Samsung SCC-B9373 Bedienungsanleitung

SCC-B9373

imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service, please register

your product at

www.samsung.com/global/register

operating instructions

DAY&NIGHT IR LED CAMERA

ENG FRA GER SPA ITA

01-SCC_B9373_EU-ENG.indd 1 2008-04-17 오후 1:44:30

safety precautions

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS

INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

This symbol indicates that dangerous voltage consisting a risk of electric shock is present

within this unit.

This symbol indicates that there are important operating and maintenance instructions in

the literature accompanying this unit.

WARNING

To reduce the risk of ﬁre or electric shock, do not expose this appliance to rain or moisture.

WARNING

1. Be sure to use only the standard adapter that is speciﬁed in the speciﬁcation sheet.

Using any other adapter could cause ﬁre, electrical shock, or damage to the product.

2. Incorrectly connecting the power supply or replacing battery may cause explosion,

ﬁre, electric shock, or damage to the product.

3. Do not connect multiple cameras to a single adapter. Exceeding the capacity may

cause abnormal heat generation or ﬁre.

4. Securely plug the power cord into the power receptacle. Insecure connection may

cause ﬁre.

5. When installing the camera, fasten it securely and ﬁrmly. A falling camera may cause

personal injury.

6. Do not place conductive objects (e.g. screwdrivers, coins, metal things, etc.) or

containers ﬁlled with water on top of the camera.

Doing so may cause personal injury due to ﬁre, electric shock, or falling objects.

7. Do not install the unit in humid, dusty, or sooty locations.

Doing so may cause ﬁre or electric shock.

8. If any unusual smells or smoke come from the unit, stop using the product.

In such case, immediately disconnect the power source and contact the service

centre. Continued use in such a condition may cause ﬁre or electric shock.

9. If this product fails to operate normally, contact the nearest service centre.

Never disassemble or modify this product in any way. (SAMSUNG is not liable for

problems caused by unauthorized modiﬁcations or attempted repair.)

10. When cleaning, do not spray water directly onto parts of the product.

Doing so may cause ﬁre or electric shock.

•

01-SCC_B9373_EU-ENG.indd 2 2008-04-17 오후 1:44:30

CAUTION

1. Do not drop objects on the product or apply strong shock to it.

Keep away from a location subject to excessive vibration or magnetic interference.

2. Do not install in a location subject to high temperature (over 122°F), low temperature

(below 14°F), or high humidity. Doing so may cause ﬁre or electric shock.

3. If you want to relocate the already installed product, be sure to turn off the power

and then move or reinstall it.

4. Remove the power plug from the outlet when then there is a lightning.

Neglecting to do so may cause ﬁre or damage to the product.

5. Keep out of direct sunlight and heat radiation sources. It may cause ﬁre.

6. Install it in a place with good ventilation.

7. Avoid aiming the camera directly towards extremely bright objects such as sun,

as this may damage the CCD image sensor.

8. Apparatus shall not be exposed to dripping or splashing and no objects ﬁlled with

liquids, such as vases, shall be placed on the apparatus.

9. The mains plug is used as a disconnect device and shall stay readily operable at any

time.

01-SCC_B9373_EU-ENG.indd 3 2008-04-17 오후 1:44:30

important safety instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings.

Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers,

or other apparatus (including ampliﬁers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug.

A polarized plug has two blades with one wider than the other.

A grounding type plug has two blades and a third grounding prong.

The wide blade or the third prong is provided for your safety.

If the provided plug does not ﬁt into your outlet, consult an electrician for replacement

of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories speciﬁed by the manufacturer.

12. Use only with cart, stand, tripod, bracket, or table speciﬁed by the manufacturer,

or sold with the apparatus.

13. Unplug this apparatus. When a cart is used, use caution when moving the cart/

apparatus combination to avoid injury from tip-over.

14. Refer all servicing to qualiﬁed service personnel.

Servicing is required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has been exposed to rain or moisture,

does not operate normally, or been dropped.

01-SCC_B9373_EU-ENG.indd 4 2008-04-17 오후 1:44:30

_01

contents

FEATURES

02 Features

NAME OF EACH PART

03 Name of each part

INSTALLATION

04 Camera Installation

TROUBLESHOOTING

05 Troubleshooting

SPECIFICATIONS

06 Speciﬁcations

DIMENSION

07 Dimension

contents

THINGS TO KEEP IN MIND

DURING INSTALLATION

AND USE

02 Things to keep in mind during installation and

use

01-SCC_B9373_EU-ENG.indd 1 2008-04-17 오후 1:44:30

02_

features

1/3” Sony super HAD CCD

Resolution: 540TVL (Color), 570TVL (B/W)

Minimum Scene Illumination 0 Lux (with LED On)

IR range Distance up to 70m

Color & B/W Auto switchable by Photocell and Sensitivity

Built-in 6~50mm / F1.6 Day & Night Vary-focal DC Auto Iris Lens

Externally Adjustable Focal Length & Focus with Lever

Externally Adjustable DC Iris Level

CDS Photocell Auto Switching IR- LED Control 42 LEDs

Cable Managed Bracket

Service Monitor Output

Waterproof Outdoor Installation (IP-66)

AC24V / DC12V

things to keep in mind during

installation and use

Do not disassemble the camera on your own.

Always be careful when handling the camera. Do not strike the camera by your

ﬁsts or shake it. Please be careful not to be careless when storing and operat-

ing it.

Do not place or operate the camera in any wet environment such as rain or

wet surfaces.

Do not clean the camera with rough sandpaper. Please always use a dry cloth

when cleaning it.

Put the camera in a cool area free from direct sunlight. Otherwise, the camera

may be damaged.

•

features

01-SCC_B9373_EU-ENG.indd 2 2008-04-17 오후 1:44:30

_03

ENG

name of each part

PAN TILT ADJUSTMENT

ZOOM LEVER

FOCUS LEVER

RING GUIDE BOLT

DC LEVEL VOLUME SCREW CAP

SERVICE VIDEO PORT

BRACKET

01-SCC_B9373_EU-ENG.indd 3 2008-04-17 오후 1:44:31

04_

installation

CAMERA INSTALLATION

Zoom and Focus Lever

- Loosen the Levers and adjust Zoom/Focus

After controlling, tighten each lever.

1. Zoom Lever

- To widen the viewing angle, turn the “Zoom Lever” to “W”(Wide)

- To obtain a closer view, turn this Lever to “T” (Tele).

2. Focus Lever

- To adjust the Focus between “N” (Near) or “ ” (Far) until the sharpest focus is achieved.

3. Ring Guide Bolt

• Be carefull not to lose these small bolts (3pcs) which should not be touched in normal

use.

4. DC Level Volume Screw Cap

• Remove this screw Cap carefully. Retain it in a safe place,

as it must be replaced to protect from water entering the camera body.

• The DC level volume for the adjustment in the screw hole.

- For a bright screen, turn the DC Level Volume slowly towards “H” (counter-clockwise) with the

driver provided.

- For a dark screen, turn it towards “L” (clockwise).

• Then tighten the screw Cap to protect water entering

5. Service Video Port Description

•

installation

250mm

01-SCC_B9373_EU-ENG.indd 4 2008-04-17 오후 1:44:31

_05

ENG

6. Bracket

Loosen the Pan/Tilt bolts of the bracket to adjust the camera direction.

In reference to page 3.

7. Connecting to Monitor and Power

- Set the impedance switch to the 75Ωstandard position unless a video equipment is connected

to the monitor video out.

- Adaptor: AC24V / 1.5A or DC12V / 1.5A (AC24V / DC12V Model)

• Be sure to connect power after all the installation is done.

• Do not use power sources other than that speciﬁed.

troubleshooting

If you have trouble operating the camera, check the following guides for the

possible problem.

Nothing appears on the screen.

- Check the power connection and video signal line connection.

- Check the brightness level of DC Auto Iris volume of the camera.

The video image is not clear.

- Check if the camera glass has dust on the surface.

Clean the camera glass with a clean cloth or brush.

- Make sure that the screen is not exposed directly to a bright light.

Adjust the position of the camera if necessary.

- Check if protective ﬁlm of camera glass is removed.

The screen is dark

- Adjust the brightness feature of the monitor.

- Check the brightness level of DC Auto Iris volume of the camera.

The screen does not properly display when IR LEDs work.

- Check if the camera glass has dust.

- Clean the camera glass with a clean cloth or brush.

If you cannot solve the problem with above guidelines, please contact an

authorized technician.

•

troubleshooting

01-SCC_B9373_EU-ENG.indd 5 2008-04-17 오후 1:44:32

06_

specifications

ITEM NTSC PAL

Image Sensor 1/3" Interline transfer type color CCD (SONY)

Effective Pixels 768H × 494V (380K pixels) 752H × 582V (440K pixels)

Scanning System 525 Lines 2:1 Interlace 625 Lines 2:1 Interlace

Scanning Frequency 15.734KHz (H), 59.94Hz (V) 15.625KHz (H), 50Hz (V)

Resolution 540TVL (Color), 570TVL (B/W)

Shutter Speed 1/60 sec. 1/50 sec.

S/N Ratio More than 48dB (AGC Off)

Sync. System Internal

Min. Illumination 0 Lux with IR-LED (42 pcs)

Video Output VBS 1.0 Vp-p (75 ohm Load)

Lens 6~50mm Day&Night Vary-Focal DC Auto Iris Lens (F1.6)

Power Supply(*) AC24V / DC12V ± 10%

Power Consumption 2.5W (LED Off)/ 14.4W (LED On)

Operating Temp. 14˚F~122˚F (-10˚C~50˚C)

Operational Humidity Max. 90% RH

Dimensions 98mm (Ø) x 162.4mm (L)

(*) Must use regulated & specified power supply.

speciﬁcations

01-SCC_B9373_EU-ENG.indd 6 2008-04-17 오후 1:44:32

Andere Handbücher für SCC-B9373

Inhaltsverzeichnis

Sprachen:

Andere Samsung IP-Kamera Handbücher

Samsung

Samsung SDC-9443BC Bedienungsanleitung

Samsung

Samsung SMARTCAM SNH-1011N Bedienungsanleitung

Samsung

Samsung SmartCam+ Bedienungsanleitung

Samsung

Samsung SCC-B9373 Bedienungsanleitung

Samsung

Samsung SCO-6083R Installationsanleitung

Samsung

Samsung SCP-2370 Bedienungsanleitung

Samsung

Samsung SCC-931T Bedienungsanleitung

Samsung

Samsung SCO-3080R Series Bedienungsanleitung

Samsung

Samsung SDC-435U Bedienungsanleitung

Samsung

Samsung SCO-1020R Bedienungsanleitung

Samsung

Samsung SNP-5430 Bedienungsanleitung

Samsung

Samsung SDC-9443BC Bedienungsanleitung

Samsung

Samsung SCO-3080R Series Bedienungsanleitung

Samsung

Samsung SCD-2021R Bedienungsanleitung

Samsung

Samsung GV-CLRIRH - GV-CLRIRH Day/Night Bullet IR... Montageanleitung

Samsung

Samsung SCC-B9373 Bedienungsanleitung

Samsung

Samsung SIR-4160 Bedienungsanleitung

Samsung

Samsung Beyond SCB-5003 Bedienungsanleitung

Samsung

Samsung SMARTCAM SNH-V6414BN Bedienungsanleitung

Samsung

Samsung SCD-2021R Bedienungsanleitung

Samsung

Samsung SCB-2005 Bedienungsanleitung

Samsung

Samsung SCD-2020R Series Bedienungsanleitung

Samsung

Samsung SNB-7000 Bedienungsanleitung

Samsung

Samsung SDC-9441BC Bedienungsanleitung

Beliebte IP-Kamera Handbücher anderer Marken

FLIR

FLIR Exx series Bedienungsanleitung

Avigilon

Avigilon H4A-BO1-IR Bedienungsanleitung

Digital Watchdog

Digital Watchdog DWCA-C128-64 Bedienungsanleitung

ShareTech

ShareTech AV1 Bedienungsanleitung

Ezviz

Ezviz C6C Bedienungsanleitung

Melchioni

Melchioni UCAM 2015 Bedienungsanleitung

Geutebruck

Geutebruck G-Cam/ESD-4630 Bedienungsanleitung

Arecont Vision

Arecont Vision MegaBall AV3146DN-3310-D-LG Bedienungsanleitung

Mitel

Mitel 6800i Series Service-Handbuch

Vitek

Vitek VTC-IR403-212NP Bedienungsanleitung

THOMSON

THOMSON DSC - 323W Bedienungsanleitung

AVer

AVer FB2027 Bedienungsanleitung

ENFORCER

ENFORCER EV-T5105-N2SQ Bedienungsanleitung

Wansview

Wansview NC543 Bedienungsanleitung

Eneo

Eneo MCB-64A0003M0A Bedienungsanleitung

deView electronics

deView electronics CBDNI36F Bedienungsanleitung

Swann

Swann SwannEye Bedienungsanleitung

LevelOne

LevelOne IP CamSecure Bedienungsanleitung