SainSmart GENMITSU 3018-PROVer Bedienungsanleitung
V1.2 Jun 2020
USER MANUAL
Genmitsu CNC Router 3018-PROVer
01
Welcome
Disclaimer
Part 1 - Unboxing
Part 2 - Mechanical installation
Part 3 - Wiring
Part 4 - Software Setup
Part 5 - Using Offline Controller
Part 6 - Troubleshooting
02
03
04
08
22
39
39
40
..........................................................................................................................................
.......................................................................................................................................
...........................................................................................................................
.................................................................................................................
.................................................................................................................................
...................................................................................................
.................................................................................................
..............................................................................................................
Contents
02
Thank you for purchasing the Genmitsu 3018-PROVer CNC Router from SainSmart.
Included in your package will be a Micro SD card. On the Micro SD Card, you will find:
● Assembly instruction videos
● PDF version of this manual
● Windows USB Driver
● GrblControl/Candle software for Windows
● Sample files
● Offline Controller control files
These files can also be downloaded from SainSmart Online Resource Center
https://docs.sainsmart.com/3018-prover
Before attempting to assembly the 3018 PROVer, please watch the assembly video on
the Micro SD card. This will help you and avoid mistakes.
For technical support, please email us at [email protected].
Help and support is also available from our Facebook group.
(SainSmart Genmitsu CNC Users Group)
Welcome
Scan QR code
to join the group
03
Before operating your Desktop CNC Machine, please read the manual. Failure to do so may lead to personal injury, poor results,
or damage to the CNC Machine. Anyone who operates the Desktop CNC machine should know and understand the contents of
this manual.
SainSmart cannot control the conditions in which you assemble your Genmitsu CNC machine or verify if it was done properly.
We do not assume responsibility and expressly disclaim liability for loss, injuries, damage, or expense arising out of, or in any way
connected with the assembly, handling, storage, use, or disposal of the product.
The information in this manual is provided without any warranty, expressed or implied, regarding its correctness.
Please be careful when using your CNC machine. This machine is an electrical device with moving parts and
dangerous areas.
● Genmitsu CNC Machines are for Indoor Use Only.
● You must be 18 years or older to operate this machine, unless supervised by a knowledgeable adult familiar with the machine.
● Wear the proper Personal Protection Equipment (Safety Glasses etc.).
● Always place the CNC Machine on a stable surface.
● The SainSmart Genmitsu CNC Machine is supplied with Switchable Power Supply 230 VAC or 110VAC. Never use a different
power supply; it may cause malfunctions or damage to the machine.
● Ensure the Emergency stop button is easily accessible at all times.
● Never disassemble the Power Supply or Electrical Components. This will VOID the warranty.
● DO NOT TOUCH the machine spindle, or place any body part near the working area when the machine is operating. Serious
Injury may occur.
● DO NOT leave children unsupervised with the CNC Machine even when it’s not operating. Injury may occur.
● DO NOT leave the machine unattended while it's operating.
● Ensure your CNC Machine is in a well-ventilated area. Some Materials may discharge smoke or fumes during operation.
Disclaimer
04
X-Axis/Z-Axis Gantry Y-Axis Base Assembly
1
(2) Acrylic Baffle
5
10 11
2
Offline Controller
6 7 8
9
3 4
Spindle with ER11 tail ER11 1/8" Collet
Main Control Board USB A-to-B Cable
Power Supply Power Adapter Cable - US Power Adapter Cable - EU (4) Limit Switch
12
Please make sure all the following parts are included. If you are missing any part or have any questions, please email us at
Part 1 - Unboxing
05
Offline Controller Cable
13
Spindle Cable, 35cm
23
28 29
Emergency Stop
Button with Cable
24 25 26
27
Work Clamp Set Z-Probe Kit
(10) 20-degree V Bit Allen Wrench Set,
2mm, 2.5mm, 3mm, 4mm, 5mm (2) Wrench Screwdriver
30
14
15
16
17
18
19
Limit Switch Cable X LIM+, 15cm
Limit Switch Cable X LIM-, 53cm
Limit Switch Cable Y LIM+, 30cm
Limit Switch Cable Y LIM-, 60cm
Limit Switch Cable Z LIM+, 34cm
Limit Switch Cable Z LIM-, 40cm
20
21
22
Stepper Motor Cable, X-Axis, 17cm
Stepper Motor Cable, Y-Axis, 52cm
Stepper Motor Cable, Z-Axis, 28cm
06
Spacer Template Tool
31
39
(30) Cable Tie
32 (10) Cable Holder
33
36 Cable Protector
49
37 38
MicroSD Card MicroSD Card
Reader User Manual 40 (4) Rubber
Foot
(8) M5 10mm Bolt
(12) M5 14mm Bolt
(2) M6 16mm Bolt
41
42
43
(2) M3 20mm Screw
(16) M3 5mm Screw
(4) M3 8mm Screw
44
45
46
34
35
Sealing Strip, Y-Axis, 27cm
Sealing Strip, X-Axis, 34cm
47
48
(4) M3 20mm T-Slot Nut
(8) M5 20mm T-Slot Nut
(2) ABS
Spacer
V1.2 May 2020
USER MANUAL
Genmitsu CNC Router 3018-PROVer
07
Optional Accessories (Not Included)
Consider following optional upgrades or accessories to make your CNC experience better!
You can find them on www.sainsmart.com.
Save 10% with discount code PROVER10
5.5W Laser Module CNC Router Bits Essential Kit Resin Board for CNC
Engraving, 2-Pack
Acrylic Sheet for CNC,
180 x 100 x 5mm, 4-Pcs
Scan QR codes to learn more
08
43 Allen Wrench Set,
5mm
(2) M6 16mm Bolt
2.1 Preparing your base assembly
What you will need
Step 1: Flip the Y-Axis Base Assembly
upside down and remove the cable ties
from the bearing mount.
Step 2: Align the Aluminum Build Plate
center slot with the blue Y-Axis lead
screw mount as shown in the picture.
Step 3: Tighten (2) M6 16mm screws
to secure the lead screw mount.
28
Part 2 - Mechanical installation
Y-Axis Base Assembly
2
09
Y-Axis Base Assembly
2
Step 1: Locate the Limit switch mount indents on the inner side of the frame. One on each side as shown below.
Step 2: Install cable wire holders in the pre-drilled holes next to the limit switches, using the 3mm screws. Install two cable
holders on each side, facing inside the frame. Install two on the outside of the frame in the back (the stepper motor side).
45 (10) M3 5mm Screw
2.2 Installing limit switches & cable holders to Y-Axis
What you will need
(6) Cable Holder
33 (2) Limit Switch
12 Screwdriver
30
Andere Handbücher für GENMITSU 3018-PROVer
1
Inhaltsverzeichnis
Andere SainSmart Netzwerk-Router Handbücher
Beliebte Netzwerk-Router Handbücher anderer Marken
NETGEAR
NETGEAR FS526T - Switch Bedienungsanleitung
Korenix
Korenix JetNet 5710G Series Bedienungsanleitung
Automated Logic
Automated Logic ZN551 Betriebsanleitung
Cisco
Cisco ASR 1000 Series Bedienerhandbuch
EnGenius
EnGenius ESR-9710 Bedienungsanleitung
Cisco
Cisco 805 Series Bedienungs- und Sicherheitshinweise