Samsung SHP-3701F Bedienungsanleitung
In-ceiling Housing
Installation Manual SHP-3701F
2_ SHP-3701F
TABLE OF CONTENTS
Overview ···························································································································· 3
What’s Included ················································································································· 3
Installation Instructions······································································································4
Installation (SCP-3430 Series) ··························································································· 4
Installation (SCP-3370/SNP-5200 SERIES) ······································································ 9
Installation (SCP-3371/SNP-5300 SERIES) ···································································13
Product Specifications····································································································18
SHP-3701F _3
ENG
OVERVIEW
This In-CEILING HOUSING is a mounting ADAPTOR that is designed to mount the smart
dome camera in built-in style on a double-layer ceiling.
WHAT’S INCLUDED
HOUSING SAFETY BRACKET (
1EA)
SAFETY WIRE (1SET)
TEMPLATE (1EA)
SCREW (7EA)
LOWER BRACKET
(SCP-3430 Series/
SNP-5300 Series)
(1EA)
In-ceiling Housing
Installation Manual SHP-3701F
INSTALLATION MANUAL
Fixing Bracket (1EA)
4_ SHP-3701F
INSTALLATION INSTRUCTIONS
Select an installation position or place that can endure more than 4 times of the total
weight of the installation structure.
At least 250mm or more of spare height is required above the CEILING BOARD.
CEILING BOARD’s thickness should be less than 40mm.
Be sure to secure the SAFETY WIRE to avoid a product fall.
If you want to attach the camera to the ADAPTOR, use the only provided SCREWS.
INSTALLATION (SCP-3430 SERIES)
Place the TEMPLATE on the CEILING BOARD and drill a guided hole.
❶ Remove the round filling (“C”) from the TEMPLATE.
➋ Place TEMPLATE A onto the CEILING BOARD to which you will attach the ceiling
mount ADAPTOR and drill a hole of Ø219mm in diameter.
See the figure below for the hole shape.
1.
2.
3.
4.
5.
1.
Ø219mm
형판
천장 보드
Ø219mm
250mm 이상일 것
천장보드 40mm 이하일 것
More than 250mm
CEILING BOARD Less than 40mm
TEMPLATE
CEILING BOARD
SHP-3701F _5
ENG
See the figure below to fix the lower BRACKET with the provided SCREWs.
Insert the FRAME SET included in the smart dome camera package into the HOUSING
and fix it using 3 provided SCREWs.
2.
3.
The lower BRACKET is specific to “SCP-3430 Series/SNP-5300 Series”.
하우징
하우징
프레임세트
스크류 스크류
FRAME SET
SCREW SCREW
HOUSING
HOUSING
6_ SHP-3701F
Fix the ANCHOR BOLT onto the concrete CEILING, and secure the SAFETY WIRE to the
ANCHOR BOLT as below:
❶ Tighten the nut (“N1”) on the ANCHOR BOLT.
➋ Insert the provided SAFETY BRACKET into the ANCHOR BOLT.
➌ Tighten two nuts (“N2”,”N3”) onto the ANCHOR BOLT.
➍ Hook and fix one end of the SAFETY WIRE onto the SAFETY BRACKET.
➎ Hook and fix the other end of SAFETY WIRE onto the HOUSING as shown below.
Press the SNAP-FIT on the ADAPTOR to open it, and insert camera cables and external
connection cables into the HOUSING through the side hole (see figure below).
Refer to the installation manual of the camera that you want to install, and prepare necessary
cables for camera connection.
4.
5.
M
앙카볼트
천장
너트(N1)
안전브라켓
앙카볼트
너트(N2,N3)
안전와이어
천장
하우징
INSTALLATION (SCP-3430 SERIES)
The ANCHOR BOLTs and nuts are optional and not included in the product package.
ANCHOR BOLT
Nut (N1)
Safety BRACKET
Nut (N2,N3)
SAFETY WIRE
ANCHOR BOLT
HOUSING
CEILING
CEILING
천장
홀하우징
하우징
어댑터
스냅핏 외부케이블
CEILING
Hole HOUSING
Adaptor
Snap-fit
HOUSING
External Cable
SHP-3701F _7
ENG
Push the HOUSING inside the CEILING through the CEILING hole, and tighten the
SCREWs (x2) clockwise to fix the HOUSING on the CEILING.
(The BRACKET will be positioned from <A> to <B> as shown.)
Ensure that the HOUSING is firmly secured to the CEILING BOARD.
Connect external cables to the CONNECTOR (ALARM-IN, POWER, RS-485 and ALARM
OUT) that is provided with the camera to be installed, and fit the CONNECTOR into the
ADAPTOR.
Push in the cables inside the FRAME, and close the ADAPTOR.
Make sure that you wrap the BNC JACK with the insulation tube and use the insulation tape to
seal up the end of the insulation tube lest that it should protrude.
For more information about the cable connection, refer to the installation manual of the camera.
6.
M
7.
M
브라켓
브라켓
<A상태> <B상태>
브라켓
하우징
브라켓
스크류
시계방향으로 회전
BRACKET
SCREW
Turn clockwise
HOUSING
BRACKET
BRACKET
BRACKET
<A> <B>
ALARM IN ALARM OUT
RS-485
전원
절연튜브
BNC잭
어댑터 프레임
하우징
천장
Power
Adaptor
BNC JACK Insulation Tube
Frame
HOUSING
CEILING
8_ SHP-3701F
Hook the SAFETY WIRE to the FRAME’s SAFETY HOOK.
Align the camera with the 22-Pin CONNECTOR of the ADAPTOR, and push the HOOK on
either end of the CAMERA in the RACK direction of the FRAME-SET to secure the two.
When the installation is completed, remove both PROTECTIVE TAPE and PRETOECTIVE COVER
from the lens.
Attach the COVER to the HOUSING. Fit the corner groove of the cover into one of 4
grooves on the HOUSING before fixing it.
8.
M
9.
INSTALLATION (SCP-3430 SERIES)
하우징
프레임
안전걸이
랙
안전와이어
카메라
어댑터
하우징
보호커버
보호테이프
천장
HOUSING
Frame
Safety
Hook
Rack
SAFETY
WIRE
Camera
Adaptor
PROTECTIVE TAPE PROTECTIVE COVER
CEILING
HOUSING
홈
하우징
홈
커버
홈
홈
Groove
Groove
Groove
HOUSING
Groove
Cover
SHP-3701F _9
ENG
INSTALLATION (SCP-3370/SNP-5200 SERIES)
Place the TEMPLATE on the CEILING BOARD and drill a guided hole.
❶ Remove the round filling (“C”) from the TEMPLATE.
➋ Place the TEMPLATE A onto the CEILING BOARD to which you will attach the
CEILING mount ADAPTOR and drill a Ø219mm hole.
See the figure below for the hole shape.
See the figure below to fix the INSTALL BASE that is provided as a camera accessory.
1.
2.
Ø219mm
형판
천장 보드
Ø219mm
Check the
arrow head
TEMPLATE
CEILING BOARD
10_ SHP-3701F
Fix the ANCHOR BOLT onto the concrete CEILING, and secure the SAFETY WIRE to the
ANCHOR BOLT as below:
❶ Tighten the NUT (“N1”) on the ANCHOR BOLT.
➋ Insert the provided SAFETY BRACKET into the ANCHOR BOLT.
➌ Tighten two NUTs (“N2”,”N3”) onto the ANCHOR BOLT.
➍ Hook and fix one end of the SAFETY WIRE onto the SAFETY BRACKET.
➎ Hook and fix the other end of SAFETY WIRE onto the HOUSING as shown below:
Press the SNAP-FIT on the ADAPTOR to open it, and insert camera cables and external
connection cables into the HOUSING through the side hole (see figure below).
Refer to the installation manual of the camera that you want to install, and prepare necessary
cables for camera connection.
3.
4.
M
천장
홀하우징
INSTALLATION (SCP-3370/SNP-5200 SERIES)
앙카볼트
천장
너트(N1)
안전브라켓
앙카볼트
너트(N2,N3)
안전와이어
천장
하우징
The ANCHOR BOLTs and nuts are optional and not included in the product package.
ANCHOR BOLT
CEILING
Nut (N1)
Safety BRACKET
Nut (N2,N3)
SAFETY WIRE
ANCHOR BOLT
HOUSING
CEILING
CEILING
HOLE HOUSING
Inhaltsverzeichnis
Andere Samsung Kamerazubehör Handbücher
Samsung
Samsung SCU-9080 Bedienungsanleitung
Samsung
Samsung SPH-20W/P Bedienungsanleitung
Samsung
Samsung STH-330POV Bedienungsanleitung
Samsung
Samsung STB-30PF Bedienungsanleitung
Samsung
Samsung SHD-3000F Bedienungsanleitung
Samsung
Samsung SNP-3750 Bedienungsanleitung
Samsung
Samsung SCX-300KM Bedienungsanleitung
Samsung
Samsung SCC-101 Bedienungsanleitung
Samsung
Samsung SPD-3750T Bedienungsanleitung
Samsung
Samsung SHG-220 Bedienungsanleitung
Samsung
Samsung SCU-2370 Bedienungsanleitung
Samsung
Samsung SHB-4300H1 Bedienungsanleitung
Samsung
Samsung SCU-VAC Bedienungsanleitung
Samsung
Samsung SHG-222 Bedienungsanleitung
Samsung
Samsung SCU-2370 Bedienungsanleitung
Samsung
Samsung SHP-3700H Bedienungsanleitung
Samsung
Samsung SCX-RD100 Bedienungsanleitung
Samsung
Samsung SPD-3700T Bedienungsanleitung
Samsung
Samsung SCX-300LM Bedienungsanleitung
Samsung
Samsung SCU-2370 Bedienungsanleitung
