Samsung 2 COLOR THERMAL PRINTER SRP-370 Bedienungsanleitung

USER’S MANUAL

SRP-370/372

THERMAL RECEIPT PRINTER

All specifications are subjected to change without notice

http://www.samsungminiprinters.com

Safety Precautions

In using the present appliance, please keep the following safety

regulations in order to prevent any hazard or material damage.

Violating following instructions can cause serious injury or death.

Do not plug several products in one

multi-outlet.

This can provoke over-heating and a fire.

If the plug is wet or dirty, dry or wipe it

before usage.

If the plug does not fit perfectly with the

outlet, do not plug in.

Be sure to use only standardized

multi-outlets.

You must use only the supplied adapter.

It is dangerous to use other adapters.

Do not pull the cable to unplug.

This can damage the cable, which is the

origin of a fire or a breakdown of the printer.

Keep the plastic bag out of children’s reach.

If not, a child may put the bag on his head.

Do not plug in or unplug with your hands

wet.

You can be electrocuted.

Do not bend the cable by force or leave it

under any heavy object.

A damaged cable can cause a fire.

If you observe a strange smoke, odor or

noise from the printer, unplug it before

taking following measures.

Switch off the printer and unplug the set

from the mains.

After the disappearance of the smoke, call

your dealer to repair it.

WARNING

PROHIBITED

PROHIBITED PROHIBITED

ONLY SUPPLIED ADAPTER

PROHIBITED

TO UNPLUG

PRINTER

Violating following instructions can cause slight wound or damage the appliance.

Keep the desiccant out of children’s

reach.

If not, they may eat it.

Install the printer on the stable surface.

If the printer falls down, it can be broken

and you can hurt yourself.

Use only approved accessories and do

not try to disassemble, repair or remodel

it for yourself.

Call your dealer when you need these

services.

Do not touch the HEAD of printer with

your hand.

This can burn your hand or deteriorate

printing quality.

Do not let water or other foreign objects

in the printer.

If this happened, switch off and unplug the

printer before calling your dealer.

Do not use the printer when it is out of

order. This can cause a fire or an

electrocution.

Switch off and unplug the printer before

calling your dealer.

WARNING

HEAD

PROHIBITED

PRINTER

PROHIBITED

PRINER

DISASSEMBLING

PROHIBITED

PRINTER

PROHIBITED

PRINTER

DEALER

TO UNPLUG

Warning - U.S.

This equipment has been tested and found to comply with the limits for a Class A digital

device pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the user will be required to

correct the interference at his own expense.

Notice - Canada

This Apparatus complies with class “A” limits for radio interference as specified in the

Canadian department of communications radio interference regulations.

Get appareil est conforme aux normes class “A” d’interference radio tel que specifier par

ministre canadien des communications dans les reglements d’interference radio.

Caution

Some semiconductor devices are easily damaged by static electricity. You should turn the

printer “OFF”, before you connect or remove the cables on the rear side, in order to guard

the printer against the static electricity. If the printer is damaged by the static electricity,

you should turn the printer “OFF”.

INTRODUCTION

The SRP-370/372 Roll Printer are designed for use with electronic instruments such as

system ECR, POS, banking equipment, computer peripheral equipment, etc.

The main features of the printer are as follows:

1. High speed printing : 47(1/6” Feed) lines per second.

2. Low noise thermal printing.

3. RS-232, Parallel, USB

4. The data buffer allows the unit to receive print data even during printing.

5. Peripheral units drive circuit enables control of external devices such as

cash drawer.

6. Characters can be scaled up to 64 times compared to it’s original size.

7. Bar code printing is possible by using a bar code command.

8. Different print densities can be selected by DIP switches.

Please be sure to read the instruction in this manual carefully before using your new

SRP-370/372.

NOTE : The socket-outlet shall be near the equipment and it

shallbeeasyaccessible.

Table of Contents

CHAPTER 1. SETTING UP THE PRINTER ..................................... 5

1-1. UNPACKING .............................................................................. 5

1-2. CONNECTING THE CABLES ............................................................. 6

1-3. CONNECTING THE COMPUTER ......................................................... 7

1-4. CONNECTING THE DRAWER ........................................................... 7

1-5. CONNECTING THE POWER SUPPLY ................................................... 8

1-6. INSTALLING OR REPLACING THE PAPER ROLL...................................... 9

1-7. ADJUSTMENTS AND SETTINGS ...................................................... 11

1-8. USING THE PRINTER.................................................................. 12

1-9. SETTING THE DIP SWITCHES ........................................................ 13

1-10. SETTING THE MEMORY SWITCHES................................................ 15

CHAPTER 2. HEXADECIMAL DUMPING ..................................... 17

CHAPTER 3. THE SELF TEST ...................................................... 18

CHAPTER 4. CODE TABLE.......................................................... 19

CHAPTER 5. CONTROL COMMANDS LIST.................................. 36

APPENDIX ................................................................................. 84

A. CONNECTORS ............................................................................. 84

RS-232C Cable Connector ......................................................... 85

Interface Connector.................................................................. 85

Drawer Connector .................................................................... 87

B. NOTES ..................................................................................... 87

C. SPECIFICATION ........................................................................... 88

Chapter 1. Setting Up the Printer

1-1. Unpacking

Your printer box should include these items. If any items are damaged or missing,

please contact your dealer for assistance.

SRP-370/372 Cover Cable

Roll Paper Operator’s manual AC Adapter Power Code

1-2. Connecting the Cables

You can connect up the three cables to the printer. They all connect to the connector

panel on the back of the printer, which is shown below:

POWER DK

PARALLEL

Notes : Before connecting any of the cables, make sure that both the printer and the

host are turned off.

Power

Supply

onnector

Drawer

Kick-out

onnector

Interface Connector

1-3. Connecting the computer

You need an appropriate interface cable.

1. Plug the cable connector securely into the printer’s interface connector.

2. Tighten the screws on both sides of the cable connector.

3. Attach the other end of the cable to the computer.

1-4. Connecting the Drawer

WARNING:

Use a drawer that matches the printer specification. Using an improper drawer may

damage the drawer as well as the printer.

CAUTION:

Do not connect a telephone line to the drawer kick-out connector; otherwise the

printer and the telephone line may be damaged.

Plug the drawer cable into the drawer kick-out connector on the back of the printer

next to the power supply connector.

1-5. Connecting the Power Supply

CAUTIONS:

When connecting or disconnecting the power supply from the printer, make sure that

the power supply is not plugged into an electrical outlet. Otherwise you may damage

the power supply or the printer.

If the power supply’s rated voltage and your outlet’s voltage do not match, contact

your dealer for assistance. Do not plug in the power cord. Otherwise, you may damage

the power supply or the printer.

1. Make sure that the printer’s power switch is turned off, and the power supply’s

power

cord is unplugged from the electrical outlet.

2. Check the label on the power supply to make sure that the voltage required by the

power supply matches that of your electrical outlet.

3. Plug in the power supply’s cable as shown below. Notice that the flat side of the

plug faces down.

Notes : To remove the DC cable connector, make sure that the power supply’s power

cord is unplugged; then grasp the connector at the arrow and pull it straight out.

1-6. Installing or Replacing the Paper Roll

1. Make sure that the printer is not receiving data; otherwise, data may be lost.

2. Open the paper roll cover by pressing the cover-open button.

3. Remove the used paper roll core if there is one.

4. Insert the paper roll as shown.

Notes : Be sure to use paper rolls that meet the specifications. Do not use paper rolls

that have the paper glued to the core because the printer cannot detect the

paper end correctly.

Notes : Do not open the print cover while the printer is operating.

This may damage the printer.

5. Be sure to note the correct direction that the paper comes off the roll.

6. Pull out a small amount of paper, as shown. Then close the cover.

Feed

paper

Error

Power

7. Tear off the paper as shown.

Feed

paper

Error

Power

Notes : When closing the cover, press the center of printer cover firmly to prevent

er miss-loadin

1-7. Adjustments and Settings

1)It has 2 features ; Paper end and Black mark. For detecting Paper End,

it must be positioned at “a” Position in drawing and it is a factory default setting.

For detecting Black mark printed on the paper, it must be moved to “b” position.

2) Optical density (O.D) must be higher than 0.6 in density to secure a standard working

condition.

Make sure if the density of paper black mark is lesser it might be a cause of normality.

3) Table of O.D value (Reference)

1.4 0.9 0.6 0.3 0.2

1-8. Using the Printer

Control Panel

Button

The button can be disabled by the ESC c 5 command.

Press the FEED button once to advance paper one line. You can also hold down the

FEED button to feed paper continuously.

Panel lights

POWER

The POWER light is on whenever the printer is on.

ERROR

This indicates an error.

PAPER OUT

This light indicates the near end of the paper roll. Install a new paper roll and the

printer Will continue printing.

When the light blinks, it indicates the self-test printing standby state or macro

execution Standby state when the macro execution command is used.

1-9. Setting the DIP Switches

Serial Interface(RS-232C, RS-485) Specification

DIP Switch Set 1 Functions

Switch No. Function ON OFF Default

SW1-1 OFF

SW1-2 Baud Rate Selection Refer to below Table OFF

SW1-3 Handshaking Hardware

(DTR/DSR)

Software

(Xon/Xoff) OFF

SW1-4 Reserved -- OFF

SW1-5 Cutter Function Disable Enable OFF

SW1-6 Paper 2 Color Mono OFF

SW1-7 Reserved -- OFF

SW1-8 Reserved -- ON

Baudrateselection

Dip Switch Set 2 Functions

Switch No. Function ON OFF Default

SW2-1 OFF

SW2-2 OFF

SW2-3

Select Print Density Refer to below Table

OFF

SW2-4 Historical Control Enable Disable OFF

SW2-5 Reserved -- OFF

SW2-6 Interface Condition

Selection

by Memory

Switch

by DIP

Switch OFF

SW2-7 Reserved -- OFF

SW2-8 Printing width 2” Printing 3” Printing OFF

SW1-1 SW1-2 Trans- Speed Remark

OFF OFF 9600 Baud

ON OFF 19200 Baud

OFF ON 38400 Baud

ON ON 115200 Baud Default

Print Density

Parallel/USB Interface Specification

Switch No. Function ON OFF Default

SW2-1 OFF

SW2-2 OFF

SW2-3

Select Print Density Refer to below Table

OFF

SW2-4 Historical Control Enable Disable OFF

SW2-5 Reserved -- OFF

SW2-6 Interface Condition

Selection

by Memory

Switch

by DIP

Switch OFF

SW2-7 Reserved -- OFF

SW2-8 Printing width 2” Printing 3” Printing OFF

Print Density

2-1

2-2

2-3 Print Density Remark

ON ON ON 130%

OFF ON ON 120%

ON OFF ON 110%

OFF OFF ON 105%

OFF OFF OFF 100% Default

ON OFF OFF 95%

OFF ON OFF 90%

ON ON OFF 80%

2-1

2-2

2-3 Print Density Remark

ON ON ON 130%

OFF ON ON 120%

ON OFF ON 110%

OFF OFF ON 105%

ON OFF OFF 100% Default

OFF OFF OFF 95%

OFF ON OFF 90%

ON ON OFF 80%

Dip Switch Set 1

SW 5 ON Auto Cutter Disabled

Application Ignores Auto Cutter error for continuous printing.

※Auto Cutter Enable / Disable selection

1-10. Setting the Memory Switches

This printer has “Memory Switch” set which is software switches. Memory Switch set has

“MSW1”, “MSW2”, “MSW8”, “MSW9” “Customize value”, “Serial communication condition”.

“Memory Switch setting utility” can change the Memory Switch set to ON or OFF as shown

in the table below (default : all OFF) :

Settings of the Memory Switch are stored in the NV memory : therefore, even if the printer

is turned off, the settings are maintained.

MSW1

Switch Function ON OFF

1~4 Reserved -- Fixed to OFF

5 Auto Line Feed Enable Disable

6~8 Reserved -- Fixed to OFF

MSW2

Switch Function ON OFF

1~2 Reserved -- Fixed to OFF

3 Auto Cutter Function Full Cutting Partial Cutting

4~8 Code Page Selection Refer to following Table

Notes : The Memory Switch is available to be changed by three methods :

- Memory Switch setting utility.

- Control from ESC/POS command.

MSW2-8 MSW2-7 MSW2-6 MSW2-5 MSW2-4 Character Table

OFF OFF OFF OFF OFF Page 0 437

OFF OFF OFF OFF ON Page 1 Katakana

OFF OFF OFF ON OFF Page 2 850

OFF OFF OFF ON ON Page 3 860

OFF OFF ON OFF OFF Page 4 863

OFF OFF ON OFF ON Page 5 865

OFF OFF ON ON OFF Page 16 1252

OFF OFF ON ON ON Page 17 866

OFF ON OFF OFF OFF Page 18 852

OFF ON OFF OFF ON Page 19 858

OFF ON OFF ON OFF Reserved

OFF ON OFF ON ON Page 22 864

OFF ON ON OFF OFF Page 23 Thai42

OFF ON ON OFF ON Page 24 1253

OFF ON ON ON OFF

OFF ON ON ON ON

ON OFF OFF OFF OFF

Reserved

ON OFF OFF OFF ON Page 28 1251

ON OFF OFF ON OFF Page 29 737

ON OFF OFF ON ON Reserved

ON OFF ON OFF OFF Page 31 Thai16

ON OFF ON OFF ON Reserved

ON OFF ON ON OFF Page 33 1255

ON OFF ON ON ON

ON ON OFF OFF OFF Reserved

ON ON OFF OFF ON Page 36 855

ON ON OFF ON OFF Page 37 857

MSW8

Switch Function ON OFF

1~8 Reserved -- Fixed to OFF

MSW9

Switch Function ON OFF

1 Reserved -- Fixed to OFF

2 Data Length 7 Bits 8 Bits

3 Parity Selection Even Odd

4 Parity Check Enable Disable

5 Flow Control DTR/DSR XON/XOFF

6~8 Baud Rate Selection Refer to following Table

MSW9-8 MSW9-7 MSW9-6 Baud Rate

OFF OFF OFF 9600

OFF OFF ON 19200

OFF ON OFF 38400

OFF ON ON 57600

ON OFF OFF 115200

Chapter 2. Hexadecimal Dumping

This feature allows experienced users to see exactly what data is coming to the printer.

This can be useful in finding software problems. When you turn on the hexadecimal dump

function, the printer prints all commands and data in hexadecimal format along with a

guide section to help you find specific commands.

To use the hexadecimal dump function, follow these steps:

1. After you make sure that the printer is off, open the cover.

2. Turn on the printer, while holding down the FEED button.

3. Close the cover, then the printer enters the hexadecimal dump mode.

4. Run any software program that sends data to the printer. The printer will print all the

codes it receives in a two-column format. The first column contains the hexadecimal

codes and the second column gives the ASCII characters that corresponds to the

codes.

0000: 1B 21 00 1B - 26 02 40 40 ¦ . ! . . & . @ @

0008: 40 40 02 0D - 1B 44 0A 14 ¦ @ @ . . . D . .

0010: 1E 28 28 28 - 00 01 0A 41 ¦ . ( ( ( . . . A

zA period (.) is printed for each code that has no ASCII equivalent.

zDuring the hex dump, all commands except DLE EOT and DLE ENQ are

disabled.

5. When the printing finishes, turn off the printer.

6. Turn on the printer and then the hexadecimal mode is off.

Chapter 3. The self test

The self-test checks whether the printer has any problems. If the printer does not function

properly, contact your dealer. The self-test checks the following;

1. Make sure paper roll has been installed properly.

2. Turn on the power while holding down the FEED button. The self-test begins.

3. The self-test prints the current printer status, which provides the control ROM version

and the DIP switch setting.

4. After printing the current printer status, self-test printing will print the following, and

pause (The PAPER LED light blinks).

Self-testprinting.

PleasepresstheFEEDbutton

5. Press the FEED button to continue printing. The printer prints a pattern using the

built-in character set.

6. The self-test automatically ends and cuts the paper after printing the following.

*** COMPLETED ***

The printer is ready to receive data as soon as it completes the self-test.

Chapter 4. Code Table

The following pages show the character code tables. To find the character corresponding

to a hexadecimal number, count across the top of the table for the left digit and count

down the left column of the table for the right digit. For example, 4A = J.

Page 0 ( PC437 : USA, Standard Europe)

( International Character Set : USA )

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Samsung Drucker Handbücher

Samsung

Samsung CLX-4195 Series Bedienungsanleitung

Samsung

Samsung Network Printer Bedienungsanleitung

Samsung

Samsung QL 6100 Bedienungsanleitung

Samsung

Samsung CPL-310N Bedienungsanleitung

Samsung

Samsung CLP 500 Bedienungsanleitung

Samsung

Samsung ML--6100 Kurzanleitung

Samsung

Samsung MFP SCX-6345N Benutzerhandbuch

Samsung

Samsung Xpress M2675FN Bedienungsanleitung

Samsung

Samsung ML-2550 Benutzerhandbuch

Samsung

Samsung ML-1650 Series Bedienungsanleitung

Samsung

Samsung ML-2525W series Bedienungsanleitung

Samsung

Samsung STP-102P Bedienungsanleitung

Samsung

Samsung CLP-680ND: CLP-775ND Bedienerhandbuch

Samsung

Samsung CLP-650N Bedienungsanleitung

Samsung

Samsung ML-4050N Referenzhandbuch

Samsung

Samsung SF-330 Series Bedienungsanleitung

Samsung

Samsung ML-2850 Series Bedienungsanleitung

Samsung

Samsung CLP-770ND - Color Laser Printer Bedienungsanleitung

Samsung

Samsung ML-1755 Bedienungsanleitung

Samsung

Samsung CLP-415 series Bedienungsanleitung

Samsung

Samsung CLP-300 Bedienungsanleitung

Samsung

Samsung ML-5100A Bedienungsanleitung

Samsung

Samsung ELLIX-35II Bedienungsanleitung

Samsung

Samsung Xpress M2020W Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung

Lexmark

Lexmark Infoprint 1332 Bedienungsanleitung