Salus ST620RF Bedienungsanleitung

Instruction Manual

S-Series Digital Thermostat

Model No ST620RF

ST620RF Manual Version 005 CMYK:Layout 1 1/9/10 11:56 Page 1

ST620RF INSTRUCTION MANUAL2

ST620RF Manual Version 005 CMYK:Layout 1 1/9/10 11:56 Page 2

PRODUCT COMPLIANCE

This product complies with the essential requirements of the following EC Directives:

•Electro-Magnetic Compatibility Directive 2004/108/EC

•Low Voltage Directive 2006/95/EEC

•EC Marking Directive 93/68/EEC

SAFETY INFORMATION

These instructions are applicable to the Salus Controls model stated on the front cover of this manual

only, and must not be used with any other make or model.

These instructions are intended to apply in the United Kingdom only, and should be followed along

with any other statutory obligations.

This accessory must be fitted by a Competent person, and installation must comply with the guidance

provided in the current editions of BS7671 (IEE Wiring Regulations) and Part ‘P’ of the Building

Regulations. Failure to comply with the requirements of these publications could lead to prosecution.

Always isolate the AC Mains supply before opening or removing the receiver from the wall or wall box.

When fitting batteries don’t mix old and new batteries together. Do not use rechargable batteries.

Please leave these instructions with the end user where they should be kept in a safe place for future

reference.

3ST620RF INSTRUCTION MANUAL

ST620RF Manual Version 005 CMYK:Layout 1 1/9/10 11:56 Page 3

INTRODUCTION

A programmable thermostat is a device that combines the functions of both a room thermostat and heating

controller into a single unit. The programmable thermostat is used to switch the heating system by means of time

and temperature change. This unit is not like a standard programmer. It works by controlling the temperature

according to a series of programmed settings that take effect at different times of the day.

The ST620RF from Salus Controls is a stylish and accurate 5/2 or 7 day

programmable electronic thermostat with a large, easy to read Liquid Crystal

Display (LCD). This programmable thermostat has been specifically designed to

be used Volt Free. Unlike ordinary single unit design programmable thermostats,

this is a new type of unit that separates the operational functions into two units.

The Receiver is used for wiring connections and heat on/off control. The Control

Centre provides the user interface and temperature sensing / control. The two

units are linked together by a Radio Frequency (RF) signal.

The use of the revolutionary Touch Ring technology makes for simple usage, and

is coupled with a unique, smart design. The LCD display will show the current room

temperature and the ‘one touch’ operation makes the ST620RF easy to operate.

ST620RF INSTRUCTION MANUAL4

FEATURES

•Touch Ring Technology

•Large LCD with White Backlight

•Stylish Casing

•Volt Free Contacts

•Intelligent Communication Technology

•Battery Powered with Replacement Indicator

•Frost Protection

•Burner on Symbol

•Radio Controlled Clock (RCC)

•Manual Time / Date Setting Option

•Holiday Function

•Service Function

•Six Time / Temperature Settings / day

•Secure RF Transmission

(one million unique RF address codes)

ST620RF Manual Version 005 CMYK:Layout 1 1/9/10 11:56 Page 4

INSTALLATION

Please read the important safety information at the start of this manual before you begin to install the device.

The ideal position to locate the ST620RF programmable thermostat is about 1.5m above floor level. It should be

mounted in a location where the thermostat is accessible, reasonably lit and free from extremes of temperature and

draughts. Do not mount the thermostat on an outside wall, above a radiator or in a location where it may be

subjected to direct sunlight.

The ST620RF should be mounted in a location where it will not come into contact with moisture or condensation,

as this can affect the Touch Ring operation.

To ensure trouble free reception for both the Radio Controlled Clock (RCC) and the Radio Frequency (RF) signal,

always ensure that the programmable thermostat is mounted away from any possible sources of interference (such

as radios, TV sets, computers, etc.), and is not mounted on or in close proximity to large metal objects. Installing

the ST620RF in enclosed areas such as cellars and basements is not recommended.

5ST620RF INSTRUCTION MANUAL

RECEIVER BOILER

MAINS

FEED

Thermostat loop (Remove link)

Live Feed

LSL LNE

COM N/O L N

ST620RF Manual Version 005 CMYK:Layout 1 1/9/10 11:56 Page 5

CONNECTING THE ST620RF RECEIVER

NOTE: All electrical installation work should be carried out by a suitably qualified Electrician or other competent

person. If you are not sure how to install this digital thermostat consult either with a qualified electrician, heating

engineer or your boiler / heating system supplier for advice on how to continue.

The ST620RF Receiver should be mounted in a suitable location that is both accessible for the connection of mains

and control wiring, and allows good reception of the RF signal. The Receiver needs a 230V AC mains supply to

operate, and this should be fused appropriately (16A max.).

The Receiver should be mounted in a location where it will not come into contact with water, moisture or

condensation. There are few electrical connections required to the ST620RF, and these connections should be made

to the terminal block inside the Receiver. No Earth connection is required for the correct and safe operation of the

ST620RF, but a parking terminal is provided to connect an Earth wire if one is present.

These electrical connections are shown in the table below:

ST620RF INSTRUCTION MANUAL6

Terminal Function

COM Common Contact (volt free input)

NO Normally Open Contact (volt free output)

Earth Parking (No electrical connection)

L Incoming Mains - Live

N Incoming Mains - Neutral

ST620RF Manual Version 005 CMYK:Layout 1 1/9/10 11:56 Page 6

7ST620RF INSTRUCTION MANUAL

INSTALLING AND REPLACING BATTERIES

Installing or replacing the ST620RF Control Centre batteries is a

straightforward operation, but does require you to open the case of

the programmable thermostat.

To open the ST620RF case, undo the securing screw on the bottom of

the case (just to the right of the hole for the Reset Button):

After undoing the screw pull it forward until the screw stops

moving, then carefully separate the two halves of the case by gently

pulling in an upwards direction. Once the case has been separated,

the batteries should be visible:

Ensure that the batteries are inserted correctly, paying careful

attention to the polarity markings on the battery and next to the

battery holders. After inserting the batteries, refit the ST620RF case

and retighten the securing screw.

ST620RF Manual Version 005 CMYK:Layout 1 1/9/10 11:56 Page 7

PAIRING THE ST620RF RECEIVER AND CONTROL CENTRE

It is important to correctly pair both the Receiver and Control Centre to ensure that the RF address codes are matched

and that reliable communication is established between the units. Please follow the instructions below to ensure that the

units are configured correctly.

On the Receiver:

Press and hold the SYNC button to allow the Receiver to enter the learning mode. The Red SYNC LED will turn on to

indicate it is ready to receive a signal and pair with another unit.

While the signal is being received, the SYNC LED will turn on until the pairing has completed successfully; the SYNC LED

will then turn off and the Green Power LED will turn on again. The Control Centre will continue to transmit a pairing signal

for 10 minutes before returning to NORMAL mode.

On the Control Centre:

The Arrow key is not active when the ST620RF is in NORMAL mode. To access the Menu screens,

press the OK key twice. The first menu displayed is the PROGRAMME menu:

ST620RF INSTRUCTION MANUAL8

ST620RF Manual Version 005 CMYK:Layout 1 1/9/10 11:56 Page 8

Use the Touch Ring to scroll through the Menus, and press the OK key to select the menu you want to use:

You can scroll through the menus in either direction (forwards or backwards) depending on the direction you move

your finger around the Touch Ring. The menus are displayed in the order shown in the picture above.

Pressing the Arrow key will return the ST620RF to NORMAL mode. The thermostat will also return to NORMAL mode

after 10 seconds if no Key is pressed or if no movement is detected on the Touch Ring.

9ST620RF INSTRUCTION MANUAL

ST620RF Manual Version 005 CMYK:Layout 1 1/9/10 11:56 Page 9

After selecting the PAIR Menu, PAIR and the RF icon are displayed.

Press the OK key to start sending the RF address code to the Receiver.

The ST620RF Control Centre display will change to show a rundown timer:

The unit counts down for a period of 10 minutes, with the RF Signal indicator flashing while the signal is being

transmitted. The RF address code will be generated randomly and the Control Centre will transmit the signal every

second for the full 10 minutes until:

• The Arrow key is pressed to return to the previous display

• The OK key is pressed to return to NORMAL mode

• The 10 minute timer runs out

Note that the Receiver must be already in learning mode BEFORE attempting to access the PAIR menu on the Control

Centre. If the Red SYNC LED has not turned off after 10 minutes, repeat the whole pairing process.

Pressing the Reset button on the Control Centre and the Receiver will clear the RF address code and generate a new

default code which will be saved into the internal memory of the unit; there is no need to re-pair the Receiver and

Control Centre. This is a quick and easy way to directly link the units in many applications.

ST620RF INSTRUCTION MANUAL10

ST620RF Manual Version 005 CMYK:Layout 1 1/9/10 11:56 Page 10

Inhaltsverzeichnis

Andere Salus Thermostat Handbücher

Salus

Salus ST921WF Bedienungsanleitung

Salus

Salus CT100 Bedienungsanleitung

Salus

Salus BTRP230(50) Bedienungsanleitung

Salus

Salus ST325TX Bedienungsanleitung

Salus

Salus RT510BC Bedienungsanleitung

Salus

Salus SOLO ST920WF Bedienungsanleitung

Salus

Salus RT510BC+ Bedienungsanleitung

Salus

Salus RT 10 Bedienungsanleitung

Salus

Salus RT510 Bedienungsanleitung

Salus

Salus TH-3 Bedienungsanleitung

Salus

Salus ERT50 UP Bedienungsanleitung

Salus

Salus ST910WZ CA Bedienungsanleitung

Salus

Salus ST320 Bedienungsanleitung

Salus

Salus ERT30 Bedienungsanleitung

Salus

Salus BTRP230V Bedienungsanleitung

Salus

Salus HTR-RF(20) Bedienungsanleitung

Salus

Salus ST620WBC Bedienungsanleitung

Salus

Salus RT310SR Bedienungsanleitung

Salus

Salus Quantum SQ610 Bedienungsanleitung

Salus

Salus RT510BC+ Bedienungsanleitung

Salus

Salus QUANTUM SQ610RF Bedienungsanleitung

Salus

Salus iT500 Bedienungsanleitung

Salus

Salus VS20WRF Bedienungsanleitung

Salus

Salus ERT20RF Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Honeywell

Honeywell CM721 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

Honeywell

Honeywell RLV4305 Bedienungsanleitung

Honeywell

Honeywell Prestige 2.0 THX9421 Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung