Rowenta Steam 'n Press Bedienungsanleitung

Steam 'n Press

Instructions for Use

REF. 110 348 1059

IMPORTANT SAFETY

INSTRUCTIONS

When using your Rowenta Steam 'n Press basic precau-

tions should always be followed, including the following:

Read all instructions before using the appliance.

1. Use appliance only for its intended use.

2. To protect against a risk of electric shock, do not

immerse the appliance in water or other liquids.

Do not use the appliance in a wet environment (on a

wet floor, near a sink).

3. The appliance should always be turned to Minimum

(Min) before plugging or unplugging from outlet.

Never yank cord to disconnect from outlet, instead

grasp plug and pull to disconnect.

4. Do not allow cord to touch hot surfaces. Let

appliance cool completely before putting away.

Loop cord loosely around appliance when storing.

5. Always disconnect appliance from electrical outlet

when filling appliance with water, emptying

appliance or when not in use.

6. Do not operate appliance with a damaged cord or

if the appliance has been dropped or damaged. To

avoid the risk of electric shock, do not disassemble

the appliance, ship it to the nearest authorized

Rowenta Appliance Service Center for examination

and repair. Incorrect reassembly can cause a risk of

electric shock when the appliance is used.

7. This appliance is not a toy, so close supervision is

necessary for any appliance being used by or near

children. Do not leave appliance unattended while

plugged in or on an ironing board.

8. Burns can occur from touching hot metal parts, hot

water, steam or hot soleplate cover.

9. The use of accessory attachments not recommended

by Rowenta may result in fire, electric shock or

personal injury.

SPECIAL INSTRUCTIONS

1. This is a 1000 watt appliance. To avoid a circuit

overload, do not operate a high wattage appliance

on the same circuit.

2. If an extension cord is absolutely necessary, a

10-ampere cord should be used. Cords rated for

less amperage may overheat. Care should be taken

to arrange the cord so that it cannot be pulled or

tripped over.

3. Your Rowenta appliance is intended for household

use only.

4. IMPORTANT – Do not remove soleplate cover when

appliance is hot. Turn thermostat to minimum and

allow unit to cool. Always remove carefully and avoid

touching soleplate which will remain hot for some

time. Refer to full operating instructions.

SAVE THESE INSTRUCTIONS

■Description:

A Thermostat control dial

B Burst of steam button

C Removable water tank

D Cord protector

E Highy polished aluminum

soleplate

F Soleplate cover lock

G Lint pad

H Fabric brush

I Ribbed finger grip

J Soleplate cover

ABC D

J FGI E

USING FOR THE FIRST TIME

MPlease read the instructions for use and the Important Safety

Instructions carefully.

MIt is normal for a small amount of smoke to be produced the first

time the appliance is used. This will quickly disappear.

MWhen the appliance is plugged in and

thermostat control dial is moved from

the minimum setting, the soleplate

heats. Do not touch or remove the sole-

plate cover without letting the appliance

cool down.

MDuring use or while unit is heating or

cooling, do not rest appliance on its sole-

plate. Place product on its side on a firm,

heat resistant, flat surface, as soleplate

will be hot.

MAs the appliance heats the housing becomes warm.This is normal.

FILLING THE WATER TANK

Before plugging in the Steam 'n Press fill the water tank (C) with water

as follows:

Remove the water tank

MTo remove the water tank, hold on to

the bottom half of the handle and slide

the top half of the handle away from

the appliance as shown.

Filling the water tank

MRemove cap, fill the tank with ordinary

tap water and close the cap.

Replacing the water tank

MPut the full water tank back into the

unit, by sliding the lower handle back

into the top half of the handle until it is

firmly in place.

Adding water during use

MAlways unplug the appliance and wait for it to cool down before

removing the water tank.

MHandle with care as unit will remain hot for a considerable time.

MFill as indicated in water tank filling section.

MPlug in the appliance and wait approximately one minute to ensure

your Steam 'n Press is fully reheated before using it.

ATTACHING AND REMOVING THE SOLEPLATE COVER

Attaching the soleplate cover

The Steam 'n Press should be unplugged and completely cool when

removing or attaching the soleplate cover.

MTo attach the soleplate cover (J) to the

Steam 'n Press, hold the soleplate cover

by the ribbed finger grips (I) and slide

the cover over the soleplate.

MTurn the soleplate cover lock (F) half a

turn (180°) to the left to lock the sole-

plate cover into position.

MYour appliance can be used as a Steambrush once cover is attached.

Reference “Steambrush Function“ section of instructions for further

use information.

Removing the soleplate cover

The steambrush should be unplugged and completely cool when

removing or attaching the soleplate cover.

MTo remove the soleplate cover (J) turn

the soleplate cover lock (F) a half turn

(180°) to the right.

MGrip the soleplate cover by the ribbed

finger grips (I) on both sides as shown

and pull towards the tip of unit to

remove.

MReference “Ironing Function“ section of instructions for further use

information.

IRONING FUNCTION

The soleplate of the Steam 'n Press will smooth out tough wrinkles

from clothes and press in sharp creases and pleats.

Starting up

Before plugging in, please remove cover.

When the Steam 'n Press is plugged in the soleplate heats.

Do not touch or remove the soleplate cover without letting

the appliance cool down.

MRemove the soleplate cover as indicated in the instructions section

“Removing the Soleplate Cover“.

MPlug in the appliance, place it on its side

and wait approximately one minute for it

to reach full temperature before using.

MDuring use or while unit is heating or

cooling, do not rest it on its soleplate.

Place product on its side on a firm, flat,

heat-resistant surface, as it will be hot.

Never iron clothes while they are

being worn.

Selecting the temperature

MSet the thermostat control dial (A) according to the type of fabric

you are ironing. Check the fabric label for the appropriate setting.

Fabric Temperature

regulator

synthetics

nylon ●

polyester (low temperature)

silk ●●

wool (medium temperature)

cotton ●●●

linen (high temperature)

Start at low temperature ●and graduate to

high temperature ● ● ●. For delicate fabrics

we recommend carrying out a test on an

unobtrusive part of the garment (inner

seam). Steam can only be produced when

the thermostat is aligned to ● ● ● setting.

STEAMBRUSH FUNCTION

Using for the first time

When the Steam 'n Press is plugged

in the soleplate heats. Do not touch

or remove the soleplate cover

without letting the appliance cool

down.

MMake sure soleplate cover is securely

in place before using the steambrush

function. Please reference section in

instructions called “Attaching the

Soleplate Cover“.

MPlug in your Steam 'n Press and set the

thermostat to the ●●● steam setting.

MAfter approximately one minute it will

reach working temperature.

MTo begin steaming, press the burst of

steam button 4 to 5 times to prime the

unit.

NOTE: The Steam 'n Press can be used

on virtually all articles of clothing in the

home. Care should be taken when

steaming heat sensitive synthetic materi-

als such as nylon or rayon. We

recommend you test acrylic, nylon or

other synthetic fabrics on an unobtrusive

area to ensure these fabrics are not

damaged by hot steam.

To avoid damage to clothes from dust or dirt that may collect in

the appliance, we recommend that before the first use or after the

appliance has been stored for some time you test the burst of steam

on an old cloth.

Steaming clothes

MHang the wrinkled article of clothing on

a clothes hanger.

MPull the clothing tight with one hand

and place the appliance over the

creased area beginning at the top of

garment.

MGently press the fabric brush (H) against

the clothing and move the appliance

down over the fabric at the same time

pressing the burst of steam (B) every 4

seconds.

MThe combination of steam and the brush will gently remove the

wrinkles.

MAfter treatment, let the article of clothing cool down on the hanger

before wearing.

Never steam clothes while they are being worn.

Steaming drapes and upholstery

MWrinkles and creases can be removed from drapes while they are

hanging on the rods.

MSimply follow the procedure described in "Steaming clothes".

MAlways test first on unobtrusive area.

MWhen using the appliance horizontally return to the vertical position

occassionally to ensure maximum steam performance.

Lint pad

MThreads, lint and hair can easily be

moved with the lint pad (G) by

brushing the clothing slowly from left

to right.

The pad can be cleaned by brushing in

the opposite direction right to left on a

scrap of old cloth.

AFTER USING THE STEAMBRUSH

MSet the temperature control dial (A) to

min. then unplug the appliance. Empty

the water remaining in the tank and

leave unit on its side to cool.

Storage

MAfter the appliance has cooled down, it

may be stored in the bag provided.

CLEANING AND MAINTENANCE

If the body and the handle become dirty they should be wiped with a

damp cloth when the appliance is cold and unplugged. Do not use

abrasive or other chemicals.

Cleaning the soleplate

MIn normal use a draggy coating may build up on the soleplate

(starch, detergent buildup, burnt synthetic fibers). This can be easily

removed by using the Rowenta Soleplate Cleaning Kit or a quality

hot iron soleplate cleaner available at most stores.

MDo not use abrasive household cleaners or abrasive cleaning pads.

MTo prevent scratching of the soleplate, do not iron over sharp

objects (zippers, etc.). Do not place the appliance on rough

surfaces, e.g. metal iron support, which may scratch the soleplate.

WATER TO USE IN ROWENTA STEAM 'N PRESS

Tap water

The Rowenta Steam 'n Press is designed to be used with REGULAR TAP

WATER (up to 12 grains of hardness). If your water is harder than this,

Rowenta recommends mixing half tap water with half distilled water

which reduces the hardness; or just use inexpensive bottled spring

water.

Never use 100% distilled water since this can cause the iron to spit

and leak.

Softened water

There are many types of household water softeners and the water

from many of them is perfectly acceptable for use in the Steam 'n

Press. However, some types of softeners, particularly those that use

chemicals such as salt, can cause the appliance to leak or spit during

use. If you experience this type of problem, we recommend that you

try using inexpensive bottled spring water or untreated tap water.

Never use 100% pure distilled water.

Once you have changed water it will take several uses to correct the

problem. Rowenta recommends trying the steam function for the first

time on an old towel or cloth to avoid damaging your clothes.

Iron and other impurities

If your water supply contains large amounts of iron or organic

matter, these minerals can collect inside the appliance and eventually

appear as brown stains. If you experience these problems, Rowenta

recommends using inexpensive bottled spring water.

Never use 100% pure distilled water.

Always remember:

Battery water and water containing additives (such as starch, perfume

or fabric conditioner) may not be used. Such additives can affect the

properties of the steam and, at high temperatures, can form deposits

in the steam chamber, which will mark the laundry when they are

emitted through the steam vents. For this reason descaling liquids

should not be used.

In the interest of improving products, Rowenta reserves the right to

change specifications without prior notice.

Andere Handbücher für Steam 'n Press

Inhaltsverzeichnis

Andere Rowenta Dampfreiniger Handbücher

Rowenta

Rowenta X-cel Steam Easy DR71 Series Bedienungsanleitung

Rowenta

Rowenta GS6010 Bedienungsanleitung

Rowenta

Rowenta REF. 3460984 Bedienungsanleitung

Rowenta

Rowenta RY6535WI Bedienungsanleitung

Rowenta

Rowenta IS5100 Bedienungsanleitung

Rowenta

Rowenta X-CEL STEAM FIRST DR61 Series Bedienungsanleitung

Rowenta

Rowenta TWEENY NI50 Series Bedienungsanleitung

Rowenta

Rowenta IS95 Series Bedienungsanleitung

Rowenta

Rowenta DG8624U1 Bedienungsanleitung

Rowenta

Rowenta GS6020U1 Bedienungsanleitung

Rowenta

Rowenta Pure Pop DR2022 Bedienungsanleitung

Rowenta

Rowenta IS34 Bedienungsanleitung

Rowenta

Rowenta STEAM POWER Bedienungsanleitung

Rowenta

Rowenta Tweeny Nano DV90 Series Bedienungsanleitung

Rowenta

Rowenta PRO STYLE CARE IS84 Series Bedienungsanleitung

Rowenta

Rowenta YR3040D1 Bedienungsanleitung

Rowenta

Rowenta GS6030 Bedienungsanleitung

Rowenta

Rowenta X-CEL STEAM DR80 series Bedienungsanleitung

Rowenta

Rowenta ACCESS STEAM MINUTE DT70 Series Bedienungsanleitung

Rowenta

Rowenta X'CEL STEAM+ DR81 Series Bedienungsanleitung

Rowenta

Rowenta Pure Pop DR20 Series Bedienungsanleitung

Rowenta

Rowenta PRO STYLE IS3440 Bedienungsanleitung

Rowenta

Rowenta Clean&Steam Multi Bedienungsanleitung

Rowenta

Rowenta IS34 Bedienungsanleitung

Beliebte Dampfreiniger Handbücher anderer Marken

Oreck

Oreck STEAM-IT STEAM100LRH Bedienungsanleitung

Beautural

Beautural YPZ-146 Bedienungsanleitung

MPM

MPM MZP-02 Bedienungsanleitung

Electrolux

Electrolux Refine 500 Bedienungsanleitung

Kärcher

Kärcher SC 3 Premium Bedienungsanleitung

Shark

Shark PRO Steam & Spray Bedienungs- und Wartungsanleitung

Jula

Jula 802-337 Bedienungsanleitung

Haan

Haan Floor Sanitizer MS-30 Bedienungsanleitung

Black & Decker

Black & Decker HSM13E1 Bedienungsanleitung

HOFFEN

HOFFEN GS-1231 Bedienungsanleitung

POLTI

POLTI VAPORETTO SYSTEME PRO Bedienungsanleitung

eta

eta AQUASIM PRO Bedienungsanleitung

Maxwell

Maxwell MW-3715 G Bedienungsanleitung

VAPamore

VAPamore Primo MR-100 Handbuch

Bestron

Bestron AZQ016 Bedienungsanleitung

Nilfisk-ALTO

Nilfisk-ALTO Steamtec 312 Bedienungsanleitung

Tempo di saldi

Tempo di saldi SPINSCRUBBER Bedienungsanleitung

DOMENA

DOMENA HYGIAFLOR Bedienungsanleitung