Rosewill RNX-N150NUBv2 Bedienungsanleitung

User Manual

RNX-N150NUBv2

Wireless N150 Nano USB Adapter

FCC RF Radiation Exposure Statement:

Specifications are subject to change without notice. is a registered

trademark of Rosewill, Inc. Other brands and product names are trademarks or

registered trademarks of their respective holders.

No part of the specifications may be reproduced in any form or by any means or

used to make any derivative such as translation, transformation, or adaptation

reserved. www.rosewill.com

This equipment complies with FCC radiation exposure limits set forth for

an uncontrolled environment. End users must follow the specific operating

instructions for satisfying RF exposure compliance. This transmitter must not be

co-located or operating in conjunction with any other antenna or transmitter. This

equipment has been SAR-evaluated for use in hand. SAR measurements are

based on 5 mm spacing from the body and that compliance is achieved at that

distance.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates and uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio / TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received, including interference that

may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

Note:

The manufacturer is not responsible for any radio or TV interference caused by

unauthorized modifications to this equipment. Such modifications could void the

user’s authority to operate the equipment.

SECTION 1: Introduction

1.1 Product Features…………………………………….…............ 05

1.2 Package Contents………………………………….........…...... 05

1.3 LED Status…………………………………….......................... 05

1.4 Specifications………....................…………...…….…............ 06

SECTION 2: Quick Installation Guide

2.1 Hardware Installation…………………......................….......... 07

2.2 Software Installation……………............................................ 07

SECTION 3: Connect to a Wireless Network

3.1 In Windows XP………………………...................................... 10

3.2 In Windows 7………………………………………................... 11

3.3 In Windows 8.1…………………………….............................. 11

3.4 In Windows 10………………................................................. 13

SECTION 4: Client Utility

4.1 Connection Profile Management………………….................. 14

4.1.1 Add New Profile……………………............................... 15

4.1.2 Remove Existing Profile…………………….................. 17

4.1.3 Edit Existing Profile………………………….................. 17

4.1.4 Make a Copy of Existing Profile…………..................... 18

4.1.5 Set Default Profile………………................................... 18

4.2 View General Information and Network Status………........... 19

4.2.1 General Information……………………......................... 19

4.2.2 Status……………………............................................... 19

4.3 Miscellaneous Settings…………………………...................... 20

4.4 Establish Secure Connection with AP by WPS…………....... 21

SECTION 5: Soft-AP Function

5.1 Switch to AP Mode and Station Mode………………….......... 23

5.1.1 Configure SSID and Channel…………………….......... 24

5.1.2 Set Up Soft-AP Security………………………............... 25

5.2 Advanced Settings……………………………......................... 26

5.3 Wireless Statistics………………............................................ 27

Appendix: Troubleshooting

Table of Contents

Wireless N150 Nano USB Adapter User Manual

RNX-N150NUBv2

SECTION 1: Introduction

1.1 Product Features

• Complies with IEEE 802.11n, IEEE 802.11g and IEEE 802.11b standards

• Supports USB 2.0 interface

• Provides 150 Mbps receiving rate and 150 Mbps sending rate

• Auto-detect and switch the network transmission rate

• Provides two working modes: Infrastructure and Ad Hoc mode

• Supports 64/128-bit WEP Encryption, WPA, WPA-PSK, WPA2, WPA2-PSK,

TKIP/AES security authentication standards

• Supports WPS (Wi-Fi Protected Setup) encryption method to simplify setup

and operation

• Easy-to-install

• Supports Windows 7/8/8.1/10 (32/64-bit), Linux, Mac OS X 10.4-10.11

Rosewill RNX-N150NUBv2 connects your laptop or desktop to a wireless

network to enjoy fast, reliable wireless connectivity. The nano-size design

makes the adapter convenient and, once connected to a USB port, can be

left there. It’s your number one choice for enjoying fast, reliable wireless

networking.

1.2 Package contents

• 1x RNX-N150NUBv2 Wireless N150 Nano USB Adapter

• 1 x Resource CD (drivers, utility and user manual)

• 1 x Quick Installation Guide

1.3 LED Status

Status Working Status

On • The adapter has been installed.

• Data is being transmitted or received at a high data rate.

Off The adapter has been removed or not detected.

Wireless N150 Nano USB Adapter User Manual

RNX-N150NUBv2

Normal

Interface High Speed USB 2.0 Interface

Standards IEEE 802.11n; IEEE 802.11g; IEEE 802.11b

Frequency Band 2.4 GHz ISM (Industrial Scientific Medical) Band

Radio Data Rate

802.11b: 11/5.5/2/1 Mbps Auto Fallback

802.11g: 54/48/36/24/18/12/9/6 Mbps Auto Fallback

802.11n: up to 150 Mbps (Downlink) and 150 Mbps (Uplink)

Modulation

11b: DQPSK, DBPSK, DSSS, CCK

11g: BPSK, QPSK, 16QAM, 64QAM, OFDM

11n: BPSK, QPSK, 16QAM, 64QAM with OFDM

Media Access

Protocol CSMA/CA with ACK

Data Security 64/128-bit WEP Encryption

WPA, WPA-PSK, WPA2, WPA2-PSK, TKIP/AES

Frequency* 2412 - 2462 MHz (North America)

2412 - 2472 MHz (Europe)

Radio Channel* 1 to 14 channels (Universal Domain Selection)

Operating System Windows 7/8/8.1/10 (32/64-bit), Linux, Mac OS X 10.4-10.11

Certifications FCC, CE

* Only 2.412 GHz-2.462 GHz is allowed to be used in the USA, which means only channels 1-11 are available for American users to

choose.

1.4 Specifications

Environmental and Physical

Working Temperature 0˚C to 40˚C (32˚F to 104˚F)

Storage Temperature -20˚C to 75˚C (-4˚F to 167˚F)

Working Humidity 10% to 90% RH, Non-Condensing

Storage Humidity 5% to 90% RH, Non-Condensing

Wireless N150 Nano USB Adapter User Manual

RNX-N150NUBv2

SECTION 2: Quick Installation Guide

Please install the adapter into your computer before installing the driver from

the Resource CD.

2.1 Hardware Installation

2.1 Software Installation

Insert the wireless USB adapter into an empty USB 2.0 port of your computer

when it is switched on.

Note: When the adapter has been successfully installed on your computer, you

may be prompted by the Found New Hardware Wizard (Figure 2-1). Please

click “Close” and follow the software installation steps to install the driver and

utility for your computer.

Figure 2-1 New Hardware Wizard found in Windows 7

Figure 2-2 AutoRun Window

Insert the resource CD into your CD-ROM drive. An AutoRun window will pop

up (Figure 2-2). Click the “Driver Installation” button to start the installation

procedure. If AutoRun does not work, browse the Resource CD, open the folder

and double-click “Setup.exe” to begin.

Wireless N150 Nano USB Adapter User Manual

RNX-N150NUBv2

The InstallShield Wizard will pop up (Figure 2-3) and start installing the driver

automatically. This process may take 1-3 minutes. Do not click the “Cancel”

button, otherwise the installation will stop.

Figure 2-3

Figure 2-4

Wireless N150 Nano USB Adapter User Manual

RNX-N150NUBv2

After the driver and utility are installed successfully, you must reboot your

computer. Select “Yes, I want to restart my computer now.”, then Click “Finish”.

After restarting the computer, the Wi-Fi icon will appear at the lower-right

side in your system tray. To connect to a network, please refer to Section 3:

Connect to a Wireless Network.

Figure 2-5

Wireless N150 Nano USB Adapter User Manual

RNX-N150NUBv2

SECTION 3: Connect to a Wireless Network.

With both the hardware and software successfully installed into your computer,

you can quickly connect to a wireless network using the following methods.

Connect Using Windows Built-In Wireless Utility

Windows users may use the built-in wireless utility to connect to a wireless

network.

Windows XP users may use the built-in wireless utility. Follow the steps below:

3.1 In Windows XP

Right-click on the utility icon in your system tray (lower-right corner). Select

“Switch to Windows wireless configuration tool”.

Right-click on the wireless computer icon in your system tray (lower-right

corner). Select “View Available Wireless Networks”.

The utility will display any available wireless networks in your area. Click on a

network (displayed using the SSID) and click the “Connect” button.

Figure 3-1

Figure 3-2

Inhaltsverzeichnis

Andere Rosewill Adapter Handbücher

Rosewill

Rosewill RNX-AC600UB Bedienungsanleitung

Rosewill

Rosewill RNX-G1-G1W Bedienungsanleitung

Rosewill

Rosewill RPLC-500 Bedienungsanleitung

Rosewill

Rosewill RNX-G1LX Bedienungsanleitung

Rosewill

Rosewill RNX-G1 Bedienungsanleitung

Rosewill

Rosewill RNX-N180PCE Bedienungsanleitung

Rosewill

Rosewill RC-221 Bedienungsanleitung

Rosewill

Rosewill RNX-N150 Bedienungsanleitung

Rosewill

Rosewill RNX-N600UBE Bedienungsanleitung

Rosewill

Rosewill PW-AC5530U Bedienungsanleitung

Rosewill

Rosewill RNX-N250PCe Bedienungsanleitung

Rosewill

Rosewill Wireless Adapter RNX-EasyN1 Bedienungsanleitung

Rosewill

Rosewill RC207 Bedienungsanleitung

Rosewill

Rosewill WIRELESS N ADAPTER RNX-N150UBE Bedienungsanleitung

Rosewill

Rosewill RNX-N150PCX Bedienungsanleitung

Rosewill

Rosewill Ethernet Adapter Bedienungsanleitung

Rosewill

Rosewill RNF-405U Bedienungsanleitung

Rosewill

Rosewill RNX-AC600HGUBE Bedienungsanleitung

Rosewill

Rosewill RPLC-201 Bedienungsanleitung

Rosewill

Rosewill AC1200UBE Bedienungsanleitung

Rosewill

Rosewill RNX-B100 Bedienungsanleitung

Rosewill

Rosewill RNX-N180UBE Bedienungsanleitung

Rosewill

Rosewill RCAD-11001 Bedienungsanleitung

Rosewill

Rosewill RNX-N150HG Bedienungsanleitung

Beliebte Adapter Handbücher anderer Marken

PCB Piezotronics

PCB Piezotronics 090B274 Bedienungsanleitung

Auvidea

Auvidea J20 Produkthandbuch

Gossen MetraWatt

Gossen MetraWatt AT3-III E Bedienungsanleitung

Akribis

Akribis ITF-21-BISS-MIT Bedienungsanleitung

Tenda

Tenda W54U Bedienungsanleitung

ROHO

ROHO AGILITY Bedienungsanleitung

PROLiNK

PROLiNK WN2001 Bedienungsanleitung

Hawking

Hawking HUF2 Bedienungsanleitung

Airlink101

Airlink101 AWLC4030 Bedienungsanleitung

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Bedienungsanleitung

Philips

Philips SWA4554S/10 Bedienungsanleitung

JVC

JVC TS-C9D2B Gebrauchsanweisung

NETGEAR

NETGEAR A6100 Bedienungsanleitung

D-Link

D-Link DWA-121 Bedienungsanleitung

Philips

Philips SWA2037 Bedienungsanleitung

Basalte

Basalte 0610-20 Bedienungsanleitung

Yealink

Yealink EHS40 Bedienungsanleitung

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Bedienungsanleitung