RTI Miravue VIP-1 Bedienungsanleitung

1 | Page

01/2019

RTI | Miravue VIP-1 Manual

Contents

1) Miravue VIP-1 Driver Configuration................................................................................................................................ 2

2) Setting up Miravue VIP-1 as Expansion Device ............................................................................................................... 5

3) Miravue VIP-1 Programming Options ............................................................................................................................. 7

4) The RTI | Miravue VIP-1 Web Interface .......................................................................................................................... 9

a. Accessing the Setup Web Interface ............................................................................................................................ 9

b. HDMI Configuration .................................................................................................................................................. 10

c. Network Configuration ............................................................................................................................................. 11

d. Network Video Streams ............................................................................................................................................ 12

e. Other Settings ........................................................................................................................................................... 12

f. Firmware ................................................................................................................................................................... 13

g. Actions....................................................................................................................................................................... 13

5) VIP-1 Front Panel Ports ................................................................................................................................................. 14

6) VIP-1 Rear Panel Ports................................................................................................................................................... 15

7) VIP-1 Accessories........................................................................................................................................................... 16

8) Distributed vs. Centralized Design ................................................................................................................................ 17

9) Unicast vs. Multicast ..................................................................................................................................................... 19

10) Frequently Asked Question........................................................................................................................................... 21

2 | Page

01/2019

RTI | Miravue VIP-1 Manual

1) Miravue VIP-1 Driver Configuration

Download the current version of the Miravue driver and documentation on the RTI dealer site. Unzip the contents of the

driver to the directory where APEX points to for drivers. This can be changed by clicking the “Options” tab in the top

toolbar and selecting “set directories.”

Using the “Add Workspace Item” select the driver tab and search for “Miravue” using the search box.

3 | Page

01/2019

RTI | Miravue VIP-1 Manual

Select a room or global area where the Miravue should be located and click “Next” to add the driver to APEX.

Since this is a new instance of the driver, it will automatically generate a “Transceiver 1” naming convention.

It is recommended that you change the name to something that will help you identify the device when

programming. Name it “Living Room Miravue” or “Blu-Ray Miravue” depending on the display, source, or

location it is serving. Continue this process adding all the Miravue devices to the project file.

Repeat the process to add additional devices, making sure the ”Instance” drop-down field is set to the existing

driver. This will continue to increment the Miravue count as you add more Miravue VIP-1’s.

4 | Page

01/2019

RTI | Miravue VIP-1 Manual

Once all VIP-1 devices are added, you must configure the driver properties before continuing. Select the

Miravue driver from the driver section of the system tree and select “driver properties.” Enter the transceiver

count to match the number of Miravue units in your project file. This will open configuration options for all

your devices. Refer to the driver configuration documentation for additional instructions.

5 | Page

01/2019

RTI | Miravue VIP-1 Manual

2) Setting up Miravue VIP-1 as Expansion Device

If Miravue devices are being utilized for IR or RS-232 port routing, you must set them up as expansion devices.

Select the processor in the system tree and then “Expansion Devices” in the partition to the right. Next, select

“Add Expansion Device” and select “VIP-1” from the list of expansion devices available.

An “Edit VIP-1” popup window will appear. For easier identification, it is recommended to name the Miravue

device the same or similar to the project file. Select the MAC radio button and enter the MAC Address you will

find on the label at the bottom side of the VIP-1 unit.

6 | Page

01/2019

RTI | Miravue VIP-1 Manual

Continue to add expansion devices as needed, repeating the process as described. Miravue devices will now

be available as a routable MPIO or RS-232 port when adding devices in the software.

7 | Page

01/2019

RTI | Miravue VIP-1 Manual

3) Miravue VIP-1 Programming Options

When programming the Miravue driver, there are many macro options available.

Select Source From List

Each display has scrolling source list capability. This command can

be used to select a source from that scrolling last.

Select Source

Used to select a source connected to a display or a Miravue device

being used as a transmitter for a source.

Open Media Stream

Open an RTSP feed by specifying the RTSP path, user and

password. Select the display and RTSP path to open the stream.

Close Media Stream

Close a current RTSP feed. Select a display that is broadcasting the

RTSP stream.

Play/Pause/Toggle Media

Stream

Play, pause or toggle the current stream broadcasting from a

display.

Send Message to Display

A message can be programmed in a macro that will send a

message to any or all displays. Select the display and type a

corresponding message.

8 | Page

01/2019

RTI | Miravue VIP-1 Manual

Each Miravue device comes with several variables that can be used to poll a device and provide two-way

feedback.

Button State / Text Feedback

Button State / Reversed and Visible States

Object-based Feedback (2-way scrolling lists)

9 | Page

01/2019

RTI | Miravue VIP-1 Manual

4) The RTI | Miravue VIP-1 Web Interface

The settings that should be adjusted via the web interface are dependent on whether the VIP-1 will be used

with an RTI control system or not.

IMPORTANT NOTE: If an RTI control system is used, the VIP-1 settings are configured via the two-way driver in

the Integration Designer programming software and will overwrite settings made via the web interface.

Web Interface Settings:

•When using an RTI control system: WiFi settings, Audio Offset.

•Without an RTI control system: All VIP-1 settings are configured via web interface.

a. Accessing the Setup Web Interface

Wired

From a web browser, enter the VIP-1 transceiver's IP

address (displayed on a TV via the HDMl-out port). If no

DHCP server is found, the transceiver assigns a default IP

address. Before entering the IP address, make sure the

connecting device is configured to the same network

segment (e.g., IP range, subnet mask, gateway, etc.)

Default IP address: 192.168.8.1

Note:

If the VIP-1 transceiver's IP address is later configured

outside the IP range of the connected device (laptop,

tablet etc), the LAN settings must be re-configured to

the same network segment before continuing. If the

network settings cannot be determined, pressing the

“DEFAULT” button for 10 seconds on the VIP-1 will

reset unit back to the factory default, and the

networking will be set to DHCP.

VIP-1 HDMI Output Displayed on TV/Monitor

10 | Page

01/2019

RTI | Miravue VIP-1 Manual

Transceiver Info

Serial: Product serial number

MAC address: Unique network identifier; can be

used by a DHCP server to assign a specific IP address

Firmware: Software version number

Hardware: Hardware version number

Important: The serial number, firmware version

number, and hardware version number are required

to obtain customer support

b. HDMI Configuration

HDMI Out

Enter a unique name for the video display device

connected to the HDMI-out port on the transceiver

(typically a location like Family-TV).

HDMI In

Enter a unique name for the video source device

connected to the HDMI-in port on the transceiver (e.g.

Blu-ray). This name is used in the on-screen source list.

Andere Handbücher für Miravue VIP-1

Inhaltsverzeichnis

Andere RTI Netzwerk-Hardware Handbücher

RTI

RTI ZB-Pro Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung