RVR Solar TEX-LCD Series Bedienungsanleitung

/TLC

Additional Manual for

TEX-LCD series

and TEX-LIGHT series

Manufactured by Italy

/TLC - Additional Manual

Version 1.0

R.V.R. Elettronica SpA

Via del Fonditore 2/2c - 40138 - Bologna (Italia)

Phone: +39 051 6010506

Fax: +39 051 6011104

Email: info@rvr.it

Web: www.rvr.it

Printed and bound in Italy. No part of this manual may be reproduced,

memorized or transmitted in any form or by any means, electronic

or mechanic, including photocopying, recording or by any informa-

tion storage and retrieval system, without written permission of the

File Name: 03_TLC_ING_1.0.indd

Version: 1.0

Date: 01/02/2008

Revision History

Date Version Reason Editor

01/02/2008 1.0 Prima Edizione J. H. Berti

/TLC

iUser Manual Rev. 1.0 - 01/02/08

Table of Content

1. General Description 1

1.1 Remote alarm monitoring 1

1.2 Telemetry 3

1.3 Remote control 3

2. Remote Alarm Reporting Conguration 5

3. TEX-LCD/TLC External Description 9

3.1 Rear Panel TEX-LCD (2 HE) 9

3.2 Rear Panel TEX-LCD (3 HE) 11

/TLC

ii User ManualRev. 1.0 - 01/02/08

This page was intentionally left blank

/TLC

1 / 12User Manual Rev. 1.0- 01/02/08

1. General Description

The telemetry option, whether internal or external, supports connectivity to the

whole range of units of RVR’s TEX-LCD and TEX-LIGHT family of products.

This section describes the features introduced with /TLC version (option with

external telemetry without modem) and the necessary steps for their proper

conguration.

The telemetry option supports:

Remote alarm reporting by sending SMS messages through a GSM modem

or through a PSTN modem (dial-up) by sending an alarm message string to a

connected PC.

Telemetry, with all equipment parameters sent to the “TELECON” software

through an RS232 connection.

Remote controlling through an RS232 connection to the “TELECON” software

or through certain predetermined SMS messages if an external GSM modem

is connected.

Telemetry on internet across 10Base-T LAN/Ethernet network through TCP-IP

-INT/TEX external interface connection.

1.1 Remote alarm monitoring

Alarm generation parameters are listed below:

Exciter output power (forward power good “PgD”);

Reected power at the exciter (reected power good “PgR”);

Temperature state (OVER TEMPERATURE);

Audio Signal Level;

Mains voltage state (present or missing).

Factory default settings are as follows:

ALARM TIME THRESHOLD

Forward Power (Fwd Pwr) 25 Sec. Power Good (PgD)

Reflected Power (Rfl Pwr) 25 Sec. Power Good (PgR)

Audio 325 Sec. 20 kHz

Over Temperature 25 Sec. 72°C

Mains Power (Mains) 25 Sec.

Table 1.1

An inhibit time (start time) after power-on is provided to ensure false alarm

prevention. When this inhibit time times out, the thresholds of alarm generation

parameters are checked and remote alarms are sent if needed.

Alarm generation technique is outlined in the gure below; remote alarm delay, i.e.

the amount of time the system waits before issuing a remote alarm after an alarm

condition occurs is indicated in table 1.1. When appropriate, a new line is added

to the alarm log stored in /TLC, up to six lines maximum.

•

/TLC

2 / 12 User ManualRev. 1.0 - 01/02/08

Figure 1.1

The alarm log may be reviewed using the “TELECON” software or through SMS

(see relevant section).

WARNING: The mains alarm is triggered from the battery charger board; as a result,

this board is required even when no batteries are installed. In the conguration

without batteries, no alarm is generated; instead, an SMS message indicating a

normal condition is sent upon next start-up.

When any one of the parameters listed above changes state, a text message with

the following information is sent via modem (if tted):

Station Name.

Station ID.

State of measurements.

EX1.

TLC ID:01-Station Name-

Fwd Power OK-

RFL Power OK-

Over Temp OK-

Audio OK-

Mains OK-

EX2.

TLC ID:01-Station Name-

Alarm Fwd Power-

RFL Power OK-

Over Temp OK-

Alarm Audio -

Alarm Mains -

•

/TLC

3 / 12User Manual Rev. 1.0- 01/02/08

1.2 Telemetry

Equipment telemetry consists in the remote monitoring of all operating parameters

and can only be achieved through serial cable or modem connection to the

“TELECON” software.

1.3 Remote control

When the exciter is connected to the internal telemetry unit, it can be controlled

from a PC.

Fig.1.2: Example of Modem-to-PC connection

The “TELECON” software establishes connection with the station and enables the

following remote operations: alarm reset, transmitter power on/power off, power

supply reduction, dummy load testing, etc., data evaluation to locate possible

faults, identication of parts required for repair.

An alternative remote controlling option uses SMS messaging through a common

GSM phone (if connected with an external GSM modem), in which case the

equipment will respond as indicated in table 1.2.

Before querying the system using SMS messages, establish a connection using

the “TELECON” software and set the provider service centre number and the

telephone numbers authorised to send these commands to the devices.

/TLC

4 / 12 User ManualRev. 1.0 - 01/02/08

The internal and external telemetry options support the following commands:

Command Response Description

INFO

Station: “station name”-

ID: “station identifier”-

FWD: “absolute value”-

RFL: “absolute value”-

Temp: “absolute value”-

TX On (or TX Off)-

Alarm Present / Alarm Absent

Transmitter status

information

INFO1

Alarm SMS message

Forces the transmission of

an alarm SMS msg

TXON

Station: “station name”-

ID: “station identifier”-

TX is On -

Transmitter power-on

TXOFF

Station: “station name”-

ID: “station identifier”-

TX is Off -

Transmitter power-off

ALARM

Station: “station name”-

ID: “station identifier”-

Alarm: “Alarm log”

Alarm log

RESET

Station: “station name”-

ID: “station identifier”-

ALARM RESET OK-

Clear Alarm Log

RESMOD

-- none --

Resets and re-initialises

modem

Table 1.2

Note: Response time to SMS commands may vary with different GSM network

providers; as a general rule, response time should not exceed 7-10 minutes

maximum.

/TLC

5 / 12User Manual Rev. 1.0- 01/02/08

 2. RemoteAlarmReportingConguration

Firstly, you will have to set certain parameters in the (internal or external) telemetry

option using the “TELECON” software. Connect the PC serial port COM to the

RS232 connector on the rear panel of the /TLC option using a standard Male DB9

- Female DB9 serial cable.

Fig.2.3: Example of connection between TEX-LCD unit with /TLC option and PC

When using the “TELECON” software for the rst time, select the station and then

enter:

COM port used,

Baud rate (set to 9600),

type of connection (set to direct, via cable).

When you have entered the correct data, click the “Start” button to conrm and

the “TELECON” main screen appears, as shown in the gure:

•

/TLC

6 / 12 User ManualRev. 1.0 - 01/02/08

Use this screen to change Start time. To edit this parameter, click the “TStart” box

with the left mouse button (default setting is 300sec., the equivalent of 5 min.); this

opens a window where you can change the setting. Press Enter to conrm.

Double click the green label in the top left corner of the TELECON screen and

select “Eeprom” (as shown in the gure below).

In the open menu, press this key to view station parameters.

Select the “General” data category and set the 5 parameters:

STATION ID: Station identier;

STATION NAME: (max 18 characters);

•

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere RVR Solar Sender Handbücher

RVR Solar

RVR Solar BLUES30NV Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung