RS PRO IDM-8351 Bedienungsanleitung

Instruction Manual

IDM-8351

Dual Measurement Multimeter

EN FR DE IT SP

Table of Contents

17/11/2016 Version No. 002 1

Table of Contents

SAFETY INSTRUCTIONS............................................................................3

GETTING STARTED....................................................................................9

Characteristics ............................................................10

Appearance.................................................................12

Set Up ........................................................................22

OPERATION ..............................................................................................27

Basic Measurement Overview ......................................29

AC/DC Voltage Measurement.......................................31

AC/DC Current Measurement.......................................37

Resistance Measurement.............................................41

Diode Test...................................................................44

Capacitance Measurement...........................................45

Continuity Test ............................................................47

Frequency/Period Measurement...................................50

Temperature Measurement...........................................53

Dual Measurement Overview........................................57

Advanced Measurement Overview................................62

dBm/dB/W Measurement .............................................63

Max/Min Measurement.................................................66

Relative Measurement .................................................67

Hold Measurement ......................................................69

Compare Measurement................................................70

Math Measurement......................................................72

SYSTEM/DISPLAY CONFIGURATION.......................................................76

View Serial Number .....................................................77

View Version Number ..................................................78

Brightness Settings .....................................................79

IDM-8351 Instruction Manual/English

2 17/11/2016 Version No. 002

Continuity Beeper Settings ...........................................80

Input Resistance Settings.............................................81

Frequency/Period Input Jack Settings ...........................82

Digital Filter.................................................................83

Restore Factory Default Settings ..................................87

Trigger ........................................................................88

DIGITAL I/O................................................................................................90

Digital I/O Overview.....................................................91

REMOTE CONTROL ................................................................................. 95

Configure Remote Control Interface..............................96

Return to Local Control ..............................................100

COMMAND OVERVIEW .......................................................................... 101

Command Syntax.......................................................101

Command List ...........................................................106

FAQ.........................................................................................................152

APPENDIX...............................................................................................154

System Menu Tree.....................................................154

Factory Default Settings.............................................155

Replacing the AC Source Fuse ...................................156

Replacing the Input Fuse ...........................................157

Status system............................................................159

Specifications ............................................................161

Additional Specifications ............................................167

Dimensions ...............................................................173

Declaration of Conformity...........................................174

INDEX......................................................................................................175

SAFETY INSTRUCTIONS

17/11/2016 Version No. 002 3

SAFETY INSTRUCTIONS

This chapter contains important safety instructions that you must

follow during operation and storage. Read the following before

any operation to ensure your safety and to keep the instrument in

the best possible condition.

Safety Symbols

These safety symbols may appear in this manual or on the instrument.

WARNING

Warning: Identifies conditions or practices that could result in

injury or loss of life.

CAUTION

Caution: Identifies conditions or practices that could result in

damage to the DMM or to other properties.

DANGER High Voltage

Attention Refer to the Manual

Protective Conductor Terminal

Earth (ground) Terminal

IDM-8351 Instruction Manual/English

4 17/11/2016 Version No. 002

Do not dispose electronic equipment as unsorted municipal

waste. Please use a separate collection facility or contact the

supplier from which this instrument was purchased.

Safety Guidelines

General

Guideline

CAUTION

Make sure that the voltage input level does not exceed

DC1000V/AC750V.

Make sure the current input level does not exceed 12A.

Do not place any heavy object on the instrument.

Avoid severe impact or rough handling that can lead to

damaging the instrument.

Do not discharge static electricity to the instrument.

Use only mating connectors, not bare wires, for the terminals.

Do not block or obstruct the cooling fan vent opening.

Do not perform measurement at the source of a low-voltage

installation or at building installations (Note below).

Do not disassemble the instrument unless you are qualified as

service personnel.

Make sure that the COM terminal to earth is limited to 500Vpk.

Remove all test leads before disconnecting the mains power

cord from the socket.

SAFETY INSTRUCTIONS

17/11/2016 Version No. 002 5

(Note) EN 61010-1:2010 specifies the measurement categories and their

requirements as follows. The IDM-8351 falls under category II 600V.

Measurement category IV is for measurement performed at the source of low-

voltage installation.

Measurement category III is for measurement performed in the building

installation.

Measurement category II is for measurement performed on the circuits directly

connected to the low voltage installation.

Power Supply

WARNING

AC Input voltage: 100/120/220/240 V AC

50/60Hz

The power supply voltage should not fluctuate more than 10%.

Connect the protective grounding conductor of the AC power

cord to an earth ground, to avoid electrical shock.

Fuse

WARNING

Fuse type: 0.125AT 100/120VAC

0.063AT 220/240 VAC

Make sure the correct type of fuse is installed before power up.

To avoid risk of fire, replace the fuse only with the specified

type and rating.

Disconnect the power cord before fuse replacement.

Make sure the cause of a fuse blowout is fixed before fuse

replacement.

IDM-8351 Instruction Manual/English

6 17/11/2016 Version No. 002

Cleaning the

Instrument

Disconnect the power cord before cleaning.

Use a soft cloth dampened in a solution of mild detergent and

water. Do not spray any liquid.

Do not use chemicals containing harsh material such as

benzene, toluene, xylene, and acetone.

Operation

Environment

Location: Indoor, no direct sunlight, dust free, almost non-

conductive pollution (Note below)

Temperature: 0°C to 50°C

Humidity: < 30°C: < 80%RH(non-condensing);

30°C~40°C:<70%RH(non-condensing); >40°C:

<50%RH (non-condensing)

Altitude: <2000m

(Note) EN 61010-1:2010 specifies the pollution degrees and their requirements as

follows. The IDM-8351 falls under degree 2.

Pollution refers to “addition of foreign matter, solid, liquid, or gaseous (ionized

gases), that may produce a reduction of dielectric strength or surface

resistivity”.

Pollution degree 1: No pollution or only dry, non-conductive pollution occurs.

The pollution has no influence.

Pollution degree 2: Normally only non-conductive pollution occurs.

Occasionally, however, a temporary conductivity caused by condensation must

be expected.

Pollution degree 3: Conductive pollution occurs, or dry, non-conductive

pollution occurs which becomes conductive due to condensation which is

SAFETY INSTRUCTIONS

17/11/2016 Version No. 002 7

expected. In such conditions, equipment is normally protected against

exposure to direct sunlight, precipitation, and full wind pressure, but neither

temperature nor humidity is controlled.

Storage

environment

Location: Indoor

Temperature: -40°C to 70°C

Humidity: <90%RH(non-condensing)

Disposal

Do not dispose this instrument as unsorted municipal waste.

Please use a separate collection facility or contact the supplier

from which this instrument was purchased. Please make sure

discarded electrical waste is properly recycled to reduce

environmental impact.

IDM-8351 Instruction Manual/English

8 17/11/2016 Version No. 002

Power cord for the United Kingdom

When using the unit in the United Kingdom, make sure the power cord meets the

following safety instructions.

NOTE: This lead/appliance must only be wired by competent persons

WARNING: THIS APPLIANCE MUST BE EARTHED

IMPORTANT: The wires in this lead are coloured in accordance with the following code:

Green/ Yellow:

Earth

Blue:

Neutral

Brown:

Live (Phase)

As the colours of the wires in main leads may not correspond with the coloured

marking identified in your plug/appliance, proceed as follows:

The wire which is coloured Green & Yellow must be connected to the Earth terminal

marked with either the letter E, the earth symbol or coloured Green/Green &

Yellow.

The wire which is coloured Blue must be connected to the terminal which is marked

with the letter N or coloured Blue or Black.

The wire which is coloured Brown must be connected to the terminal marked with

the letter L or P or coloured Brown or Red.

If in doubt, consult the instructions provided with the equipment or contact the

supplier.

This cable/appliance should be protected by a suitably rated and approved HBC

mains fuse: refer to the rating information on the equipment and/or user instructions

for details. As a guide, a cable of 0.75mm2should be protected by a 3A or 5A fuse.

Larger conductors would normally require 13A types, depending on the connection

method used.

Any exposed wiring from a cable, plug or connection that is engaged in a live

socket is extremely hazardous. If a cable or plug is deemed hazardous, turn off the

mains power and remove the cable, any fuses and fuse assemblies. All hazardous

wiring must be immediately destroyed and replaced in accordance to the above

standard.

Inhaltsverzeichnis

Andere RS PRO Multimeter Handbücher

RS PRO

RS PRO RS IDM-20 Bedienungsanleitung

RS PRO

RS PRO IDM 98IV Bedienungsanleitung

RS PRO

RS PRO LCR 1701 Bedienungsanleitung

RS PRO

RS PRO ICM 135R Bedienungsanleitung

RS PRO

RS PRO RS-965T Bedienungsanleitung

RS PRO

RS PRO RS-9663 Bedienungsanleitung

RS PRO

RS PRO RS-9660B Bedienungsanleitung

RS PRO

RS PRO IDM93N Bedienungsanleitung

RS PRO

RS PRO RS-660 Bedienungsanleitung

RS PRO

RS PRO RS-218 Bedienungsanleitung

RS PRO

RS PRO RS-9889 Bedienungsanleitung

RS PRO

RS PRO RS-946 Bedienungsanleitung

RS PRO

RS PRO ICM 139R Bedienungsanleitung

RS PRO

RS PRO RS-9519BT Bedienungsanleitung

RS PRO

RS PRO IDM201N Bedienungsanleitung

RS PRO

RS PRO RS-927A Bedienungsanleitung

RS PRO

RS PRO RS-338 Bedienungsanleitung

RS PRO

RS PRO IDM 71 Bedienungsanleitung

RS PRO

RS PRO S1 Bedienungsanleitung

RS PRO

RS PRO IDM-8341 Series Bedienungsanleitung

RS PRO

RS PRO IPM 138N Bedienungsanleitung

RS PRO

RS PRO RS-989 Bedienungsanleitung

RS PRO

RS PRO RS-9963T Bedienungsanleitung

RS PRO

RS PRO RS-9519BT Bedienungsanleitung

Beliebte Multimeter Handbücher anderer Marken

Agilent Technologies

Agilent Technologies 34420A Bedienungsanleitung

Fluke

Fluke 83 Bedienungsanleitung

Hameg

Hameg HM 8012 Bedienungsanleitung

Mastech

Mastech MY70 Bedienungsanleitung

Steren

Steren MUL-300 Bedienungsanleitung

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Bedienungsanleitung

PeakTech

PeakTech 4000 Gebrauchs- und Pflegehandbuch

YOKOGAWA

YOKOGAWA 90050B Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Bedienungsanleitung

Fluke

Fluke 8846A Bedienungs- und Wartungshandbuch

Tempo Communications

Tempo Communications MM200 Bedienungsanleitung

Elenco Electronics

Elenco Electronics CM-1555 Bedienungsanleitung

Mastech

Mastech MS8238C Bedienungsanleitung

SDAR

SDAR 830A, 830B, 830D, 830C Bedienungsanleitung

BGS technic

BGS technic 8890 Bedienungsanleitung

Amprobe

Amprobe Hexagon 60 Bedienungsanleitung

Morris

Morris 57074 Bedienungsanleitung