Ruckus Wireless T610s Bedienungsanleitung

Published June 2016, Part Number 800-71242-001 Rev A Page 1 of 4

T610s Access Point

Quick Setup Guide

This Quick Setup Guide provides step-by-step instructions on how to

field-install the Ruckus Wireless T610s access point (AP).

For detailed information on planning the installation, performing a site

survey, and operating the T610s, refer to the ZoneFlex Outdoor

Access Point User Guide, available at https://

support.ruckuswireless.com.

WARNING: Only trained and qualified personnel should be allowed to

install, replace, or service this equipment.

WARNING: Installation of this equipment must comply with local and

national electrical codes.

CAUTION: Make sure that you form a 80mm - 130mm (3”-5”) drip

loop in any cable that is attached to the AP or the building. This will

prevent water from running along the cable and entering the AP or the

building where the cable terminates.

CAUTION: Be sure that grounding is available and that it meets local

and national electrical codes. For additional lightning protection, use

lightning rods and lightning arrestors.

CAUTION: Make sure that proper lightning surge protection

precautions are taken according to local electrical code.

WARNING: Ruckus Wireless strongly recommends that you wear eye

protection before mounting the T610s.

THIS GUIDE IN OTHER LANGUAGES

请从以下网站获得该指南的简体中文版

https://support.ruckuswireless.com.

Vous trouverez la version française de ce guide à l'adresse suivante

https://support.ruckuswireless.com.

このガイドの⽇本語版は https://support.ruckuswireless.com

でご覧ください。

이가이드의 한국어 버전은 웹사이트

(https://support.ruckuswireless.com)에서 확인하시기 바랍니다 .

Veja a versão em português (Brasil) deste guia em

https://support.ruckuswireless.com.

Puede ver la versión en español (América Latina) de esta guía en

https://support.ruckuswireless.com.

BEFORE YOU BEGIN

Before deploying your Ruckus Wireless T610s, verify that all items

listed in Package Contents are included in the package. If any item is

damaged or missing, notify your authorized Ruckus Wireless sales

representative. Also, make sure that you have the required hardware

and tools.

REQUIRED HARDWARE AND TOOLS

• Customer-supplied outdoor-rated three-wire (1-2mm2or 14-

18AWG) AC cable

• 1/2” (13mm) flat-blade screwdriver or equivalent

• No. 2 Phillips screwdriver

• Small flat-blade screwdriver

• Torque wrench or torque screwdriver with sockets

• Long-nose pliers

• Electrical wire stripping and terminal crimping pliers

• Pipe or pole --OR-- a sturdy flat surface

• Electric drill with drill bits and customer-supplied wall anchors, flat

washers, and hex nuts for flat-surface mount

• Four factory-supplied 1/2” (12.7mm) wide stainless steel

adjustable clamps, 2.5” (63.5mm) diameter, for main mounting

bracket on smaller poles

•Ruler

PACKAGE CONTENTS

A complete T610s field installation package includes all of the items

listed below (see Figure 1for illustrations):

• T610s Access Point (A)

• Two M25 data cable glands (B)

• Ground wire with lug (C)

• Service Level Agreement/Limited Warranty Statement

• Declaration of Conformity

• Regulatory Statement

• Ruckus Wireless AP Getting Started Guide

• This Quick Setup Guide

Figure 1: Package Contents

NOTE: The outdoor AP Mounting Bracket and security cable are

optional accessories that must be purchased separately.

CAUTION! The minimum software revision for the T610s

is ZoneDirector (ZD) 9.13.1 or later, or SmartZone (SZ) 3.4

or later, or standalone AP firmware 104.0 or later.

DO NOT CONNECT THE T610s TO A RUCKUS

WIRELESS ZONEDIRECTOR RUNNING 9.13 OR

EARLIER.

Published June 2016, Part Number 800-71242-001 Rev A Page 2 of 4

T610SSECTOR ANTENNA COVERAGE

The T610s 120-Degree Sector AP is best deployed where

internal-antenna beamforming can provide extended reach and

throughput to a 120-degree coverage area. See Figure 2 for the

azimuth coverage pattern, and see Figure 3 for the elevation

coverage pattern.

Figure 2: Typical AP sector azimuth plane coverage, top view

Figure 3: Typical AP sector elevation plane coverage, side view

STEP 1: CONNECTING AND SEALING THE RJ-45

CABLES

Connect and seal the RJ-45 cable(s) using the M25 data cable gland

as shown in Figure 5.

WARNING: Do not use any PoE injector not tested and approved by

Ruckus Wireless to power the T610s Access Point.

WARNING: Do NOT plug PoE in power into the non-PoE Port (see

Figure 4).

Figure 4: T610s bottom view

1Feed the end of the cable through the sealing nut, rubber O-ring,

clamping ring assembly and cable gland base as shown in Figure

Figure 5: RJ-45 cable and cable gland assembly

2Use a wide flat-blade screwdriver to remove the required (PoE IN)

blanking cap from the T610s.

3Connect the cable to the Ethernet port on the T610s.

4Tighten the cable gland base into the T610s chassis to 7 N.m or

62 in-lbs.

5Wrap the clamping ring assembly around the rubber O-ring. Make

sure that the clamping ring assembly fully encloses the rubber O-

ring.

6Seat the clamping ring assembly and rubber O-ring in the cable

gland base.

7Hand-tighten the sealing nut.

STEP 2: ATTACHING THE U-JOINT BRACKET TO THE

MOUNTING BRACKET

NOTE: The following mounting instructions require purchase of

optional accessories that are not included in the standard T610s

package. The outdoor AP Mounting Bracket and safety cable are

optional accessories that must be purchased separately.

1Position the U-joint bracket on the mounting bracket.

Figure 6: U-joint bracket attached horizontally to the mounting bracket

NOTE: Mount the U-joint bracket in any direction on the mounting

bracket, preferably to allow AP azimuth adjustments. Then the AP

bracket allows AP elevation adjustments.

2Use four 1/4-28 bolt and washer sets (A) to mount the U-joint

bracket (B) to the mounting bracket (C). Tighten the bolts to 9.5

N.m (7 ft-lbs).

3Continue with Step 3a: Attaching the Mounting Bracket to a

Flat Surface or Step 3b: Attaching the Mounting Bracket to a

Metal Pole.

STEP 3A: ATTACHING THE MOUNTING BRACKET TO A

FLAT SURFACE

1Place the mounting bracket at the location on the flat surface

where you want to mount the AP. Use the holes on the mounting

bracket as a template to mark the locations of the mounting

holes.

Figure 7: Mounting bracket flat surface holes

2Remove the mounting bracket from the flat surface.

3Drill holes required for the mounting hardware.

NOTE: The hardware required for mounting to a wall are not included

in the mounting kit.

4Attach the mounting bracket to the flat surface using the

mounting hardware.

Extended

120º Reach

Extended

30º Vertical

Beamwidth

10º - 20º Downtilt

Recommended for

Extended Coverage

Cable gland base

Clamping ring assembly

Rubber O-ring

Sealing nut

Published June 2016, Part Number 800-71242-001 Rev A Page 3 of 4

5Using the mounting hardware instructions, tighten the hardware to

secure the mounting bracket.

6Continue with Step 4: Mounting the Linkage Bracket to the U-

Joint Bracket.

STEP 3B: ATTACHING THE MOUNTING BRACKET TO A

METAL POLE

1Insert the open end of one steel clamp into the upper two slots on

the mounting bracket.

2Take the other steel clamp and insert it into the lower two slots on

the mounting bracket.

NOTE: The clamps can be daisy-chained together to accommodate

larger poles.

3Use the clamps to attach the mounting bracket to the pole.

Tighten the clamps to 3 N.m or 27 in-lbs, or per manufacturer’s

specifications.

Figure 8: Attaching the mounting bracket to a vertical pole

4Continue with Step 4: Mounting the Linkage Bracket to the U-

Joint Bracket.

STEP 4: MOUNTING THE LINKAGE BRACKET TO THE

U-JOINT BRACKET

The linkage bracket attaches to the U-joint bracket using an M8 bolt

and washer set. The linkage bracket is symmetrical, and either end

can be attached to the U-joint bracket.

NOTE: Make sure that linkage bracket is installed with its serrated

external-tooth lock washer on the inside of the U-joint bracket

flanges. This ensures that the azimuth adjustment does not

change.

1Loosely assemble the linkage bracket (A), the U-joint bracket (C),

one serrated external-tooth lock washer (B), and one M8 bolt

and washer set (D).

Figure 9: Attaching the linkage bracket to the U-joint bracket

2Set the azimuth required by the AP.

3Tighten the M8 bolt to 13.6 N-m (10 ft-lbs).

4Continue with Step 5: Attach the AP bracket to the linkage

bracket.

STEP 5: ATTACH THE AP BRACKET TO THE LINKAGE

BRACKET

Attach the AP bracket to the linkage bracket using the included bolt,

nut, lock washer, flat washer, serrated external-tooth washer shown in

Figure 10.

The AP bracket attaches to the linkage bracket using an M8 bolt and

washer set. The linkage bracket is symmetrical, and either end can be

attached to the AP bracket.

NOTE: Make sure that linkage bracket is installed with its serrated

external-tooth lock washer on the inside of the AP bracket flanges.

This ensures that the elevation adjustment does not change.

1As described in Step 4: Mounting the Linkage Bracket to the

U-Joint Bracket, loosely assemble the AP bracket (shown in

Figure 11), the linkage bracket (A in Figure 9), the second

serrated external-tooth lock washer (B in Figure 9), and the

second M8 bolt and washer set (D in Figure 9).

Figure 10: Attach the linkage bracket to the AP bracket

STEP 6: ATTACHING THE AP BRACKET TO THE

ACCESS POINT

1Place the AP bracket onto the back side of the AP so that the four

larger screw holes on the bracket align with the four screw holes

on the AP. Make sure that the end of the AP bracket with the

hoisting loop is on the same side as the AP PoE IN port.

Figure 11: Attaching the AP bracket to the AP

2Use four 0.5-inch x 0.250-28 hex bolts with split lock and flat

washer sets to mount the AP bracket to the AP. Tighten the bolts

to 2.5-3.0 N.m or 22-27 in-lbs.

CAUTION: Make sure that the screws are no longer than 0.5 inch.

If a screw is longer than 0.5 inch, it can damage the AP chassis.

3If required, suspend the AP by attaching a carabiner to the

hoisting loop on the AP bracket.

NOTE: This kit may include extra screws, nuts and washers. You

may use the extras wherever required.

4Continue with Step 7: Set the Elevation and Tighten Elevation

Bolt.

STEP 7: SET THE ELEVATION AND TIGHTEN ELEVA-

TION BOLT

1Set the elevation required by the AP.

2Tighten the M8 bolt to 13.6 N-m (10 ft-lbs).

STEP 8: EARTH GROUNDING THE AP

CAUTION: Make sure that earth grounding is available and that it

meets local and national electrical codes. For additional lightning

protection, use lightning rods and lightning arrestors.

NOTE: The color coding of ground wires varies by region. Before

completing this step, check your local wiring standards for

guidance.

• Using the factory-supplied ground wire and ground screw/

washer set, connect a good earth ground to the AP chassis

Published June 2016, Part Number 800-71242-001 Rev A Page 4 of 4

ground point (Figure 12).

CAUTION: The T610s AP includes one 12mm stainless steel

M6x1 earth ground screw with split lock and flat washers. Make

sure that any replacement screw is no longer than 12mm. If a

screw is longer than 12mm, it can damage the AP chassis.

Figure 12: Connect good earth ground to AP here

STEP 9: INSTALLING THE SECURITY CABLE

NOTE: The security cable is an optional accessory that must be

purchased separately.

1Thread the security cable through the mounting bracket (A) and

through the eye on the cable itself (B), as shown in Figure 13.

2Attach the safety cable to the AP (C) in Figure 13.

Figure 13: Attaching the security cable

Congratulations! You have mounted your T610s access point.

INSTALLING AUSB DONGLE

To install a USB dongle, which could be an IoT radio like BLE,

802.15.4, Z-wave or the like, remove the two 3mm hex screws,

remove the cap, and insert the dongle into the USB port. Once

installed, replace the cap and the hex screws, and torque the screws

to 7 in-lbs.

Figure 14: Installing a USB dongle

TROUBLESHOOTING

CAUTION: If required, you can reset the AP to its factory default

settings by pressing the reset button located inside the PoE IN

port. DO NOT DO THIS UNLESS SO INSTRUCTED. (Doing this

resets the AP IP address to 192.168.0.1.)

NOTE: After a reset, you can access the internal AP web interface

using https://192.168.0.1. Your device must use any

other address from 192.168.0.2 through 192.168.0.254, with

subnet mask 255.255.255.0. The username is super, and the

password is sp-admin. Refer to the ZoneFlex Outdoor Access

Point User Guide for information on configuring and operating the

AP. This document is available at https://

support.ruckuswireless.com.

NOTE: After an AP is removed from its mounting, it may drip

some water from the channel surrounding the radome. As long as

the AP has been operating normally, this incidental water

collection and dripping is normal, and is not service-affecting.

Andere Ruckus Wireless Drahtloser Zugangspunkt Handbücher

Ruckus Wireless

Ruckus Wireless R610 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless zoneflex t301n Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7762-T Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZF7762-AC Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless zoneflex t301s Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex series Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 2942 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7321 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7942-OT Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless R720 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex series Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless Unleashed R600 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless SmartCell Gateway 200 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7352 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless C110 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7372-E Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless T300 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7982 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless Unleashed R510 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZONEFLEX R310 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless T310c Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless H510 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex 7343 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless R320 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung