Sam4s ELLIX50 Bedienungsanleitung
User Guide
ELLIX50
Receipt Printer
All specifications are subject to change without notice.
OPERATOR’S Manual 3
Warning - U.S.
This equipment has been tested and founded to comply with the limits for a Class
A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
In case, Operation of this equipment in a residential area is likely to cause harmful
interference to radio communications. the user will be required to correct the
interference at his own expense.
Notice - Canada
This Apparatus complies with class “A” limits for radio interference as specified in the
Canadian department of communications radio interference regulations.
Get appareil est conforme aux normes class “A” d’interference radio tel que specifier
par ministre canadien des communications dans les reglements d’interference radio.
Warning
This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
FCC compliance Information(for WLAN)
This device complies with part 15 of FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) This
device must accept any interference received, including interference that may cause
undesired operation.
Information to the user
NOTES :This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
[IMPORTANT NOTE]
FCC RF Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20centimeters between the radiator and your body. This
transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Caution
Some semiconductor devices are easily damaged by static electricity.You should turn
the printer “OFF”, before you connect or remove the cables on the rear side, in order
to guard the printer against the static electricity. If the printer is damaged by the static
electricity, you should turn the printer “OFF” and contact your dealer for assistance.
INTRODUCTION
The ELLIX50 Roll Printer is designed for use with electronic instruments such as
system ECR, POS, banking equipment, computer peripheral equipment, etc.
The main features of the printer are as follows:
1. High speed printing : 250mm/s, 59 lines per second(12X24 Font)
2. Low noise thermal printing.
3. Support a variety of interfaces : USB default / USB+RS-232(Serial) / USB+WLAN
USB+ETHERNET+RS-233(Serial)
4. Jam free (Implementation of automatic return of Cutter Jam)
5. Characters can be scaled up to 64 times compared to it’s original size.
4ELLIX50 Receipt Printer
OPERATOR’S Manual 5
6. The data buffer allows the unit to receive print data even during printing.
7. Bar code printing is possible by using a bar code command.
8. Different print densities can be selected by DIP switches.
9. Peripheral units drive circuit enables control of external devices such as cash
drawer.
10. 2-dimensional bar code(PDF-417) and
Two color printing.
Please be sure to read the instruction in this manual carefully before using ELLIX50.
NOTES : The Power outlet shall be near the equipment and it should be easily accessible.
LEGISLATION AND WEEE SYMBOL
2002/96/CE Waste Electrical and Electronic Equipment Directive on the treatment, collection,
recycling and disposal of electric and electronic devices and their components.
The crossed dustbin symbol on the device means that it should not be disposed of
with other household wastes at the end of its working life. Instead, the device should
be taken to the waste collection centres for activation of the treatment, collection,
recycling and disposal procedure.
To prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this
product, or their local government office, for details of where and how they can take
item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of
the purchase contract.
This product should not be mixed with other commercial wastes for disposal.
Contents
Chapter 1. Setting Up the Printer ·························· 7
1.1. Unpacking·····································································7
1.2. Connecting the Cables················································7
1.3. Connecting the host device········································8
1.4. Connecting the Drawer···············································8
1.5. Connecting the Power Supply ···································9
1.6. Installing options & Replacing the Paper Roll ·······10
1.6.1. Partition Installation············································ 10
1.6.2. Wall Mount Installation ······································ 11
1.6.3. Splash Cover Installation ···································12
1.6.4. Paper Roll Installation ········································12
1.7. Adjustments and Settings ········································13
1.7.1. Serial Interface(RS-232C) DIP Switch Set············ 14
1.7.2. WLAN Interface DIP Switch Set···························15
1.7.3. Serial+Ethernet Interface DIP Switch Set············ 15
1.8. Using the Printer ·······················································16
1.8.1. Control Panel (LED) ············································16
1.8.2. Feed Button ···················································16
1.8.3. Panel lights : LED ···············································16
CHAPTER 2. APPENDIX ····································· 17
2.1. Adjusting the Paper Near-End Sensor Location ···17
2.2. Printer Head Cleaning ··············································18
2.3. Error Status and Error Resolution ··························19
2.4. Specification ······························································20
2.4.1. General Printer specification······························20
2.4.2. Paper specification·············································20
OPERATOR’S Manual 7
CHAPTER 1
Your printer box should include these items. If any items are damaged or
missing, please contact your dealer for assistance.
1.1. Unpacking
You can connect up to three cables to the printer. They are all connected to
the connector panel on the back of the printer, which is shown as below:
USB
connector
Interface connectorDrawer Kick-out
connector
Power supply
connector
NOTES : Before connection any of the cables make sure the both the printer and
connecting device are turned off.
1.2. Connecting the Cables
1
CHAPTER Setting Up the
Printer
Roll paperPower-cordInterface cable(option)
ELLIX50
Operator’s
Manual(option)
AC AdapterWall Mount(option)
UserGuide
ELLIX50
Receipt Printer
Allspecifications are subject to change without notice.
8ELLIX50 Receipt Printer
You need the appropriate interface cable.
1. Plug the cable connector securely into the printer’s interface connector.
2. Tighten the screws on both sides of the cable connector.
3. Attach the other end of the cable to the host device.
1.3. Connecting the host device
WARNING : Use a drawer that matches the printer specification.
Using an improper drawer may damage the drawer as well as the printer.
CAUTION : Do not connect a telephone line to the drawer kick-out connector;
otherwise the printer and the telephone line may be damaged. Plug the drawer cable
into the drawer kick out connector on the back of the printer next to the power supply
connector.
1.4. Connecting the Drawer
To use the drawer, you can
connect the cable to the
connector.
OPERATOR’S Manual 9
CHAPTER 1
WARNING : Make sure that you use the power supply provided with the printer or
equivalent.
CAUTION : When connecting or disconnecting the power supply from the printer,
make sure that the power supply is not plugged into an electrical outlet. Otherwise
you may damage the power supply or the printer.
If the power supply’s rated voltage and your outlet’s voltage do not match, contact
your dealer for assistance. Do not plug in the power cord. Otherwise, you may
damage the power supply or the printer.
1. Make sure the printer is turned off.
2. Plug the DC cord connector into the power jack on the printer. If it is
necessary to connect the interface and the drawer, plug that connector
into the port on the printer. And clean up the cables.
NOTES :To remove the DC cable connector, make sure the power supply’s power cord
is unplugged and then grasp the connector at the arrow and pull it straight out.
1.5. Connecting the Power Supply
UP
➊
➌
➋
➍
10 ELLIX50 Receipt Printer
1.6.1. Partition Installation
You can install the partition for 58mm paper printing on printer.
1. Push the Open-Button and open the Cover-Open.
2. Remove the partition as indicated in picture 4 below.
3. Insert the partition into the slot for 58mm wide roll as indicated in 5 & 6 below.
➌
➎
open
➋➊
➍
➏
1.6. Installing options & Replacing the Paper Roll
Inhaltsverzeichnis
Andere Sam4s Drucker Handbücher
Sam4s
Sam4s GIANT-100 Bedienungsanleitung
Sam4s
Sam4s ELLIX 35III Bedienungsanleitung
Sam4s
Sam4s ELLIX 20 Bedienungsanleitung
Sam4s
Sam4s giant 100 series Bedienungsanleitung
Sam4s
Sam4s Gcube-100 Bedienungsanleitung
Sam4s
Sam4s ELLIX 20 Bedienungsanleitung
Sam4s
Sam4s ELLIX35III Bedienungsanleitung
Sam4s
Sam4s ellix 30 Bedienungsanleitung
