Russell Hobbs RHOMF8 Installationsanleitung

INSTRUCTIONS & WARRANTY

MODEL NO: RHOMF8

RUSSEL HOBBS OUTDOOR MIST FAN

Congratulations on purchasing our Russell Hobbs Outdoor Mist Fan. Each unit is

manufactured to ensure safety and reliability. Before using this appliance for the first time,

please read the instruction manual carefully and keep it for future reference.

FEATURES OF RUSSELL HOBBS OUTDOOR MIST FAN

1. 18’’ Outdoor mist fan

2. Suitable for domestic use only

3. Humidifier with 7L water tank

4. Generates mist for up to 5,5 hours

5. 4 Speed settings

6. Oscillating function

7. Castors for ease of movement

8. 3 Large industrial blades

9. Overheat protection

10. 230W

IMPORTANT SAFEGUARDS

When using any electrical appliance, basic safety precautions should always be followed

including the following:

1. Please read the instructions carefully before using any appliance.

2. Use the fan only for purposes described in the instruction manual.

3. Always ensure that the voltage on the rating label corresponds to the mains

voltage in your home.

4. Incorrect operation and improper use can damage the appliance and cause

injury to the user.

5. The appliance is intended for household use only. Commercial use

invalidates the warranty and the supplier cannot be held responsible for injury

or damage caused when using the appliance for any other purpose than that

intended.

6. This appliance is not intended for use by persons (including children) with

reduced physical, sensory or mental capabilities, or lack of experience and

knowledge, unless they have been given supervision or instruction

concerning use of the appliance by a person responsible for their safety.

7. Avoid any contact with moving parts.

8. To reduce the risk of fire or electric shock, do not use this fan with any solid-

state speed control device.

9. To protect against electrical shock, do not immerse the fan, plug or cord in

water or any other liquid or spray with liquids.

10. Children should be supervised to ensure that they do not play with the

appliance

11. Close supervision is required when any appliance is used near or by children,

pets and invalids.

12. Check the power cord and plug regularly for any damage. If the cord or the

plug is damaged, it must be replaced by the manufacturer or a qualified

person in order to avoid an electrical hazard.

13. Do not operate the fan in the presence of explosive and/or flammable fumes.

14. Do not use the appliance if it has been dropped or damaged in any way. In

case of damage, take the unit in for examination and/or repair by an

authorised service agent

15. Place the fan on a dry level surface

16. Do not hang or mount fan on a wall or ceiling

17. Remove the plug from the socket by gripping the plug. Do not pull on the cord

to disconnect the appliance from the mains. Always unplug the fan when not

in use, before cleaning or when adding or removing parts.

18. The use of accessory attachments that are not recommended or supplied by

the manufacturer may result in injuries, fire or electric shock.

19. A short cord is provided to reduce the hazards resulting from becoming

entangled in or tripping over a longer cord.

20. Do not allow the cord to touch hot surfaces and do not place on or near a hot

gas or electric burner or in a heated oven.

21. Use of an extension cord with this appliance is not recommended. However, if

it is necessary to use an extension lead, ensure that the lead is suited to the

power consumption of the appliance to avoid overheating of the extension

cord, appliance or plug point. Do not place the extension cord in a position

where it can be pulled on by children or animals or tripped over.

22. This appliance is not suitable for outdoor use. Do not use this appliance for

anything other than its intended use.

23. Do not carry the appliance by the power cord.

24. Do not leave this appliance unattended during use. Always unplug the unit

when not in use or before cleaning.

25. Always operate the appliance on a smooth, even, stable surface. Do not

place the unit on a hot surface.

26. Ensure that the switch is in “Off” position after each use.

19"

20"

27. The manufacturer does not accept responsibility for any damage or injury

caused by improper or incorrect use, or for repairs carried out by

unauthorised personnel.

28. In case of technical problems, switch off the appliance and do not attempt to

repair it yourself. Return the appliance to an authorised service facility for

examination, adjustment or repair. Always insist on the use of original spare

parts. Failure to comply with the above mentioned pre-cautions and

instructions, could affect the safe operation of this appliance.

29. Do not touch/ pull out/ put back the water tank when the unit is plugged into

the power source. Make sure it is physically disconnected from the mains

before you do anything with the water tank.

30. When the water level is too low, the safety switch will stop the operation of the

mist function, unplug the unit and refill the water tank for further operation.

31. Do not let dust or other substances collect on the mist plate – if the outlet is

blocked, the mist function will fail to function normally.

32. Before cleaning the unit, make sure that it is completely disconnected from

the plug. Make sure your hands are not wet when unplugging the unit.

33. Do not use hot water in the water tank.

34. Do not add any chemicals, oils or other additives to the water tank.

PARTS DIAGRAM

1. Mist outlet

2. 18 inch front fan guard

3. Screw

4. 18 inch AL blades

5. Iron belt

6. M6 screw

7. 18 inch rear fan guard

8. Motor

9. Wire box

10. Wire

11. M5 screw

12. Fan body

13. Base

14. M8 screw

15. Wheel

16. Screw

17. Hose

18. Buckle

19. Screw

20. Tube

ASSEMBLY INSTRUCTIONS

1. Assemble the wheel (15) to the base (13) with the screw.

2. Assemble the fan body (12) and fit it to the base (13) with a screw (14).

3. Connect the internal wires (10) to motor assembly (8). Connect the wire box

(9) to the fan body (12) and then assemble the motor (8) to the fan body (12)

with the screws (11).

4. Assemble the rear fan guard (7) to the motor (8).

5. Assemble the blades (4) onto the motor (8).

6. Fasten the mist outlet (1) on the front fan guard (2) and then fasten the fan

guard (2) and (7) with the iron belt (5) and buckle (18).

7. Insert the hose (17) into the mist outlet (1) and insert the other side to the fan

body (12).

8. Fasten the tube (20) to the body with the screw (19).”

BEFORE FIRST USE

1. First ensure that the body is attached to the base.

2. The fan head must be fixed to the main part of the structure pole.

3. Install the back fan guard to the motor housing, slide on aluminum blades and

ensure the screw is tightened.

OPERATING INSTRUCTIONS

Place the water tank on a flat surface and fill with water as per below steps：

1. Remove the mist tank on upper side , the mist function will be cut off automatically

when the water tank is removed from the body

2. Pour the water into the water tank.

3. Ensure that the water level does not reach be beyond the max indication.

4. After filling the water, close the mist cask and connect the mist tube.

Attention: Please check carefully to ensure the tank is not overfilled and there is no water

running down the back side of the tank.

1. Oscillation switch

2. Mist button

3. Speed button

4. Angle adjustment lock nut

5. Insert the plug into the socket and turn on the fan, choose the function button to

select the fan speed accordingly.

6. Speed button (3)：Operate this button and choose the fan speed level 1,2,3,4

7. Turn on mist switch (2); the mist will spray out from the mist outlet, “the mist” function

can be used separately or in conjunction with the fan. If the mist function is used

separately, it will increase the humidity in the air.

8. Switch on the oscillation switch (1), to change the wind direction. Switch off again to

stop oscillation.

9. Angle adjustment: Adjust the fan guard direction to move the wind angle of the fan. If

necessary slacken the lock nut (4) with a spanner, change the angle and then tighten

the nut again

CLEANING AND MAINTANACE

1. Screw

2. Overflow gap

3. Water release hole

4. Shell

5. Water tank

6. Mist tank

7. Upper water outlet

8. Lower water outlet

9. Max water level

10. Wind outlet

11. Mist maker

12. Cleanser

13. Mist disk

14. Brush

Before cleaning, turn the unit off, unplug from the power supply and wait for the unit to cool

down.

1. To clean the unit use a soft cloth to wipe off any dust.

2. Clean the water tank every two or three weeks, and clean the flume every week.

3. Remove the plastic tube from mist tank and remove the water tank to clean it.

4. Open the tank cover, use dry cloth to clean the mist tank or use mild detergent to

clean the mist tank if it has mineral water residue.

5. Please add a few drops of lubricant to the motor shaft after cleaning it to extend

motor life.

Keep the unit in a cool and dry place when not to be used for a long time.

CAUTION: Unplug fan from the electrical supply source before cleaning. After servicing, any

safety device (including grilles and blades) it must be reinstalled or remounted as previously

installed. Use soft damp cloth then wipe with dry cloth. Do not use harmful detergents. Do

not bend the blades.

STORING THE APPLIANCE

• Unplug the unit from the wall outlet and clean all the parts as instructed above.

Ensure that all parts are dry before storing.

• Store the appliance in its box or in a clean, dry place.

• Never store the appliance while it is still wet or dirty.

SERVICING THE APPLIANCE

There are no user serviceable parts in this appliance. If the unit is not operating correctly,

please check the following:

• You have followed the instructions correctly

• That the unit has been wired correctly and that the wall socket is switched on.

• That the mains power supply is ON.

• That the plug is firmly in the mains socket.

If the appliance still does not work after checking the above:

- Consult the retailer for possible repair or replacement. If the retailer fails to resolve the

problem and you need to return the appliance, make sure that:

• The unit is packed carefully back into its original packaging.

• Proof of purchase is attached.

• A reason is provided for why it is being returned.

If the supply cord is damaged, it must be replaced by the manufacturer or an authorised

service agent, in order to avoid any hazard. If service becomes necessary within the

warranty period, the appliance should be returned to an approved Home Of Living Brands

(Pty) Limited service centre. Servicing outside the warranty period is still available, but will,

however, be chargeable.

CHANGING THE PLUG

Should the need arise to change the fitted plug, follow the instructions below.

This unit is designed to operate on the stated current only. Connecting to other power

sources may damage the appliance. Connect a three-pin plug as follows:

The wires in this mains lead are

coloured in accordance with the

following code:

Green/Yellow = Earth

Blue = Neutral

Brown = Live

10"

PLEASE AFFIX YOUR PROOF OF PURCHASE/RECEIPT HERE

IN THE EVENT OF A CLAIM UNDER WARRANTY THIS RECEIPT MUST BE

PRODUCED.

W A R R A N T Y

6. Home Of Living Brands (Pty) Limited warrants to the original purchaser of this

product (“the customer”) that this product will be free of defects in quality and

workmanship which under normal personal, family or household use and purpose

may manifest within a period of 1 (one) year from the date of purchase (“warranty

period”).

7. Where the customer has purchased a product and it breaks, is defective or does

not work properly for the intended purpose, the customer must notify the supplier

from whom the customer bought the product (“the supplier”) thereof within the

warranty period. Any claim in terms of this warranty must be supported by a proof

of purchase. If proof of purchase is not available, then repair, and/or service

charges may be payable by the customer to the supplier.

8. The faulty product must be taken to the supplier's service centre to exercise the

warranty.

9. The supplier will refund, repair or exchange the product in terms of this warranty

subject to legislative requirements. This warranty shall be valid only where the

customer has not broken the product himself, or used the product for something

that it is not supposed to be used for. The warranty does not include and will not

be construed to cover products damaged as a result of disaster, misuse, tamper,

abuse or any unauthorised modification or repair of the product.

10. This warranty will extend only to the product provided at the date of the purchase

and not to any expendables attached or installed by the customer.

11. If the customer requests that the supplier repairs the product and the product

breaks or fails to work properly within 3 (three) months of the repair and not as a

result of misuse, tampering or modification by or on behalf of the customer, then

the supplier may replace the product or pay a refund to the customer.

12. The customer may be responsible for certain costs where products returned are

not in the original packaging, or if the packaging is damaged. This will be

deducted from any refund paid to the customer.

HOME OF LIVING BRANDS (PTY) LTD

www.homeoflivingbrands.co.za

011 490-9600 (Jhb)

031 303-1163 (Dbn)

021 552-5161 (CT)

www.russellhobbs.co.za

www.facebook.com/RussellHobbsSA

Inhaltsverzeichnis

Andere Russell Hobbs Lüfter Handbücher

Russell Hobbs

Russell Hobbs RHMF18 Installationsanleitung

Russell Hobbs

Russell Hobbs RHPDF0911 Bedienungsanleitung

Russell Hobbs

Russell Hobbs RHTF3201 Bedienungsanleitung

Russell Hobbs

Russell Hobbs RHMF40 Installationsanleitung

Russell Hobbs

Russell Hobbs RHMP01 Installationsanleitung

Russell Hobbs

Russell Hobbs RHMDF1211CH Bedienungsanleitung

Russell Hobbs

Russell Hobbs RHPF-40 Installationsanleitung

Russell Hobbs

Russell Hobbs RHFF56 Installationsanleitung

Russell Hobbs

Russell Hobbs RHMPF4 Installationsanleitung

Russell Hobbs

Russell Hobbs RHPF-40 Installationsanleitung

Russell Hobbs

Russell Hobbs SCANDI Bedienungsanleitung

Russell Hobbs

Russell Hobbs RHDF 30 Installationsanleitung

Russell Hobbs

Russell Hobbs RHPPF1611 Bedienungsanleitung

Russell Hobbs

Russell Hobbs RHHV45 Installationsanleitung

Russell Hobbs

Russell Hobbs RHPDF1211 Bedienungsanleitung

Russell Hobbs

Russell Hobbs RHDF 30 Installationsanleitung

Russell Hobbs

Russell Hobbs RHMF10 Bedienungsanleitung

Russell Hobbs

Russell Hobbs RHTF1401 Bedienungsanleitung

Russell Hobbs

Russell Hobbs SCANDI Bedienungsanleitung

Russell Hobbs

Russell Hobbs RHHV50 Installationsanleitung

Russell Hobbs

Russell Hobbs RTF-40 Installationsanleitung

Russell Hobbs

Russell Hobbs RHDF12 Installationsanleitung

Russell Hobbs

Russell Hobbs RHOFF18 Bedienungsanleitung

Russell Hobbs

Russell Hobbs RHMPF1611CH Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung