Saddlebrook BarnCams TrailerCam Bedienungsanleitung
TrailerCam
Instructions
Camera Setup Instructions
Here is your camera and transmitter.
(Actual camera may vary.)
Here is your receiver.
Step One:Mount the camera in a good
location to view your animals. You can
adjust the set screw on the bracket to lock the
camera into place. Run the cables from the
camera to the outside of the trailer where the
transmitter will be mounted.
Step Two:Mount the transmitter on the
outside of your trailer with the BarnCam
label side facing up. Try to mount it so that
there is a direct line of sight to where you will
be viewing your camera on your screen. The
wires coming out of the transmitter should
not point up. Most often it is hard wired into
a light connection, etc. Please use caution to
determine which wire is positive (white wire
is positive).
Step Three:Set up the receiver by flipping
up the antenna and facing the flat side to the
transmitter. It does not turn 360 degrees so
be careful not to break it. Plug in the power
supply to the back of the receiver. You can
adjust the camera number by pressing the
channel button. Your first camera will be set
to one, and so on.
This kit is made up of three main parts. Part one is the
camera, power adapter, mounting hardware and cable.
Part two is the transmitter and power adapter. Part
three is the receiver, power adapter and cables.
Your camera system was thoroughly tested prior to
shipment. Please set everything up inside your
car/house before installing outside to ensure
nothing was damaged during shipment.
Setting up LCD Receiver
1. Press POWER KEY to turn power on. (indicator lit up)
2. Press CH KEY to select desired channel.
(Channel number displays on right upper corner screen)
3. Press VOLUME up/down key for desirable volume.
4. Manual Mode:
Brightness Setting -- Press Function Key once.
Screen
will display BRIGHTNESS, then press VOLUME
up/down key to adjust BRIGHTNESS.
Contrast Setting -- Press Function Key twice.
Screen will display CONTRAST, then press VOLUME
up/down key to adjust CONTRAST.
Color Setting -- Press Function Key three times.
Screen will display COLOR, then press VOLUME
up/down key to adjust COLOR.
5. Press AUTO KEY to select manual or auto channel
switching. (with auto switching selection, "auto" will
appear on the right bottom screen)
6. Auto Mode: After pressing AUTO KEY
a. Auto Channel Switching -- Press FUNCTION KEY
once, screen will display Mode 1, then press VOLUME
up/down key to select preferred auto switching sequence:
Mode 1: channel 3.4
Mode 2: channel 1.2
Mode 3: channel 1.2.3
Mode 4: channel 1.2.3.4
b. Dwell Time -- Press FUNCTION KEY twice, screen
will display TIMER 2 S, then press VOLUME up/down
key to select auto switching dwell time (TIMER 2 S:
indicates channels will switch every 2 seconds). Dwell
time can be set from 2 to 9 seconds.
c. Brightness Setting -- Press FUNCTION KEY three
times, screen will display BRIGHTNESS, then press
VOLUME up/down key to adjust BRIGHTNESS.
d. Contrast Setting -- Press FUNCTION KEY four times,
screen will display CONTRAST, then press VOLUME
up/down key to adjust CONTRAST.
e. Color Setting -- Press FUNCTION KEY five times,
screen will display COLOR, then press VOLUME
up/down key to adjust COLOR.
When setting is complete, the screen will return to original
display after five seconds. The channel/mode/timer setting
will be stored as a default setting even after the LCD
receiver is turned off and on again.
1. Standby LED Dimmed LED indicates the power source
(AC Adapter or Battery) is on stand by. Brightly lit LED
indicates the power is ON.
2. 4 inch (diagonal) screen
3. 2.4 GHz Antenna
4. DC 12V input socket
Connect with an AC/DC adapter (12V, IA)
5. A/V Input jack Input of Audio, Video signal
6. A/V Output jack Output of Audio, Video signal
7. Power ON/OFF Key
8. Mute Key Mute audio
9. ^ Key: Volume up/Function Setting
vKey: Volume down/Function Setting
When using function setting mode after pressing function key
^ : to move cursor up
v : to move cursor down
10. CH Key: To select channel number 1-4 manually.
11. Auto Key: Auto channel switching.
12. Function Key: Adjusting/Setting up auto channel
switching, dwell time, brightness, contrast, color, etc.
Warranty
This warranty gives the original purchaser specific legal rights.
The original purchaser may also have other rights which vary
from state to state.
If products do not function because of any defect in material or
workmanship, they will be repaired free for a period of one year
on labor and parts from the date of original purchase. This
warranty does not cover modification, abuse, or neglect. This
warranty does not cover incidental or consequential damages
unless the state of owner's residence specifically prohibits
limitations on incidental or consequential damages.
How to Obtain Service Within Warranty
Please pack unit carefully and safely and send it prepaid by
insured parcel post to:
Saddlebrook BarnCams LLC
N76 W36096 Saddlebrook Lane
Oconomowoc, WI 53066 USA
Please include a note explaining how the unit is defective.
We will repair or replace and return to owner all units under this
limited warranty.
How to Obtain Service After Warranty Expiration
Follow the instructions for “Service Within Warranty” and
include a check for $20 to cover the costs of return postage and
handling. Include your e-mail address for faster and more
accurate communication. An estimate of the repair/replacement
cost will be sent for advance approval.
If you have any questions or need
additional help please e-mail:
or call: (920)474-7776
Saddlebrook BarnCams LLC
N76 W36096 Saddlebrook Lane
Oconomowoc, WI 53066
Andere Saddlebrook BarnCams Sicherheitskamera Handbücher
