Samsung 050JXYDEH Handbuch

2016 b fast connect 1

with

Scan this code to go directly to our YouTube channel

Air Source Heat Pump

Installation and Maintenance Manual

Model Numbers:

MIM-E03 A and B N

AE 050-090-120-140-160JXYDEH

2016 b fast connect 2

The Outdoor Unit (boiler)

Position the outdoor unit so that the air flows into an open area, where there are no

plants and animals

Install the outdoor unit on a flat, stable surface, the unit needs to be securely

mounted at least 100mm off the ground on rubber feet. The unit must be bolted down

for security using 10mm bolts and Zebedee bolts.

The unit must have adequate drainage away from the unit; it can produce up to 6 L /

hour. If you are installing the unit at height you can install a drain pan under the unit

but its best to let the unit drain into the ground.

Dimensions:

Size 16 - 1420mm (h) 940mm (w) 330mm (d) 103kg

Size 9 - 998mm (h) 940mm (w) 330mm (d) 75kg

Size 5 - 798mm (h) 880mm (w) 310mm (d) 59kg

The space around the unit is very important, allow:

300mm to the left hand side (facing the front of the unit), 600mm to the right of the

unit, 300mm to the rear of the unit and 1500mm to the front of the unit.

2016 b fast connect 3

What comes with the unit and what you will need:

Below is a list of the components which comes with fast connect,

Flexible hoses the water connections to the back of the

unit are 1 inch BSP male. We recommend connecting the

water pipework with flexible hoses for ease of maintenance

and to avoid any vibration from the unit going into the

house. All external pipework has to be insulated to meet

MCS standards.

Mounting feet, the outdoor units need to be mounted

100mm above the ground, we recommend using rubber feet with

unistrut channel. These come with mounting bolts included.

An expansion vessel, pressure gauge, pressure relief valve

and filling loop

In pressurised heating systems most heating engineers use a Robokit

which combines all these components into one box. The expansion

vessel is sized exactly the same way as when using a boiler. If you

want to run the system open vented you don’t need these components,

the Samsung units are happy to run at anywhere from 0 – 3Bar

pressure

Diverter valves

If you require multiple heating zones you need to supply a 2 port diverter

valves per zone.

Glycol / anti-freeze

In Monobloc heat pumps the water goes outside the building. The unit can protect

itself from freezing up, but if the power goes off there is a risk that the unit will freeze

causing damage. To prevent this, we recommend putting propylene glycol mixture in

the system. It is important that the glycol concentration is

adequate to protect the unit, if the unit freezes up there

will be no warranty. Manufacturer dependant, a mix of

25% is normal for UK conditions.

Adding too much glycol is not a good idea as it increases the water pump power and

slightly reduces the capacity of your system.

The Cylinder:

If you want to heat water with a heat pump you need a dedicated heat pump cylinder.

The cylinder needs to be installed less than 15m from the control box to allow for the

temperature sensor cable.

Cylinders can only be used IF the coil area is more than 2.5m^2. Smaller coils are

not acceptable and cannot be used. Please do not attempt to utilize a standard

central heating, non-heat pump optimized cylinder. Cylinders can be pressurised or

open vented.

2016 b fast connect 4

Fast Connection kit page 1 of 4

The fast connection kit comes with all the accessories you need except a robokit and

Cylinder. The idea is the fast connect kit goes on the wall inside and is pre wired, and

commissioned. The plumber connects the cylinder, the heat pump and the heating

circuit.

2016 b fast connect 5

Fast Connect Page 2 of 4

Operation:

Hot water is controlled using the Samsung cylinder sensor and controller supplied.

This controller has inbuilt time clock control and includes both a daily and weekly

legionella sterilisation function.

The system can be either open vented or pressurised.

The cylinder must have a coil at least 2.5m^2

Cylinder size normally allows 55l of water per person per day.

We would recommend sizing the heat pump to recover the cylinder in 1 hour.

It is possible to connect this system to solar PV powered immersion heaters (I boost,

Immersun etc.)

Heating is controlled using a wall mounted thermostat / time clock (field supplied).

There are no limits to the number of heating zones which can be connected to this

system. This system shows 2 heating zones. (Pump 2 and Pump 3)

Each zone has its own thermostat / timer which drives a dedicated zone valve. The

zone valve will control the pump and send a run signal to the heat pump.

The system will run in a fully adjustable weather compensated mode adjusting the

water temperature to suit the ambient conditions.

We recommend a buffer; low loss header or heat exchanger is used to simplify the

installation.

2016 b fast connect 6

Wiring Fast Connect with one zone heating page 3 of 4

The sparky connects the tank thermostat sensor 15m long (can’t be extended).

The immersion heater to the cylinder, the thermostat or run signal input

The 2 core F1F2 cable to the outdoor unit (its 10m long) and a power supply 16

Amps

2016 b fast connect 7

Wiring Fast Connect with multi heating zones page 3 of 4

The sparky connects the tank thermostat sensor 15m long (can’t be extended).

The immersion heater to the cylinder, the thermostat or run signal input

The 2 core F1F2 cable to the outdoor unit (its 10m long) and a power supply 16

Amps

2016 b fast connect 8

Combi hybrid with fast connection kit:

The fast connect board goes outside, it’s in a waterproof enclosure, 600 high x 800

wide x 300mm deep. The fast connection kit has energy meters installed so the

installer needs no other parts. Just T into the heating circuit and modify the wiring as

above.

2016 b fast connect 9

Combi hybrid with fast connection kit wiring:

Disconnect the stat from the boiler and wire it to the fast connect.

Run a cable from fast connect to the boiler.

Connect a single power supply to the fast connect board.

Run a supply from fast connect to the heat pump outdoor unit

Connect the pre wired comms cable to the outdoor unit.

2016 b fast connect 10

Start-up Procedure:

Filling and flushing, when installing any Heat pump we insist on a thorough

system flush prior to connection in line with the Building Regulations for England and

Wales, Part L, 2006.

Using the power flusher fill the system with water and 25% Propylene Glycol, there is

no pressure sensor in the unit so we can operate from open vented to 3 bar

maximum.

Setting up the cylinder immersion heater

The immersion heater has its own stat; this MUST be set to

70C. This is to avoid the immersion heater cutting out before

the legionella function is complete

Powering Up

Makes sure all your room thermostats are off and all underfloor run signals are

off.

Apply power to indoor control box first then the outdoor unit. Turn on all the breakers

in the fast connect.

The remote controller will be dead for about a minute, after that it will come to life.

You will see 00 or 01 on the remote controller screen for 90 seconds. If 01 continues

to show the outdoor unit is not powered up.

Setting the Clock and Backlight

1. Press User Set once 1 shows on the screen.

2. Press up until 2 shows,

3. Press right twice, Year will show, use up to change

year Press Set, 22 appears,

4. Press right Month will be flashing, adjust Month with

up,

5. Press right, day will be flashing, adjust day with up.

6. Press Set. 22 shows, press up once, 23 shows,

7. Press right, day and time are shown, day will be flashing, use up to adjust day,

8. Press right, AM or PM will be flashing, use up to adjust AM, PM or both (24-

hour clock)

9. Press right, hour will flash, press up to adjust hours

10. Press right, minutes will flash, use up to adjust minutes.

11. Press Set.

12. 23 shows, Press left 2 flashes, press up twice 4 flashes,

13. Press right, 4 0511 shows, 05 flashes.

14. Press up until 30 flashes,

15. Press Set,

16. Press ESC to finish and return to normal screen.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Samsung Wärmepumpe Handbücher

Samsung

Samsung AE RXYDEG Series Bedienungsanleitung

Samsung

Samsung MIM-E03EN Bedienungsanleitung

Samsung

Samsung AM CNBD Series Bedienungsanleitung

Samsung

Samsung RC090MHXEA Handbuch

Samsung

Samsung MIM-E03*N Bedienungsanleitung

Samsung

Samsung AE CXYD Series Bedienungsanleitung

Samsung

Samsung RD060PHXEA Bedienungsanleitung

Samsung

Samsung DV8 T 2 Series Bedienungsanleitung

Samsung

Samsung AEN160YDEHA Bedienungsanleitung

Samsung

Samsung AM BXVGFH/AA Series Gebrauchsanweisung

Samsung

Samsung AEX060EDEHA Bedienungsanleitung

Samsung

Samsung AE***JXYDGH Series Bedienungsanleitung

Samsung

Samsung AE050RXYDEG Bedienungsanleitung

Samsung

Samsung ERV Plus AM050FNKDEH Leitfaden

Samsung

Samsung CNH HDB Series Gebrauchsanweisung

Samsung

Samsung AM050FNKDEH Leitfaden

Samsung

Samsung AG TN1DKH Series Gebrauchsanweisung

Samsung

Samsung Max Heat DVM S2 Gebrauchsanweisung

Samsung

Samsung HHSM-G500005-1 Bedienungsanleitung

Samsung

Samsung CNH 4DB Series Gebrauchsanweisung

Samsung

Samsung AE RXEDGG Series Bedienungsanleitung

Samsung

Samsung AE090JXEDEH Bedienungsanleitung

Samsung

Samsung RC***MHXGA Bedienungsanleitung

Samsung

Samsung HHSM-G500005-1 Bedienungsanleitung

Beliebte Wärmepumpe Handbücher anderer Marken

MICROWELL

MICROWELL HP 1000 GREEN Bedienungsanleitung

Sanyo

Sanyo SAP120FCH Bedienungsanleitung

Daikin

Daikin EHYHBH05AA Bedienungsanleitung

Panasonic

Panasonic WH-SDF03E3E5 Leitfaden

Bryant

Bryant 544B Bedienungsanleitung

Airxcel

Airxcel 45000 Series Handbuch

Mitsubishi Electric

Mitsubishi Electric PUZ-SWM60VAA Bedienungsanleitung

Dimplex

Dimplex LI 16I-TUR Benutzerhandbuch

Carrier

Carrier WSHP Open v3 Kurzanleitung zur Einrichtung

TGM

TGM CTV14CN018A Bedienungsanleitung

Carrier

Carrier 38MGQ Series Bedienungsanleitung

Kokido

Kokido K2O K880BX/EU Fehlerbehebungshandbuch

Viessmann

Viessmann VITOCAL 300-G PRO Type BW 2150 Kurzanleitung

Carrier

Carrier 48EZN Bedienungsanleitung

Viessmann

Viessmann KWT Vitocal 350-G Pro Series Betriebsanleitung

Ariston

Ariston NIMBUS Bedienungsanleitung

Weishaupt

Weishaupt WWP L 7 Benutzerhandbuch

GE Zoneline AZ85H09EAC Bedienungsanleitung