RS PRO IDM93N Bedienungsanleitung



INSTRUCTION MANUAL

IDM93N DIGITAL MULTIMETER

EN IT DEFR

IDM 93N

DIGITAL MULTIMETER

INSTRUCTION MANUAL

WARNING

THE SERVICING INSTRUCTIONS DESCRIBED WITHIN THIS MANUAL ARE FOR USE BY QUALIFIED

PERSONNEL ONLY. TO AVOID ELECTRIC SHOCK, DO NOT PERFORM ANY SERVICING OTHER

THAN THAT CONTAINED IN THE OPERATING INSTRUCTIONS UNLESS YOU ARE QUALIFIED TO

DO SO. TO AVOID ELECTRIC SHOCK, DISCONNECT MEASURING TERMINALS BEFORE OPENING

ENCLOSURE.

INTRODUCTION

1-1 Unpacking and Inspection

Upon removing your new Digital Multimeter from its packing, you should have the following items:

1. Digital Multimeter.

2. Test lead set (one black, one red).

3. Instruction Manual.

4. Protective holster.

1-2 Meter Safety

Terms marked on Equipment

ATTENTION —Refer to Manual.

DOUBLE INSULATION —Protection Class II.

DANGER —Risk of electric shock

Symbols in this Manual

This symbol indicates where cautionary or other information is found in the manual.

Fuse.

<Battery.

1-3 Front Panel

Refer to Figure 1 and the following numbered steps to familiarize yourself with the meter's front panel controls and

connectors.

1. Digital Display —The digital display has a 3-1/2 digit LCD readout (maximum reading 1999) with automatic

polarity, decimal point, overrange and low battery indicators.

2. Rotary Switch —Selects the desired function and range.

3. COM Input Terminal —Ground input connector.

4. VΩHz Input Terminal —Positive input connector for Volts, Ohms, Diode (Continuity) and Frequency measurements.

5. µA mA Input Terminal —Positive input connector for current measurements (up to 200mA).

6. 10A Input Terminal —Positive input connector for current measurements (up to 10A).

7. Capacitor Test Input terminals —Used for capacitance measurements.

8. AC/DC Switch —Select AC or DC for voltage and current measurements.

Figure 1

SPECIFICATIONS

2-1 General Specifications

This instrument has been designed in accordance with UL 3111 and IEC publication 1010 Pt 1, Class II, Safety

Requirements for Electrical Equipment for Measurement, Control and Laboratory use. This level of safety can

only be guaranteed while the limits of section 2.2 are observed.

Display : 3-1/2 digit Liquid Crystal Display (LCD) with a maximum reading of 1999.

Polarity Indication : Automatic, positive implied, negative indicated.

Overrange Indication : "1" or "-1".

Low Battery Indication : "<" is displayed when the battery voltage drops below specified operating voltage.

Measuring Rate : 2.5 times per second, nominal.

Auto Power Off : Approx. 30 minutes.

Temperature Coefficient : 0.15 x (Specified accuracy) / °C, < 18°C or > 28°C.

Power Requirements : Alkaline 9V battery.

Battery Life : 150 hours typical (Alkaline).

Dimensions (WxHxD) : 84mm x 175mm x 31mm, without holster

95mm x 192mm x 50mm, with holster.

Weight (including battery) : 340 gms without holster

550 gms with holster.

Accessories : Protective Holster, battery (installed) and instruction manual.

2-2 Environmental Conditions

Indoor Use

Maximum Altitude : 2000 meters.

Installation Category : IEC 1010 600V CAT. II, 300V CAT. III

Pollution Degree : 2

Operating Ambient : 0°C ~ 30°C ≦80% R.H., 30°C ~ 40°C ≦75% R.H., 40°C ~ 50°C ≦45% R.H.

Storage Temperature : -20°C to 60°C, with battery removed from meter.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere RS PRO Multimeter Handbücher

RS PRO

RS PRO RS-9660B Bedienungsanleitung

RS PRO

RS PRO RS-9889 Bedienungsanleitung

RS PRO

RS PRO RS-9663 Bedienungsanleitung

RS PRO

RS PRO RS-965T Bedienungsanleitung

RS PRO

RS PRO LCR 1701 Bedienungsanleitung

RS PRO

RS PRO IPM 138N Bedienungsanleitung

RS PRO

RS PRO IDM201N Bedienungsanleitung

RS PRO

RS PRO S1 Bedienungsanleitung

RS PRO

RS PRO ICM 135R Bedienungsanleitung

RS PRO

RS PRO IDM-8341 Series Bedienungsanleitung

RS PRO

RS PRO RS-218 Bedienungsanleitung

RS PRO

RS PRO IDM-8351 Bedienungsanleitung

RS PRO

RS PRO RS-927A Bedienungsanleitung

RS PRO

RS PRO RS IDM-20 Bedienungsanleitung

RS PRO

RS PRO RS-338 Bedienungsanleitung

RS PRO

RS PRO RS-946 Bedienungsanleitung

RS PRO

RS PRO IDM 98IV Bedienungsanleitung

RS PRO

RS PRO RS-9519BT Bedienungsanleitung

RS PRO

RS PRO ICM33II Bedienungsanleitung

RS PRO

RS PRO RS-660 Bedienungsanleitung

RS PRO

RS PRO RS-9519BT Bedienungsanleitung

RS PRO

RS PRO RS-989 Bedienungsanleitung

RS PRO

RS PRO ICM 139R Bedienungsanleitung

RS PRO

RS PRO RS-9963T Bedienungsanleitung

Beliebte Multimeter Handbücher anderer Marken

Agilent Technologies

Agilent Technologies 34420A Bedienungsanleitung

Fluke

Fluke 83 Bedienungsanleitung

Hameg

Hameg HM 8012 Bedienungsanleitung

Mastech

Mastech MY70 Bedienungsanleitung

Steren

Steren MUL-300 Bedienungsanleitung

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Bedienungsanleitung

PeakTech

PeakTech 4000 Gebrauchs- und Pflegehandbuch

YOKOGAWA

YOKOGAWA 90050B Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Bedienungsanleitung

Fluke

Fluke 8846A Bedienungs- und Wartungshandbuch

Tempo Communications

Tempo Communications MM200 Bedienungsanleitung

Elenco Electronics

Elenco Electronics CM-1555 Bedienungsanleitung

Mastech

Mastech MS8238C Bedienungsanleitung

SDAR

SDAR 830A, 830B, 830D, 830C Bedienungsanleitung

BGS technic

BGS technic 8890 Bedienungsanleitung

Amprobe

Amprobe Hexagon 60 Bedienungsanleitung

Morris

Morris 57074 Bedienungsanleitung