RPS TPP-750 Bedienungsanleitung
RPS Tankless
Pressure Pump™
TPP-750 User Manual
With the RPS Tankless
Pressure Pump™
system you'll get
smooth continuous
steady reliable water
pressure without the
need for AC power or
the utility grid.
The solar charged
battery bank powers a
centrifugal booster
pump that varies its
speed and power based
on your demand for
water at the exact
pressure you select
from 20 to 45psi.
1. Loosen Priming Screw.
2. Create positive pressure in supply line to
push water into pump inlet or fill line with water
3. Once air is completely purged, power on
the pump to purge air completely before fully
tightening Priming Screw again
4. Adjust Pressure Setting with controls. Pump
will adjust speed and smoothly cycle on & off to
maintain desired setting.
NEW: Wire Priming ‘hook’ in the kit allows
you to reach into the top outlet of the
pump and pull up the small ring on the
check valve so you can pour water in the
top and fill the chamber easily.
PRIMING VIDEO: ** Very Helpful
http://www.youtube.com/c/RPSSolarPumps
PRIMING YOUR PUMP
TPP PLUMBING OPTIONS
* Important: Care should be taken when plumbing to ensure tight connections and maintain prime.
Use teflon tape or thread sealant on all connections. Minor leaks or seepage will cause the pump to
cycle and deplete the batteries.
Your Tankless Pressure Pump can
plumb directly from your storage tank to
your main line. It will auto-adjust speed
to maintain pressure.
You can also draw water up from a
pond, shallow well or cistern (up to
15ft) but you must maintain prime with
a footvalve and tight connections.
Inlet 1.25" FNPT Power Range 750 - 1500w
Outlet 1" FNPT Suction Up to 4M, 15ft (wetted)
Acceptable pH 5 - 8, Water (No Fuel) Max Current 8 Amps
Temp. Range 0 - 40°C, 32 - 104°F Box Size 394 x 260 x 330mm
Max Liquid Temp 90°C, 194°F Weight 10kg, 22lbs
TPP PUMP DIMENSIONS
Compatible Pump TP-750 Only
Battery Voltage 24 VDC Only
Battery Wiring 10AWG or Thicker
Dimensions 300mm x 270mm x 95mm,
12in x 11in x 4in
Temp. Range 0 - 40°C, 32 - 104°F
OPTIONAL AC INPUT
(See 220v Wiring)
220 VAC Only
Weight 2.17kg, 4.8lbs
Recommended
Clearance
Mount with 12 inches of space
in all directions
TPP CONTROLLER DIMENSIONS
INSTALLATION DETAILS
Ensure there are no shadows or other obstructions on the solar panels. While shadowing a small
corner of a single panel may not seem like a big deal, since the panels are connected in series, a
small shadow can limit the power output from all other panels connected in series! This means a
small shadow on a single panel could reduce system power by hundreds of watts. Time to get out
that chainsaw and trim some trees!
TPP CONTROLLER — Your Controller is not waterproof and should be located in a dry dust-free
location, protected from the sun and the elements and pests such as mice and bugs. Mice love to
chew wires and spiders and moths will build nests wherever they can find room. While we
understand you cannot eliminate all pests, it might be time to spray some insecticides around your
shed and set some mousetraps! There is nothing worse than finding insulation chewed off your
electrical wires. *The fan remains running in low power mode at all times to protect the equipment.
This fan uses very little power and it running, increases the lifetime of the system.
TPP PUMP - Your pump is designed for use out of the direct elements, sun, rain and snow.
Covering or building into a small enclosure is ideal. Since water does expand when it freezes, care
should be taken to winterize the system if being used in a climate that experiences hard freezing. If
foot valve is being used, care should be taken in plumbing the intake to ensure tight connections
which will avoid the loss of prime.
Batteries - Unless you already bought a TPP system that included the appropriate number of RPS
55Ah 12V Deep Cycle GEL batteries, customers will need to supply their own battery bank. RPS
recommends 12V AGM / sealed lead acid batteries that are designed for maintenance free
operation. More common flooded deep cycle marine or RV batteries can also be used. Batteries
should be stored in a dry location protected from the elements.
RPS SOLAR PANELS — Solar panels should
be mounted on a secure structure, ground
mount or top of pole mount. Several ideas can
be found at www.RPSSolarPumps.com.
Panels should face true South and at an angle
appropriate for your latitude. If you are
mounting your panels on an already built
structure, try to get as close to the correct
angle as possible.
TP-750- 2
TP-750- 4
TP-750- 8
WIRING YOUR SOLAR PANELS
You will link your solar
panels together and connect
to the controller by clipping
MC4 connectors together.
Each MC4 connector is
either a male end or female
end (see
image).
They simply
snap together
to make safe
and easy
connections.
Note: If using your own
solar panels do not
exceed 55Voc input!
BATTERY WIRING 24V ONLY
2x 12v Battery Configuration
Batteries Wired in Series
Recommended 8 AWG wire
4x 12v Battery Configuration
Batteries Wired in Series / Parallel
Recommended 8 AWG wire
4x 6v Battery Configuration
Batteries Wired in Series
Recommended 8 AWG wire
RPS recommends AGM / sealed lead acid batteries that are designed for several maintenance
free years of operation. They should also be stored in a dry location protected from the elements.
To prevent significant voltage drop, the batteries should be located as close to the Controller as
possible. Within 3 feet is ideal. If further than 3ft is required, the wires may be extended using
appropriate gauge cables. The batteries operate best at room temperature and it is best to keep
them out of freezing conditions for maximum performance.
Note: Do not exceed two 12V batteries in
series or four 6V batteries in series. For
extra battery capacity add sets in parallel.
CONTROLLER DISPLAY
220V AC INPUT (Only if Required)
Your Controller is designed to take solar power and charge your 24v battery
bank. As an optional backup, it is also setup to accept 220V AC to both charge
your batteries and run your pump directly if desired. There is a 3 prong outlet
and a pigtail in your kit that allows for the wiring of 220v line power connector.
Wiring 220v is only for certified professionals or those familiar with 220v power.
Green Stripe Wire - GROUND
Blue (or Black) Wire - L1 HOT
Yellow (or Red) Wire - L2 HOT
Wire out or cap your neutral wire. L1 L2
G
Dieses Handbuch passt für folgende Modelle
3
Inhaltsverzeichnis
Andere RPS Wasserpumpe Handbücher
Beliebte Wasserpumpe Handbücher anderer Marken
Sykes AmeriPumps
Sykes AmeriPumps GP100M Fehlerbehebungshandbuch
DUROMAX
DUROMAX XP WX Series Bedienungsanleitung
BRINKMANN PUMPS
BRINKMANN PUMPS SBF550 Bedienungsanleitung
Franklin Electric
Franklin Electric IPS Bedienungsanleitung
Xylem
Xylem e-1532 Series Bedienungsanleitung
Milton Roy
Milton Roy PRIMEROYAL Bedienungsanleitung