Rupp Air CFA-D150 Bedienungsanleitung

Ventilation Fan

CFA-D150

(BPT18-44A)

It is very important that you read this manual installation for your

safety and efficiency of the unit.

Please be advised that all units should be installed by a licensed electrician.

READ AND SAVE THESE INSTRUCTIONS

Table of Contents

Table of Contents..........................................................2

Safety Information.........................................................2



Pre-installation ..............................................................3

Planning Installation ................................................................3

Installation Options ..................................................................4

Tools required..........................................................................4

Materials required....................................................................4

Hardware Included........................................................5

Package Contents ....................................................................5

Installation ..................................................................... 6

Specifications ....... ....................................................... 9



.................................................9 

DIMENSIONS ........................9 

Safety Information

CFA-D150(BPT18-44A)

.............................................

1. Electric Service supply must be 120V

60Hz.

2. Follow all local safety and electrical codes as well as NEC (National Electrical Code) and the

OSHA(Occupational Safety and Health Act).

3. This unit must be properly grounded.

4. Always disconnect the power supply prior to servicing the fan, motor or junction box.

5. Do not bend or kink the power wires.

6. Do not install where the air temperature will exceed 40°

C(104°

F).

7. This ventilating fan is approved for use over abathtub or shower when installed in aGFCI

protected circuit.

8. Do not use to exhaust hazardous or explosive vapors.

9. Do not install in a cooking area.

10. Use this unit in the manner intended by the manufacturer. If you have any questions please call

the manufacturer .Customer service number located on last page.

11. Installation work must be carried out by qualified person(s) in accordance to all local and safety

codes including the rulers for fire-rated construction.

12. Sufficient air supply is required for proper combustion and the exhausting of gases through the

chimney(flue) of fuel burning equipment to prevent back –drafting .See the standards of NFPA

(National Fire Protection Association ) and ASHRAE(American Society for Heating Refrigeration

and Air Conditioning Engineers) and the local building code authorities.

13. Exercise care to not damage existing wiring when cutting or drilling into walls or ceilings.

14. Fans should always be vented to the exterior.

15. If this ventilating fan is installed over atub or shower, it must be marked as approved for the

application.

16. Prior to service or cleaning this unit, shut off power supply at the panel and lock to prevent the

power from being turned on. If the panel cannot be locked clearly mark the panel with awarning

tag not to turn on the power.

17. Do not install in a ceiling with insulation greater than R40.

18. Ductwork should be installed in a straight line with minimum bends.

19. Duct work size must be aminimum of the discharge and should not be reduced.

20.

For UL: the fan is intended to be mounted at least 2.1m(7feet) above the floor.

Care and Cleaning......................................................... 10

Pre-installation

PLANNING INSTALLATION

When installing the ventilation fan in a new construction site, install the main body of the fan and duct work during the rough‑in

construction of the building. The grill should be installed after the finished ceiling is in place.

When installing in existing construction, use the dimensions on page 12 to determine the required hole size for the ceiling. The grill edges

should overlap the finished ceiling.

NOTE: If installing in existing construction, you must

have access to space above and below the installation

location.

This unit will operate most quietly and efficiently when located where the shortest possible duct run and minimum number of elbows will be

needed.

Do not install the ventilation fan in areas where the duct work will require configurations as shown in the following figure:

Pre-installation (continued)

INSTALLATION OPTIONS

We recommend installing the ventilation fan by securing the main body of the fan against one ceiling joist and using the header bars as

necessary for support of the adjoining joist.

There are multiple installation configurations possible for this ventilation fan. Not all configurations are shown. If your installation requires a

variation other than those shown, consult with a licensed contractor to determine the best installation for your project. If you are replacing

an existing fan, ensure that the new grill will adequately cover the existing opening.

TOOLS REQUIRED

Hammer

Safety

goggles

Phillips

screwdriver Level

Electrical tape

Drill

MATERIALS REQUIRED

Duct vent

Duct

clamp Duct tape

Duct piping

Pre-installation (continued)

HARDWARE INCLUDED

NOTE: Hardware not shown to actual size.

Part Description Quantity

AA Long wood screw (M4x30) 8

BB Short screw (M4x12) 2

CC Short screw (M4x8) 1

PACKAGE CONTENTS

Part Description

Fanbody

B Grill

C Suspension bracket I

D Suspension bracket II

E Suspension bracket III

AA BB CC

Installation

1 Determining joist width

□ Measure the distance from the center of the two ceiling

joists where you will be installing the ventilation fan.

2 Suspension bracket installation 3 Joint installation under 20 in.

□ For ceiling joist installations under 20 in., insert

suspension bracket I (C) into the fan body (A).

Proceed to step 4.

□ For ceiling joist installations between 20 in. and 24

in., insert suspension brackets I (C), II (D), and III

(E). Proceed to step 5.

NOTE: Sliding hanger bars are provided to allow for

accurate positioning of the main body between joists.

□ Use four long wood screws (AA) to attach the main

body of the fan to the ceiling joists.

□ Ensure the main body is level and square to the

joists.

□ Tighten all screws.

CAUTION: Do not mount the fan flush against the joist. The

flange should be flush with the ceiling board.

□

Use screw(CC) to secure the suspension

□

Use screws (BB) to secure the supension

bracket(C).

bracket(D and E).

Installation (continued)

4 20 – 24 in. joist installation 5 Duct connection

□ Use long wood screws (AA) to loosely attach the

main body of the fan to one ceiling joist.

□ Extend the hanger bars to the opposite ceiling joist.

□ Secure the suspension brackets (C, D, and E) to

the joist using long wood screws (AA).

□ Ensure the main body is level and square to the

joists.

□ Tighten all screws.

CAUTION: Do not mount the fan flush against the joist. The

flange should be flush with the ceiling board.

□ Install a circular duct (1) to the outlet and secure

□ Install the duct with a gradient of 1˚ ~ 2˚ to the

outside.

it with duct tape or clamps to the outlet.

Installation (continued)

6 Connecting wiring from unit to

house 7 Mounting the grill

WARNING: Make sure that the main power is off.

WARNING: Failure to wire this product correctly could result

in electrical shock, fire hazards, or damage to the product.

Consult a licensed electrician if you are unsure of your ability

to correctly install wiring.

CAUTION: If your house wires do not match these colors,

determine what each house wire represents before

connecting. You may need to consult a licensed electrician to

determine this safely.

□ Connect house wires to ventilation fan wires.

□ Match colors as shown (black to black, white to

white, and green to green) using wire nuts (not

provided).

□ Replace the junction box cover. Do not pinch the

lead wires.

□ Use the spring clips to pinch mount and insert the

grill (B) into the narrow rectangular slots inside of

the fan housing next to the fan motor.

(black)to switch

(white)to neutral

(green)to ground

Junction Box

Automatic Terminal

Capacitator

Motor

Specifications

CFA-D150(BPT18-44A)

Model No. CFA-D150(BPT18-44A)

Air direction 150 cfm

oltage 120

Hertz 60 HZ

Duct diameter 6 in. (15.24 cm)

Noise 1.5 Sone

Power consumption (Watts) 42 W

Speed 660 rpm

Air deliver at 0.1" WG 150 cfm

Weight 10.78 lbs. (4.9 kg)

DIMENSIONS

Ceiling opening - length 10.8 in. (27.4 cm)

Ceiling opening - width 10.5 in. (26.7 cm)

Ceiling opening - depth 8.5 in. (21.6 cm)

Housing dimension - length 10.2 in. (25.9 cm)

Housing dimension - width 10.2 in. (25.9 cm)

Housing dimension - depth 8.0 in. (20.30 cm)

Care and Cleaning

□ Before servicing or cleaning the unit, disconnect the power supply at the panel and lock to prevent the power from being turned

on. If the panel cannot be locked, clearly mark the panel with a warning tag to prevent the power from being turned on.

□ Remove the grill by squeezing the springs and pulling the grill down.

□ Wash and clean the grill in a sink and dry with a cloth.

□ Remove dust and dirt from the fan housing with a vacuum cleaner.

□ Dampen a cloth with dish detergent, wipe the fan housing and dry with a cloth.

□ Replace the grill.

□ To reduce the risk of fire, always vent fans to the exterior and in compliance with local codes. Do not vent exhaust air into spaces

within walls, ceilings, attics, crawl spaces, or garages.

□ Unplug or disconnect the appliance from the power supply before servicing.

CAUTION: Do not use solvents, thinner or harsh

chemicals for cleaning the fan..

CAUTION: Do not allow water to enter the motor

CAUTION: Do not immerse resin parts in water over 140°

F (60° C).

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Rupp Air Lüfter Handbücher

Rupp Air

Rupp Air CFA-D90 Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Hinkley

Hinkley HIGHLAND Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung