cloth and clean on!y with amild

detergent.

•Do not use solvent-such as paint thinner.

•This unit might get hot while operating, but

there is nothing to worry about.

2l CONNECTION

LOWER UPPER

si- C3 CD

CD CZ!

»-'

,,-, 1

'-— -—

en Cj CD CZl CD CD [li Ci

CD Cpip CpZZ! rp :^^J--

MID! IN

MIDI OUT

allllllllllllllllllllllllllllllliill

MPG-80 o

PDOCHlUUra

MID! IN MIDI OUT

fc^:^ t.;:?:i

Ampliflbr

MKB- 1000

JP-6

JUNO-105

MSQ700

MSO-!0C^etc

Amplifier

When the MKS-80 is used in monaural.set the Out-

put Mode Switch Qto the M\x position. \i it is set

to the U/L position, the MKS-80 may not sound at

all.

*Before setting up the units, mal<e sure that all the

units are turned off and the volume of the ampli-

fier is set to zero.

Input Selector Switch Q

This selects whether to receive the MIDI message

from the MIDI IN Jack or the Programmer Con-

nector. When not using the Programmer, set It to

the MIDI position, if it is set to the Programmer

position, the message received from the MIDI IN

will be ignored.

3] OPERATION

A. OUTLINE OF THE MKS-SO

The MKS-80 is apolyphonic syntiiesizer module

that can be played by the MIDI music messages sent

from the external device.

If the MKS-80 is properly set up with adevice

transmitting MIDI music messages, it will be ready

to be played by powered on. There are 64 tone

colors (we call them Tone Memories) and 64 com-

bination programs of atone color (or apair of tone

colors) and various effect and mode settings (we call

them Patch Presets) preprogrammed in the MKS-80's

memory which can be recalled to be used just by

pressing buttons.

Also, these Tone Memories and Patch Presets can be

edited as you like. This editing operation, however,

does not automatically rewrite the existing tone

color. If you wish to write the edited tone color,

appropriate writing operation is required.

MEMORY CARTRIDGE

CD POLV

r~i MONO

MIDI AHEA MTCH MODE LOWER UPPER

CZ! t^

ini

[^ ID^

-INT

MIDI CHANNEL

MEMORY CARTRIDQE MfDI MESSAGE

0fr9-

puepy^j

Protect Switch

The supplied Memory Cartridge M-64C can be effec-

tively used to expand the memory capacity. The

M-64C has two separate blocks Aand B, and can

retain 64 different Tone Memories and Patch Presets

in each block. The cartridge memory can be used

exactly like the internal memory of the MKS-80.

You may consider it as a part of internal memory.

Be sure that the Protect Switch on the Cartridge Is

set to the ON position when connecting it to the

MKS-80 or disconnecting, otherwise the data in

memory might be damaged. Securely insert the

Cartridge to the Cartridge Holder ®of the MKS-

80 with its Protect Switch facing upward.

*To prevent accidental loss of the data, set the

Protect Switch to the ON position except for

when writing new data.

*Refer to Patch Preset and Tone Memory on page

B. PLAY MODE

Make sure that all the connections have been cor-

rectly made, and turn on the MKS-80,then the key-

board, and finally the amplifier. Now, the MKS-80's

Display Window shows AUTO TUNE, all the 16

VCO's being automatically tuned. And soon, the

Display will respond as shown right.

At this stage, if the MKS-80 receives the message on

the same MIDI Channel as shown at "a" in the Dis-

play, it will operate. While the MKS-80 is receiving

any message, the MIDI Message Indicator is lighted.

If the message is transmitted on adifferent channel,

the MKS-80 cannot receive the message, therefore,

the indicator stays dark.

The leners "a" to "f" represent the following

elemenis.

aMIDI Channel

bMemory Area

I-Interna! Memory (INT)

A-Memory Canridge (A)

B-Memory Cartridge (Bl

cPatch Number

dKey Mode

W-. Whole

S2- Split 2

SI -Split 1

D-Dual

eLower Tone Number

fUpper Tone Number

a. MIDI Channel Setting

©Press the MID! Channel Button ®,and the dis-

play will respond as shown right.

(2) While holding the MIDI Channel Button ,

assign the MID! Channel by pressing aBank But-

ton (E) and aNumber Button ®.The Display

shows the selected MIDI Channel in blue num-

bers.

*DD represent the MIDI Channel currently

remembered in memory.

*The set MID! Channel is remembered even after

power off, so the next time the MKS-80 is

powered on, the previous MIDI Channel remains.

b. MIDI Function Switch

With this switch, you can select which of the MIDI

function to be used.

To prevent improper operation, select either the

Ior II position. The HI position is to be selected

only for aspecial purpose (Exciusive Message).

*For the details of the

refer to page 46.

IDI Function Switch,

c. Tone Color Selection

Tone Memory and Patch Preset

There are two types of patch programs in the

l\^KS-80's memory.

One is called Tone Memory which is atone color

with various parameter settings of such as VCO,

VCF, VGA, ENV sections. Up to 64 different Tone

Memories can be retained in memory and each Tone

Memory has its own number from 1 1 to SB (we call

it Tone Number).

Number

Bank t'J "^ J5 h 7P

Another is called Patch Preset which is acombina-

tion of aTone Number or apair of Tone Numbers

and various settings of effects and modes. APatch

Preset can only remember the combination of the

Tone Numberls} and effect and mode settings, that

is, it has no ability of retaining the tone color itself.

Therefore, if the Tone Memory is edited or replaced

with anew tone color, the Patch Preset will accord-

ingly altered. Up to 64 Patch Presets cah be stored

in memory, and each Patch Preset has anumber

from nto 88 (we call it Patch Number),

*To assign aTone Number or Patch Number,

simply press the relevant Bank and Number

Buttons.

e.g.) Press the Bank Button (.1) and the Number

Button.:6;to select Program 56.

is program 56.

«MEMORY AREA

Depending on the position of the Memory Area

Switch ®,available memory area will change as

shown beiow.

INT- Internal memory of the MKS-80

A-Memory Cartridge Block A

B—Memory Cartridge Block B

*At power up, Patch Preset 1 1 in the selected

memory area is automatically recalled. If, how-

ever, the Memory Cartridge is not connected.

Patch Number 11 in the Internal memory will

be called.

1} Calling aPatch Preset

Any Patch Preset can be recalled in the Play mode.

®Set the Memory Area Switch ®to the desired

position.

®,assign the Patch Preset you wish to recall.

2) Calling aTone Memory

You cannot change Tone Memories in the Play

mode. Turn the MKS-80 to the Edit mode.

(D Set the Memory Area Switch @to the desired

position.

(2) Press the Tone Button <D .

Q) By using aBank Button (£) and aNumber Button

®,assign the Tone Memory you wish to recall.

*To turn the MKS-BO to the Play mode, just press

the Tone Button (ff again.

*If you try to call aTone Memory in the Cartridge

without the Cartridge connected to the MKS-80,

the Display will respond as shown below.

Cont, to p. 13

Andere Handbücher für MKS-80

Andere Roland Aufnahmegeräte Handbücher

Roland

Roland SN-700 Bedienungsanleitung

Roland

Roland RA-90 Bedienungsanleitung

Roland

Roland JV-1080 Bedienungsanleitung

Roland

Roland EV-1-WL Bedienungsanleitung

Roland

Roland SR-20HD Bedienungsanleitung

Roland

Roland V-160HD RCS Bedienungsanleitung

Roland

Roland Sonar V-Studio 100 Bedienungsanleitung

Roland

Roland TR-08 Bedienungsanleitung

Roland

Roland AR-3000SD Installationshandbuch

Roland

Roland CM-500 Bedienungsanleitung

Roland

Roland VP-03 Bedienungsanleitung

Roland

Roland TR-707 Bedienungsanleitung

Roland

Roland P-20HD Bedienungsanleitung

Roland

Roland R-07 Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Roland

Roland A-80 Bedienungs- und Wartungshandbuch

Roland

Roland MC-50 mkII Bedienungsanleitung

Roland

Roland AR-100 Bedienungsanleitung

Roland

Roland S-770 Bedienungsanleitung

Roland

Roland TR-909 Bedienungsanleitung

Roland

Roland Soun Canvas P-55 Bedienungsanleitung

Roland

Roland CD-2i Bedienungsanleitung

Roland

Roland CD-2e Technisches Datenblatt

Roland

Roland SP-404 Bedienungs- und Wartungshandbuch

Beliebte Aufnahmegeräte Handbücher anderer Marken

KV2 Audio

KV2 Audio 500 Series Bedienungsanleitung

Robotics Technologies

Robotics Technologies microBus-Cam II Bedienungsanleitung

Seca

Seca 460 Bedienungsanleitung

Cognex

Cognex MVS-8000 Series Bedienungsanleitung

Mect

Mect MPNC006 Series Bedienungsanleitung

Bad Caf

Bad Caf THE LEASH Bedienungsanleitung

Strymon

Strymon NIGHTSKY Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung

Tews Technologies

Tews Technologies TPMC465 Bedienungsanleitung

Honeywell

Honeywell Excel 50 Bedienungsanleitung

SeaLevel

SeaLevel COMM+8.LPCI Bedienungsanleitung

Arturia

Arturia AUDIOFUSE STUDIO Bedienungsanleitung

Rukra

Rukra RK-1240 Bedienungsanleitung

Samson

Samson SCOM Bedienungsanleitung

Dynacord

Dynacord DPS260 Bedienungsanleitung

Pyle Pro

Pyle Pro PSS8 Bedienungsanleitung

Nice

Nice Core Bedienungsanleitung

RF-System

RF-System TinyGate Gebrauchs- und Pflegehandbuch