RS Peltor HTRXS Handbuch
RS stock no. 765-886
Issued March 1997 10612
FM Radio hearing
protector
Instruction Leaflet
The Peltor Workstyle Hearing Protector Radio has been tested and approved in accordance with
PPE directive 89/686/EEC and the EMC directive 89/336/EEC, which means that the requirements
for CE marking have been duly met. In order to get the best performance from your new purchase,
it is important that you read through the entire instructions.
Peltor workstyle hearing protector radio HTRXS (RS stock no.765-886) is a high-attenuation hearing
protector with a built-in high-sensitivity FM stereo radio receiver. The interference-suppressed
sound reproduction in stereo comes into its own noisy environments.Hearing protector radio HTRXS
is specially developed to improve safety and motivation for wearers in noisy conditions. It can also
be used for activities such as mowing the lawn or other work when the wearer wants to listen to the
radio without outside interruption.
1. Extra wide headband with soft padding for maximum comfort throughout the working day.
2. Low two-point attachment and simple height adjustment without protruding parts.
3. Individually sprung bands of stainless spring steel ensure uniform pressure around the ears.
Retain their tension better than plastic bands within a wide temperature range.
4. Soft and wide foam/fluid sealing cups with built-in pressure-equalisation ducts for low contact
pressure, effective sealing and maximum comfort.
5. Protected controls for ON/OFF, volume and channel selection.
6. Extra-short flexible antenna with low attachment and high reception sensitivity.
7. Simple, stable channel adjustment. Frequency range 88-108 Mhz.
8. Automatic gentle switchover from stereo to mono,for interference-free reception in areas with a
weak signal.
9. Volume limitation max. 82 dBA equivalent noise level.
10. Battery cover for simple battery replacement (two alkaline AA 1.5 volt batteries not included).
140 hours operation with fresh batteries.
Important user information
The hearing protector radio must be switched on, adjusted, cleaned and maintained in accordance
with these instructions.
●Wear your hearing protector radio all the time when you are in a noisy environment so as to
obtain maximum protective effect.
●Clean the outside of the hearing protector radio regularly with soap and lukewarm water. Do
not immerse in water.
●Do not store the hearing protector radio at temperatures above +55ºC, for example behind a
windscreen or a window.
●This product can be impaired by certain chemical substance. further information can be
obtained from the manufacturer.
●Replace the batteries when interference in the receiver increases or when the volume gets
weak.
●Inserting the battery with incorrect polarity may damage the receivers electronics. Never
replace the battery while the unit is switched on. before use, check that the battery is correctly
inserted.
●The hearing protector radio and in particular the sealing cups may be impaired in time and
should be checked frequently to ensure that there are no cracks or noise penetration.
Note: If these recommendations are not followed, both attenuation and function may be impaired.
User instructions
Unscrew and remove battery lid.Insert the two 1.5 volt batteries which are provided.Check that the
+ and - terminals face the right direction.
Headband:
Pull out the cups and adjust the headset over the ears so that the sealing pads completely surround
the ears. Adjust the height of both cups while holding down the band until you have a comfortable
fit. The band should fit straight on top of your head.
Helmet attachment:
Fit the helmet attachment in the hard-hat slot until it clicks into place.
During use, the wire bands must be pushed in until they click on both sides, from ventilation to
operating position. Check that the cup and wire band do not chafe against the harness or hard-hats
edge when in the operating position, otherwise this may cause noise penetration.
Note:The cups can be set to three positions, operational, ventilation and standby.
Important: For best protective effect, move away hair from around the ears so that the sealing cups
fit tightly on the head. Spectacle arms should be as thin as possible and fit close to the
head.
Turn on the volume control and adjust the required channel with the channel knob on the right cup.
The right cup also has a manual stereo-mono switch which can be set to mono for best reception
when the transmission signal is weak, for example when entering deep into a building. With this
switch in stereo, the receiver automatically switches between stereo and mono depending on the
strength of the transmission signal.
Attenuation
The attenuation rates for the Peltor Workstyle Hearing Protector Radio are tested and approved
according to PPE directive 89/686 EEC,and as per relevant sections of European standard EN 352-
1: 1993/pr EN 352-3.
Telephone receiver level for music is rated at max 80 dB(A) equivalent noise level as per the
requirements in the PPE directive.
Model HTRXS7A with headband.Weight 340g
Certificate issued by FIOH, Laajaniityntie 1, FIN-0162o,Vantaa. ID#0403.
The Peltor Workstyle Hearing Protector Radio meets the requirements in the EMC directive. EL
protector auricular Workstyle con radio FM estéreo, cumple con los requisitos de la Directiva EMC
.
Model Freq. Hz 125 250 500 1000 2000 4000 8000
H M L SNR
Mean att. 18.9 24.1 30.7 36.8 32.1 38.4 40.0
HTRXS Std.dev. 4.6 2.6 2.6 3.4 3.4 3.0 2.3
32dB 29dB 22dB 31
APV 14.3 21.5 28.1 33.4 28.7 35.4 37.7
The information provided in RS technical literature is believed to be accurate and reliable; however, RS
Components assumes no responsibility for inaccuracies or omissions, or for the use of this information,and all use
of such information shall be entirely at the user’s own risk.
No responsibility is assumed by RS Components for any infringements of patents or other rights of third parties
which may result from its use.
Specifications shown in RS Components technical literature are subject to change without notice.
RS Components, PO Box 99, Corby, Northants, NN17 9RS Telephone: 01536 201234
An Electrocomponents Company © RS Components 1997
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere RS Schutzvorrichtung Handbücher
Beliebte Schutzvorrichtung Handbücher anderer Marken
nxt
nxt BIA-nXt-DPC 1-22 Bedienungsanleitung
TFortis
TFortis SG-Switch Bedienungsanleitung
BERNINI DESIGN
BERNINI DESIGN Be172 Bedienungsanleitung
Rayleigh Instruments
Rayleigh Instruments RI-ENERGYSET-3P-ESS-50-100 Bedienungsanleitung
GE
GE Multilin 3 Series Bedienungsanleitung
E.K.T.
E.K.T. ke-DP01 Bedienungsanleitung
